Price Pfister R89-XP Series User manual

A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
Copyright
©
2005, Price Pfi ster, Inc.
© 2005, Price Pfi ster, Inc. ©
10-13
-05
EO6857J
30031
-0200
R89-XP S
eries
Serie
R89-
XP
R89-XP R89-
S
é
rie
R89-
XP
R89-XP R89-
Tub & Shower • Shower Only
Trim Kit
Juego con acabado para
Tinas y duchas o
●
duchas solamente
Bain et douche
●
Douche seule
Kit de garniture

ENGLISHENGLISH
ENGLISH
Thank you for purchasing this Price Pfi ster product. All Price Pfi ster products are carefully engineered, and factory tested to provide long
trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions. If you
trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions. If you
have any questions regarding your product installation call 1-800-Pfaucet (1-800-732-8238)
have any questions regarding your product installation call 1-800-Pfaucet (1-800-732-8238)
.
1 BEFORE PROCEEDING
1 BEFORE PROCEEDING
WARNING:
Read all the instructions completely before proceeding. Price
Pfi ster recommends calling a professional if you are uncertain about installing
Pfi ster recommends calling a professional if you are uncertain about installing
this product!
this product!
This product should be installed in accordance with all local and state plumbing
This product should be installed in accordance with all local and state plumbing
and building codes.
and building codes.
WARNING:
This product has been designed for use with the Price Pfi ster
0X8 series pressure balancing valve. It will not work with any other product.
Please review the 0X
8
valve installation instructions before installing this
product
2 SHUT OFF WATER SUPPLY
L
o
ca
te water supply inlets and shut off the water supply valves. These are
usually fou
nd near the water meter. If you are replacing an existing unit, remove
the old unit and clean the mounting surface thoroughly.
3 TOOLS RECOMMENDED
• PTFE plumber's tape or thread sealant
• Philips head screwdriver • Adjustable wrench • Pipe wrench
• Flashlight • Cloth
Your installation will require a pipe nipple for the spout installation as well as
other additional tools.
4
CHECKING THE CONTENTS OF THE BOX
Upon opening the box, check to ensure that all of the following items are included.
A
Gasket Flange
B
Trim Flange
C
Washer
D
Retainer Sleeve
E
Stem
Extension
F
Handle
G
Set Screw
H
Hex Wrench
J
Diverter Spout
K
Shower Arm
L
Shower Head
M
Shower Flange
If any of these items are missing, please contact Price Pfi ster Consumer Service
at 1-800-Pfaucet (1-800-732-8238).
5 WORK AREA INSPECTION
Verify that the hole sizes and positions in the wall are correct.
6 PLASTERGUARD OPTIONS
A
.
For installation using plasterguard, knock out Center Section (
6B
) from Plasterguard
(
6A
). The use of plasteguard is optional for standard installations.
B
.
For installation without plasterguard, remove Screws (
6C
), and
Plasterguard
(
6A
).
INSTALLATION STEPS
4
5
6
3
2
30”
Tub & Shower
48”
Tub & Shower
8” Min.
30”
Shower Only
48”
Shower Only
1
1
/
4
4
” Dia.
4
3
/
4
” Dia.
4” Dia. for Thin
Wall Installation
1
1
/
4
4
” Dia.
A
B
A
B
C
D
E
F
G
H
J
K
L
M
6B
6A
6C
6A

ENGLISHENGLISH
ENGLISH
7 TRIM FLANGE ATTACHMENT
Position Flange (
7A
) on Valve (
7B
) with Drain Hole (
7C
) at the bottom. Place
Protective Washer (
7D
) on the short end of the reversible Retainer Sleeve (
7E
).
7E). 7E
Screw Retainer Sleeve (
7E
) onto threaded section of the Stem and Bonnet (
7E) onto threaded section of the Stem and Bonnet (7E
7G
).
Tighten Retainer Sleeve (
7E
) by hand until Flange (
7E) by hand until Flange (7E
7A
) is snug to fi nished wall
surface. If the short end of the Retainer Sleeve (
7E
) is too short, reverse it to
7E) is too short, reverse it to 7E
use the longer end.
8 HANDLE ATTACHMENT
Screw Stem Extender (
8A
) onto the Valve Stem (
8B
). Thread the Set Screw (
8C
)
into the Handle (
8D
) and thread it in only three to four turns. Place Handle (
8D
)
onto the Stem Extender (
8A
) and tighten the Set Screw (
8C
) by using the Hex
Wrench (
8E
) that is provided.
8E) that is provided.8E
Make sure Set Screw (8C) is securely tightened to handle
(
8D
)
.
10 SPOUT INSTALLATION
A. For Copper Pipe Connections:
Connect Copper Tube (
10A
) into the elbow inside the wall and remove the sharp
edges all around the outer tube (
10B
). The
Copper Tube
(
10A
) is to project 3
1
/
4
” to 3
3
/
8
” from the fi nished wall. Press Tub Spout (
10C
) onto Pipe Nipple
(
10A
) until spout is properly positioned and fl ush to the fi nished wall surface.
Tighten Set Screw (
10D
) located at the bottom of spout.
B. For Threaded Iron Pipe Connections:
Apply PTFE plumbers tape on both ends of Pipe Nipple (
10A
) (not included).
Screw Pipe Nipple (
10A
) into the elbow inside the wall and tighten with pipe
wrench. The Pipe Nipple (10A) is to project 3
7
/
8
” to 4” from the fi nished wall.
Remove Internal Connector (
10E
) from Spout (
10C
). Screw Tub Spout (
10C
)
onto Pipe Nipple (
10A
) and tighten until Spout is properly positioned and fl ush
to the fi nished wall.
11 UNIT START UP
Turn on hot and cold water supplies, and check all connections for leaks.
9 SHOWER ARM INSTALLATION
Insert the end of Shower Arm (
9A
) through the Shower Flange (
9B
). Apply PTFE
plumber's tape to both ends of Shower Arm (
9A
) according to manufacturer's
instructions. Screw the end of Shower Arm (
9A
) into pipe elbow inside the wall.
Slide Shower Flange (
9B
) tight to the wall.
7
8
9
10
3
7A
8A
9A
7B
7C
7C
7D
7E
7G
8B
8C
8D
8E
9B
10A
10A
3
7
/
8
”
to
4
”
10B
3
1
/
4
”
to
3
3
/
8
”
10
C
10
D
A
B
10A
10A
10
E
10
C

ENGLISHENGLISH
ENGLISH
13 TUB SPOUT FUNCTION
When the valve is turned on, water normaly fl ows through the Tub Spout (
13A
).
To activate the shower, turn valve on and pull the Knob (
13B
) up. Hold on until
water fl ows continiously from the shower arm.
15 SHOWER HEAD INSTALLATION
Thread Shower Head (
15A
) onto Shower Arm (
15B
).
Make sure Shower Head (
15A
) is securely tightened to Shower Arm
(
15B
).
CAUTION: Maintenance
DISASSEMBLY
1. Replacement parts may be available at the store where you purchased
your faucet.
2. When replacement parts are not available, please write or call Price
Pfi ster Consumer Service.
3.
Always turn off water and relieve pressure before working on your
faucet.
NOTE: Trim Care
Cleaning Instructions:
For all Handles and decorative fi nishes, use only a soft damp
cloth to clean and shine. Use of polish, detergents, abrasive
cleaners, organic solvents or acid may cause damage.
Use of
other than a soft damp cloth will nullify our warranty!
Special Trim:
Trim products which contain Porcelain or other similar
substance are not acceptable for public areas or Commercial
use. Installation of Said Trim is at Users Risk!
12 VALVE FUNCTION
By rotating the Lever Handle (
12A
) slightly counterclockwise, the valve will
be fully activated to the “COLD” position. The water temperature can be
increased by continuing to rotate the Lever Handle (
12A
) in a counterclockwise
direction.
14 FINAL FLUSHING
For fi nal fl ushing, turn valve on and allow water to run through the Tub Spout
(
14A
) for several minutes. Pull Spout Knob (
14B
) up to allow water to run through
Shower Arm (
14C
). Allow water to run for several minutes untill all foreign mater
clears the line.
UP
For
Shower
MAINTENANCE & CARE
13
12
14
15
4
FULL
HOT
FULL
COLD
CLOSED
OPEN
12A
12A
15A
15A
1
5
B
14A
14A
14B
14C
13A
13A
13B

ENGLISHENGLISH
ENGLISH
1–800–PFAUCET (1–800–732–8238)
For Toll-Free Pfaucet information call
1–800–PFAUCET (1–800–732–8238)
or visit www.pricepfi ster.com
• Installation Support
• Care and Warranty Information
Temperature or fl ow does not remain consistent.
The Cartridge Assembly (
D
) may need cleaning. Shut off water supply. Remove
Handle Assembly (
A
), unscrew Retainer Sleeve (
B
) and remove Flange (
C
).
Remove Cartridge assembly (
D
) and inspect Cartridge (
E
) and inlets for debris
E) and inlets for debris E
or sediment and fl ush with water. Reassemble whole unit and test. If problem
persists you may need to replace the Cartridge (
E
).
E).E
Sleeve (B) is too short.
Extension kit 910-563 is available at a nominal charge for valves which have
been roughed-in too far back in the wall. The kit contains a one inch stem
extension, and longer screw and a sleeve which is one inch longer than the
972-300.
Dripping from either the tub spout or shower head.
Clean the Cartridge Assembly (
D
). Check to ensure the two Oval O-Rings (
F
)
F) F
on the back of the Cartridge (
E
) are in place. Reassemble cartridge, stem and
E) are in place. Reassemble cartridge, stem and E
bonnet assembly and handle. Turn on the water and test. If the unit still leaks,
replace the Cartridge (
E
).
E).E
Make sure that both hot and cold water inlets are turned on.
Water fl ow is very low.
Check the Cartridge Assembly (
D
), for debris. Sediment where the water enters
), for debris. Sediment where the water enters
the Shower Head (
G
) can also cause this symptom.
Water starts out hot and becomes cooler as handle is rotated counter
clockwise.
This is a potentially hazardous situation and should be corrected before using
This is a potentially hazardous situation and should be corrected before using
the unit. Check the hot and cold inlet positions (hot- left cold-right). If you have
the unit. Check the hot and cold inlet positions (hot- left cold-right). If you have
a back to back installation, (where hot and cold inlets are reversed) refer to
Valve Body instruction sheets for back to back installation.
Water fl ows from the shower head while fi lling the tub.
Check the position of the Valve Body (
J
). The letters “SHWR” should be cast
J). The letters “SHWR” should be cast J
into the top and “TUB” on the bottom.
Water doesn’t get hot enough.
Remove Handle (
A
), Sleeve (
B
) and Flange (
C
) and then refer to Valve Body
instruction sheets for adjusting temperature range.
Water fl ows from the tub spout while using the shower.
The seal inside of the diverter mechanism may have become dislodged. The
Spout (
H
) may need replacement.
TROUBLE SHOOTING TIPS
5
A
B
C
D
E
F
G
H
J

19701 DaVinci
Lake Forest, CA 92610
Phone: 1-800-Pfaucet
www.pricepfi ster.com
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
A COMPANY
R89-XP
*
*
Letter Designates FinishLetter Designates Finish
La Letra Indica el Terminado
La Letra Indica el Terminado
La Lettre Designe La FiniLa Lettre Designe La Fini
A
Polished Chrome
Cromo Pulido
Chrome Poli
J
PVD Brushed Nickel
PVD
Niquel Cepillado
PVD
Nickel Brosse
973-
030
*
960-
062
*
9
60-059*
972-300
*
9
50-620
971-023
920-
411
*
9
40-088
*
973-0
83
*
971-024