Princeton Lcd2000 User manual

REFERENCE MANUAL

LCD2000

Part No.: 14MP2003A00

Ref No.: 00300000367

are subject to change without notice. Princeton Digital (USA) Corp. is not responsible for printing or clerical errors. Windows® is a registered trademark of Microsoft Corporation. Apple® and

MacintoshTM are registered trademarks of Apple Computer, Inc. Energy Star® is a U.S. registered trademark. As an Energy Star® Partner, Princeton Digital (USA) Corp. has determined that this

product meets Energy Star® guidelines for energy efficiency .

www.princetongraphics.com

BACK COVER FRONT COVER

Glossy Cover

Pantone 8223 non varnished

FCC Information

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help .

FCC Warning:

To assure continued FCC compliance, the user must use the provided grounded power

supply cord and the provided shielded video interface cable with bonded ferrite cores. Also,

any unauthorized changes or modifications to this TFT LCD would void the user's authority

to operate this device.

Canadian Complaince Statement:

This equipment does not exceed Class B limits per radio noise emissions for a digital

apparatus, set forth in the Radio interference regulation of the canadian Department of

Communications. Operation in a residential area may cause unacceptable intereference to

radio and TV reception requiring the owner or operator to take whatever steps necessary to

crrect the intereferece.

Important Safety Instructions:

Power:

• Use the type of power indicated on the marking label.

Plugs:

• Do not remove any parts of the Display’s three-pronged power plug.

• Disconnect the power plug from the AC outlet when the display will not be used for an indefinite

period of time.

Power and extension cords

• Use the proper power cord with the correct plug type. If the power source is 120VAC, use a power

cord that has UL and CSA approvals. If the power source is 250VAC supply, use the tandem (T

Blade) type attachment plug with a ground conductor power cord that meets the respective

European counties safety regulations, such as VDE for Germany.

We recommend using the power cord supplied with the product. However, if another type of power

cord is required, power cord H05VV-F, or VW-1, 18AWG x 3G should be used.

Do not overload wall outlets or power cords. Be sure that the total of all units plugged into the wall

outlet does not exceed 7 amperes.

Be sure that the total ampere ratings on all units plugged into the extension cord does not exceed the

rating of the cord.

If the display power supply cord requires a connection to the PC instead of the wall outlet, this

equipment is to be used with a UL approved computer which has a receptacle rated of 100~240VAC,

50/60Hz, (minimum)

Environment

• Place the display on a flat and leveled surface.

• Place the display in a well-ventilated area.

• Keep the Display away from water, excessive heat, cold, or humidity.

• Do not place the power cord on a walkway or rest anything heavy on top of it.

• Keep the display stable at all times.

Table of Content

FCC Information ----------------------------------------------------------------------------------------- 1

FCC Warning ---------------------------------------------------------------------------------------------- 1

Safety Precautions --------------------------------------------------------------------------------------- 1

Important Safety Instructions ------------------------------------------------------------------------- 2

Getting Started

Package Contents -------------------------------------------------------------------------------------- 4

Unique Features ---------------------------------------------------------------------------------------- 4

Precautions ----------------------------------------------------------------------------------------------- 5

Cleaning the TFT LCD Monitor ---------------------------------------------------------------------- 5

QuickInstallation --------------------------------------------------------------------------------------- 6

Operation

Front Control Panel -------------------------------------------------------------------------------------9

Hot Key ---------------------------------------------------------------------------------------------------9

OSD Main Menu ----------------------------------------------------------------------------------------9

COLOR Sub-Menu ------------------------------------------------------------------------------------ 10

LCD Sub-Menu ---------------------------------------------------------------------------------------- 10

MISC Sub-Menu -------------------------------------------------------------------------------------- 11

Technical Data

Specifications ------------------------------------------------------------------------------------------ 12

Factory Preset Timings ------------------------------------------------------------------------------- 13

GETTING STARTED

Thank you for choosing Princeton and congratulations on your purchase of a TFT LCD

Color Monitor. This section lists package contents, features, precautions, as well as

cleaning and installation instructions.

Important ! Please keep the original box and all packing

material for future shipping needs.

Package Contents

Your TFT LCD Color Monitor package includes the following:

• TFT LCD Color Monitor

• Video cable (DB15)

• DVI Cable (DVI-D)

• Power Cord

• This Reference Manual

Monitor Features:

• High resolution, High Contrast color Active Matrix TFT-LCD providing sharp, vivid, and

flicker-free images.

• Energy Star® Compliant for Maximized Energy Saving.

• Plug & Play Compatibility with DDC2B.

• True Native Resolution of 1600 x 1200.

• Free run features that will search the right frequency without interface.

• Composite Sync. and Sync-On-Green Compatibilities.

• Five Selectable Languages.

• Smart Out-of-Sync and No Signal Indications.

• Support for Image Smoothing for lower resolutions.

• True Native 1600 x 1200 Resolutions.

Precautions

• Sit at least 20.1” away from the TFT LCD Color Monitor.

• Do not press the LCD Display as it is very fragile.

• Do not touch the LCD panel with bare hands, the grease from your skin is difficult to

remove and may damage the screen.

• Do not expose the LCD monitor to direct sunlight or other heat sources. When in use, the

LCD screen should be facing away from light sources to reduce glare.

• Choose a well-ventilated area to place your LCD monitor.

• Do not place anything on top of the LCD Monitor.

• Ensure the area around the LCD Monitor clean and moisture-free.

• Do not place heavy objects on the power cord, adapter, video or audio cables.

• If smoke, abnormal noise, or strange odor occurs, immediately turn the LCD monitor off

and call your dealer. It is dangerous to continue using the LCD monitor.

• Do not remove the rear cover by yourself, the display units contains high-voltage

components, you may be expose to the electric shock hazard. Contact your local dealer

for the service if it is needed.

• Always handle your LCD monitor with care when moving it.

Cleaning the TFT LCD Color Monitor

• Wipe the screen gently with a clean lens brush of camel hair, or a soft, clean, lint-free cloth.

It can remove dust and other particles that may not scratch the LCD panel.

•Never poor or spray anyliquid onto the LCD monitor.

•Donot apply pressure to the LCD DISPLAY.

Unpacking

Carefully lift the LCD monitor out of the packaging and make sure that all the components

are included. Please save the original box and packaging materials for future shipments.

Connecting

To connect the monitor to your PC:

1. Make sure that the PC and monitor are unplugged.

2. Connect the 15-pin signal cable to the monitor and the PC

3. Optional: If you have a graphic card with a digital DVI connector (24-pin socket), then

connect one end of the DVI cable to the DVI connector of your monitor and the other end to

the computer.

4. Connect one end of the Power cord to the monitor, and connect the other to the wall

outlet.

STARTUP

Start your PC and then turn your monitor on. (Power button) The Green LED should light up.

Adjust the image to meet your requirements (Contrast & Brightness) if you desire. See

below for descriptions on how functions work.

BASIC SETUP

Automatic Image Adjustment

You can adjust the image settings (such as brightness, contrast, image position, phase, etc.)

manually or by using the LCD monitor’s automatic image adjustment feature. This will adjust

the image parameters to their optimal settings for the current graphics mode. Press AUTO

button to launch the automatic adjustment.

Selecting the Input Signal (INPUT)

You can switch the signal source directly from D-Sub (Analog 1) to DVI (Analog 2/Digital)

by pressing the INPUT button

Shortcut for adjusting contrast and backlight.

You can adjust contrast and backlight directly by pressing the - or + buttons while the OSD

menu is not displayed. Press the INPUT button and then the + button to increase the

contrast/ backlight, or press - only to decrease the contrast/ backlight.

IMAGE SETTINGS USING THE OSD MENU

The OSD menu is a window on your screen that allows you to view and change display

settings. To change an OSD setting: (1=Activate OSD, 2=Decrease, 3=Increase,

4=Auto Adjustment, 5=Input Select, 6=Power LED, 7=Power Button)

1. Press the MENU button to display the OSD menu on the screen.

2. There are a total of 7 OSD submenus divided by categories. Select the submenus by

pressing the OSD buttons –or +.

3. Press the MENU button to activate the selected function or associated submenu.

4. If you select a submenu and select the function you want to use, now press the MENU

button, then press the - and + OSD button.

5. Set the desired value using the – or + buttons.

6. If you select the input signal source you want to use, please press the INPUT button

7. Press the AUTO button to save the settings. Repeat steps 2~5 to make further

adjustments as needed.

8. The OSD menu automatically disappears if no changes are made for more than 30

seconds (default settings). The current settings will be saved. You can close it

manually by pressing the MENU button.

OSD MENU FUNCTIONS

Brightness

Press the MENU button to adjust the overall image and background screen brightness

Select the desired category by pressing the OSD's -or +buttons.

Contrast

Press the MENU button to adjust the image brightness in relation in the background.Select

the desired category by pressing the OSD's -or +buttons.

Manual Adjust

Clock: Controls the picture's horizontal size.

Phase: Improves focus. clarity and image stability by increasing or decreasing this

setting.

H. Position: Controls horizontal image position within the display area oh the LCD

V. Position: Controls Vertical image position within the display area oh the LCD

Color Temperature

Four different color temperatures are available: sRGB, 9300 K, 7000K,6500 K ,.

If you want to change the RGB color components yourself, choose from among the

Red, Green and Blue values by pressing the MENU. Adjust the value by pressing the -

or + buttons.

ECO Mode

Off: close ECO Mode, use normal the background screen brightness and contrast

On: open ECO Mode, use designate the background screen brightness and contrast

Language

Selects the OSD menu language: Japanese, English, Frencais, Deutsch, Espanol.

Other

Smooth: Controls image sharpness

OSD H. Position: Controls the horizontal image position of the OSD menu

OSD H. Position: Controls the Vertical image position of the OSD menu

OSD Transparency: Sets the OSD menu to transparent or with a background.

OSD Timeout: Determines the time (in seconds)to wait before the OSD menu is

automatically closed when no changes are made.

Mode Message: Shows the current operating mode. If activated, a message will

appear for three seconds when you restart your computer or modify the operating

mode.

Reset: Restores the image settings to their factory values.

Specification

LCD panel

Contrast ratio

Viewing angle

Response time

Brightness

Input signal

Display colors

Synchronization

Video band width

Native resolution

Power connection

Power consumption

Dimensions / weight

Operating environment

20.1 inch diagonal size

700:1(typical)

Horizontal 170°,vertical 170°(typical)

Rise time: 15ms, Fall time: 10ms(typical)

250 cd/m2(typical)

Video: analog (D-SUB and DVI-I) and digital (DVI-D)

16.7 mill colors

30~83kHz horizontal, 50~86 Hz vertical

162 MHz (pixel rate)

1600 × 1200 (60 Hz)

Input: AC 90-264V (power built in)

On status: max. 45W; color of the status LED: green

SLEEP status: < 2W; color of the status LED: orange

Power saving functions EPA certified

Width: 445.5mm, height: 434.7~505mm, depth: 226.6mm;

10.1kg(net)

Operation: 0 to +40°C, humidity: 10~80%(without

condensation)

Storage: -20 to +60°C, humidity: 10~85%(without

condensation)

Factory preset timings

Timing Hor. Freq (Khz) Ver. Freq (Hz)

VGA 640x350

31.470

70.089

+/-

VGA 720x400

31.467

70.082

-/+

VGA 640x400

24.825

56.420

-/-

VGA 640x480

31.469

59.940

-/-

VESA 640x480

37.861

72.809

-/-

VESA 640x480

37.500

75.000

-/-

MAC 640x480

35.000

66.667

composite

VESA 800x600

35.156

56.250

+/+

VESA 800x600

37.879

60.317

+/+

VESA 800x600

48.077

72.188

+/+

VESA 800x600

46.875

75.000

+/+

MAC 832x624

49.715

74.535

composite

VESA 1024x768

48.363

60.004

-/-

VESA 1024x768

56.476

70.069

-/-

VESA 1024x768

58.036

71.916

-/-

VESA 1024x768

60.023

75.029

+/+

MAC 1024x768

60.241

74.927

composite

VESA 1280x1024

63.981

60.020

+/+

VESA 1280x1024

79.976

75.025

+/+

VESA 1152x 864 67.500 75.000 +/+

VESA 1600x1200

75.000

60.000 +/+

REFERENCE MANUAL

LCD2000

Part No.: 14MP2003A00

Ref No.: 00300000367

are subject to change without notice. Princeton Digital (USA) Corp. is not responsible for printing or clerical errors. Windows® is a registered trademark of Microsoft Corporation. Apple® and

MacintoshTM are registered trademarks of Apple Computer, Inc. Energy Star® is a U.S. registered trademark. As an Energy Star® Partner, Princeton Digital (USA) Corp. has determined that this

product meets Energy Star® guidelines for energy efficiency .

www.princetongraphics.com

BACK COVER FRONT COVER

Glossy Cover

Pantone 8223 non varnished

Table of contents