Func COOEE COLLABORATION WALLBOARD User manual

PAGE 1
ASSEMBLY GUIDE
SIZE GUIDE & CONTENTS FOR Collaboration Wallboard
x1 Collaboration
Wallboard
Tools you will need:
1207mm x 2413mm
[47.5in x 95in]
Phillips Head
Screw Driver
Spirit LevelLaser Level Tape Measure Electric Drill
Two Person
Install
CAUTION
• Clear open space for install
• Installer is responsible for
installing Z clips to the wall.
• + 25lbs lift required
COOEE
COLLABORATION
WALLBOARD &
WHITEBOARD
0
x1 Collaboration
Whiteboard
603mm x 2413mm
[23.75in x 95in]
1207mm x 1207mm
[47.5in x 47.5in]
603mm x 1207mm
[23.75in x 47.5in]
2413mm x 483mm
[95in x 19in]
2413mm x 1207mm
[95in x 47.5in]
1207mm x 1207mm
[47.5in x 47.5in]
Lorem
2413mm x 1207mm
[95in x 47.5in]
x4 MDF Batten
800mm [31.50in]
x4 MDF Batten
400mm [15.75in]
x2 MDF Batten
800mm [31.50in]
x2 MDF Batten
400mm [15.75in]
x4 MDF Batten
800mm [31.50in]
SIZE GUIDE & CONTENTS FOR Collaboration Whiteboard
1207mm x 2413mm
[47.5in x 95in]
x4 MDF Batten
800mm [31.50in]
x4 MDF Batten
800mm [31.50in]
x4 MDF Batten
800mm [31.50in]
x2 MDF Batten
800mm [31.50in]
Suitable Screws For Different
Surfaces
Screws Are Not Included

PAGE 2
ASSEMBLY GUIDE
a.
Insert MDF Battens into Collaboration Wall-
board. Measure from the floor to the desired
height of the bottom MDF Batten. See drawing
above.
b.
Match Collaboration Wallboard spacing onto
your solid wall (Surface). Ensure MDF Battens
are the correct direction and level. Check
with a laser or spirit level.
Installer to use fixings appropriate to Solid
wall construction.
COOEE
COLLABORATION
WALLBOARD &
WHITEBOARD
1
2
HEIGHT OF THE GROUND
Prepare your MDF Battens before measurement.
Drill holes on MDF Battens suitable for you select-
ed screws (Screws For Different Surfaces).
Two holes per MDF Batten required.
Before drillinling check the surface for obstacles.
37.59in 954.9mm
9.87in
250.8mm
37.59in 954.9mm
4.70in
119.3mm
SURFACE
MDF
BATTEN

PAGE 3
ASSEMBLY GUIDE
a.
When installing multiple Cooee Collaboration Wallboards / Whiteboards, laser level is recommend
as the floor or ceiling may not be level. This will warrant any mis-alignment and help in a fast
and accurate install.
Installer is responsible for
installing MDF BATTENS to the wall.
Ensuring they are structurally
sound to hang a Collaboration
Wallboard / Whiteboard and desired
accessories.
COOEE
COLLABORATION
WALLBOARD &
WHITEBOARD
3
4
a.
Ensure MDF Battens are correct direction
for installation. Also make sure the
screws are flush as they will interfere
with acoustic PET panel.
Gravity
CAUTION
GROUND LINE
SURFACE
MDF
BATTEN
COLLABORATION
WALLBOARD /
WHITEBOARD

PAGE 4
ASSEMBLY GUIDE
a.
Once MDF Battens are secure on the solid wall,
the Cooee Collaboration Wallboard / Whiteboard
can be lifted in place. This requires 1-2
people. Make sure pressure is applied at the
front of the acoustic PET to ensure MDF Battens
and Wallboard lock into each other.
b.
Once Cooee Collaboration Wallboard is
lifted in place. Make sure it is centered
over the MDF Battens. Slight adjusments on
both sides is possible.
COOEE
COLLABORATION
WALLBOARD &
WHITEBOARD
5
x1 Assembled
Collaboration
Wallboard
x1 Assembled
Collaboration
Whiteboard
OR