Primex XR Levo Series User manual

©2018 Primex. All Rights Reserved. The Primex logo is a registered trademark of Primex. All other trademarks are the property of their respective owners. 12/7/2018. Primex, Inc. |
965 Wells Street | Lake Geneva, WI 53147 | www.primexinc.com | Ph: 1-262-729-4853
XR Levo Series Digital Clocks/Timers
Install Guide
Primex XR 72MHz Synchronized Time Solution

Legal Notice
Copyright ©2018 Primex, Inc. All rights reserved.
Printed in the USA.
Information in this document is subject to change without notice. Software described in this document is furnished under a license
agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of those
agreements.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic,
mechanical or otherwise, for any purpose, without the prior written permission of Primex, Inc.
Primex, Inc.
Primex is a leading provider of synchronized time and environmental monitoring solutions. Our solutions automate and maintain
facility compliance, increase efficiencies, enhance safety and reduce risk for organizations in the healthcare, education,
manufacturing and government vertical markets.
Worldwide Headquarters
965 Wells Street, Lake Geneva, WI 53147
Phone: [phone] | email: [e-mail] | www.primexinc.com
2XR Levo Series Digital Clocks/Timers Install Guide

Regulatory Compliance
FCC/IC Product Compliance
This device complies with part 15 of the FCC rules as well as with Industry Canada.
Operation of this device is subject to the following two conditions:
lThis device may not cause harmful interference.
lThis device must accept any interference that may cause undesired operation.
3

Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT.
Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE INSTALLATION, OPERATION, OR MAINTENANCE OF PRODUCT.
Some of the following information may not apply to your particular product model; however, as with any electronic product,
precautions should be observed during installation, operation, and maintenance.
lInstallation must conform to state or local building codes and ordinances.
lInstallation or maintenance should be performed only by qualified personnel as defined in the Local Electrical Code.
lMount in location where device will not readily be subject to tampering.
lAny wiring instructions must be followed precisely. Failure to do so could cause permanent equipment damage.
lTo avoid possible electric shock or damage to the device, disconnect power source before installation or servicing.
lDo not install or use device near water. To reduce the risk of electrical shock, do not expose device to rain or moisture. Device
must not be exposed to dripping or splashing and no objects filled with liquids, such as vases, must be placed on the device.
lDevice is designed for indoor use only. Operating outdoors, or in wet areas, is an electrical hazard and may damage the
equipment while nullifying the warranty.
lDevice is cleanable with a cloth moistened with water or a common disinfectant. Be sure to test any cleaning solutions on a small
area of the clock before using it on the entire device.
lFor healthcare facilities, devices are not intended for patient use and must not be installed within 6ft (2m) of patient contact.
AC-Power Pluggable Clock/Timer Models
lAC main power supply must be disconnected while installing or performing maintenance of any device. To completely
disconnect the power input, the main plug should be disconnected from the main socket outlet completely.
lThe main socket outlet must provide a protective earthing connection where the outlet has a protective earth (ground)
connection.
lMain plug is used as disconnect device and it should remain readily operable during intended use.
AC-Power Hardwired Clock/Timer Models
lAC power must be supplied from a circuit that has a resettable circuit breaker.
lAC mains power supply must be disconnected while installing or performing maintenance of any device. Open the circuit
breaker supplying the device before attempting installation, maintenance, or repairs.
4

About this Guide
Purpose
This guide is intended to provide the instructions and information required to install and operate Primex Levo Series Digital
Clocks/Timers.
Typographical Conventions
This guide includes notes, cautions, and warnings content that highlights important messages.
Typeface Indicates
Note Indicates something important or useful.
Caution Indicates a command or procedure may have an unwanted or undesirable result.
Warning Indicates a command or procedure that could be dangerous to system or device.
Example Provides an example of how the topic can be configured or used.
5

Contents
Specifications 9
Timer Switch Control Specifications 10
Configure Display Settings 14
Install Levo Series Digital Clock/Timer 17
Installation Requirements 17
120 VAC Wiring & Power Specifications 18
24 VAC Wiring & Power Specifications 19
Tilt-Bracket and Surface Mount Mounting Dimensions 20
Surface Mount Installation 22
Tilt Bracket Installation 24
Remove Clock/Timer from Bracket 26
Dual Mount Installation 27
Dual Mount Dimension Specifications 30
Remove Digital Clock/Timer from Dual Mount Bracket 31
Flush Mount Installation 32
Flush Mount Dimension Specifications 35
Remote Antenna Installation 36
Timer Switch Control Installation 38
Code Blue Timer Operation 40
Timer Switch Control Specifications 41

Elapsed Timer Operation 44
Programmable Timer Operation 48
Support 49
Five Year Limited Warranty 50
7

8

Specifications
Listed below are the components and specifications of a Levo Series Digital Clock/Timer.
Components
lKey-hole mount (2); secure mount
lPower supply
lPower cord with 2-prong plug
lPower cord strain relief assembly
lSetting panel; configure clock settings and location of Reset button
lCode Blue Timer: 4 pin connector 30 in. (76.2 cm) length; RJ 11 jack for connection from the timer to the timer control switch
The figure below illustrates the back of a Levo Series Digital Clock/Timer and its components.
Levo Series Digital Clock/Timer Specifications
Parameter Specification
LED Display Highly visible 7-segment LED digits
2.5" model: 2.5” (6.4 cm) diagonal (hours and minutes), 1.4" (3.6 cm) diagonal (seconds)
4" model: 4.6” (11.7 cm) diagonal (hours and minutes), 2.5” (6.4 cm) diagonal (seconds)
LED Display Dimmer 100%, 75%, 50%, 25%
9XR Levo Series Digital Clocks/Timers Install Guide

Parameter Specification
Time Display 12- or 24-hour time
PM indicator light
Alternating time and date display option
Hour Offset +/- 24 hours
Receiver Sensitivity
(Decode)
< -110dBm
Power Supply 100-240 VAC/ 50–60 cycle. Supplied with 10 ft (3.0 m) cord with plug and UL/cUL listed power
supply
24VAC model: 18-28VAC/ 50–60 cycle. Supplied with a 10 in. (25 cm) cord with pigtail and power
supply
Power Outage Memory
Backup
In the event of a power outage, its internal memory maintains the correct time for a minimum of
one hour without power; requires a minimum one hour of charging time.
Enclosure ABS plastic
Junction box: UL listed (UL 50E 1st Ed; listing number E469550)
Storage Temperature Range -20° to 185° F (-29° to 85° C)
Operating Temperature
Range
32° to 194° F (0° to 35° C)
Code Blue Timer Input 5-120 VAC/ DC /DC or dry contact input
Code Blue and Elapsed
Timer Audible Beep Option
Frequency 3KHz +/-0.5KHz
Certification FCC/IC/CE marked
All specifications are subject to change without notice.
Timer Switch Control Specifications
The Primex 3 button Timer Switch Control provides the method manage events for both the Elapsed and Code Blue Timer. Elapsed
Timer count down or count up events are triggered manually by a user from the timer switch control buttons. Code Blue Timer
events are triggered by the input of the wired connection to the code blue system and the timer switch control allows a user to
10