PRO connect SS2.1 User manual

SS2.1 Sound Stage
Table-Top Surround Sound System
OWNER’S MANUAL

IMPORTANT SAFETY INSTRUCTION APPLICABLE FOR USA, CANADA OR
WHERE APPROVED FOR USAGE
CAUTION: TO PREVENT ELECTRIC
SHOCK, MATCH WIDE BLADE PLUG TO
WIDE SLOT, INSERT FULLY.
1. Read these instructions.
2. Keep these instructions.
3. Follow all instructions.
4. Do not use this apparatus near water.
5. Clean only with a damp cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
8. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider
than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete
outlet.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where
they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the appara-
tus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be
placed on the apparatus.
15. Servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform
any servicing other than that contained in the operating instructions unless you are qualified to do so.
16. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
17. Where the MAIN plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily
operable.
18. Danger of explosion if remote control battery is incorrectly replaced. Replace only with the same or equivalent type
(CR2025). Do Not Expose Batteries to excessive heat such as direct sunlight, fire, etc. Dispose of dead batteries in accor-
dance with local regulations. To satisfy FCC RF Exposure Requirements, a separation distance of 20 cm or more should be
maintained between the antenna of this device and persons during device operation.
19. Under Industry Canada Regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada.
CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user- serviceable parts inside.
Refer servicing to qualified service personnel. This equipment is a Class II or double insulated electrical appliance.
2

3
Pro-Connect Sound Stage SS2.1
Includes
1 - Stereo Sound Stage
1 - IR Remote Control
1 - Lithium Battery (3V, CR2025)
1 - Stereo RCA Patch Cable
1 - Digital Optical Patch Cable
1 - AC Power Cord
Features
• Simulated surround sound from a single, space-saving cabinet
• Enjoy deep, enveloping bass without bulky speakers or amps
• Includes advanced Digital Signal Processing (DSP)
• Use with flat-panels TVs and digital music players
• Syncs to almost any Bluetooth audio device
Amplifier Specs:
Bi-amp design; independent amp channels for each woofer and each set of midrange
drivers and tweeter
20W Continuous x 4 Channels into 40 for 80 Watts Total Amplification 35Hz - 20kHz; <1% THD
Audio Inputs:
1 - Digital Coaxial Audio Input
1 - Digital Optical Audio Input
1 - Stereo Analog Line Level Audio Input 1 Bluetooth Input
Speaker Configuration:
- Stereo
- Four Front-facing 2-1/2” Midrange Drivers
- Two 1” Silk Dome Tweeters
- Two Down-firing 5-1/4” Subwoofers
- Ported Enclosure
IR Remote Control
• ON/Standby
• Volume & Mute
• Discrete Input Select
• Treble & Bass Adjustment
• Simulated Surround Sound (Toggle On/Off)

4
Congratulations and thank you for purchasing the Pro-Connect Sound Stage Table-Top Surround Sound System. The
Pro-Connect Sound Stage greatly enhances the sound quality of today’s flat screen LED, LCD and Plasma TVs without having
to add a lot of speakers. A single speaker system that requires very little space, the SOUND STAGE can be installed below or
in front of a high definition TV or inside a cabinet. You’ll enjoy simulated surround sound from a single, space- saving cabinet
with deep, enveloping bass without bulky speakers or amps. The Pro-Connect SOUND STAGE easily connects to inputs on
today’s flat panel TVs and digital music players and even syncs to almost any Bluetooth audio device.
SOLID BLUE – ON – Pro-Connect SOUND STAGE is ON.
SINGLE BLUE FLASH - Confirms receiving an IR command from the Pro-Connect Sound Stage Remote for changes to
Treble/Bass, EQ Reset, Simulated Surround (SR), single Volume UP/DOWN command, initiating output of the Bluetooth
Connection Code.
RAPID BLUE FLASH - Confirms receiving a continuous IR stream from the SOUND STAGE Remote for ramping volume
UP/DOWN. Rapid blue flash also indicates the SOUND STAGE is in Bluetooth pairing mode.
SLOW BLUE FLASH - Audio Mute. Audio signal to the speakers is turned OFF.
TWO BLUE FLASHES; DELAY -Bluetooth input is selected and no Bluetooth device is connected or it is out of range.
2. IR SENSOR - (Behind front panel lens.) The IR Sensor ‘sees’ the IR control commands output from the SOUND STAGE IR
Remote Control when buttons are pressed on the remote for armchair control of the SOUND STAGE. This sensor must be
unobstructed for direct line-of-sight to the remote, or the remote will not be able to control the SOUND STAGE.
3. FRONT AND REAR PANEL BASS PORTS -Two pairs of tuned openings in the SOUND STAGE cabinet allow air to
‘release’ from the cabinet and enhance low frequency audio. Allow at least 3 inches of clearance to a back wall to allow air to
move freely from the ports for full bass extension.
Pro-Connect
SOUND STAGE
FRONT PANEL
INTRODUCTION
Pro-Connect
SOUND STAGE
REAR PANEL
12
3 3
Back Panel Connection Plate
1. STATUS LED - (Behind front panel lens.) One multi-color LED. This LED will illuminate red/blue and flash in different modes
to indicate changes in the SOUND STAGE operational status. SOLID RED - OFF (Standby). Power cord is connected and AC
switch is turned ON, but the SOUND STAGE is OFF.

5
4. DIGITAL COAXIAL INPUT -
One RCA jack. Connect to the
Digital Coaxial OUT on a TV or
other source. This input is selected
by pressing the COAX button on
the SOUND STAGE IR Remote.
NOTE: The audio output of a TV,
Blu-ray Disc player, game console,
or DVD player connected to the
SOUND STAGE via Coaxial Digital
must be set to PCM in the source’s
setup. Please see the device’s
Owner’s Manual for details.
5. DIGITAL OPTICAL INPUT - One TOSLINK® connector. Connect to the Digital Optical OUT on a TV or other source. This
input is selected by pressing the OPT button on the SOUND STAGE IR Remote.
NOTE: The audio output of a TV, Blu-ray Disc player, game console, or DVD player connected to the SOUND STAGE via
Optical Digital, must be set to PCM in the source’s setup. Please see the device’s Owner’s Manual for details.
6. AUDIO INPUT - Two RCA jacks. Connect to the L & R Line Level Audio OUT on a TV or other source. This input is selected
by pressing the AUX button on the Pro-Connect SOUND STAGE IR Remote.
7. POWER - Turns the power to the Pro-Connect SOUND STAGE ON/OFF. Always turn the power OFF when making connec-
tions to the SOUND STAGE. The Front Panel LED will illuminate red to indicate Standby (power switch ON, SOUND STAGE
turned OFF with IR Remote) or blue to indicate that the SOUND STAGE is ON.
8. AC INPUT-Universal power connector. Automatically selects AC voltage for a given region. Connect to the included
2-conductor AC Power Cord. After all audio connections have been made and confirmed, plug the power cord into an
un-switched AC Outlet to power the SOUND STAGE.
9. DOWN FIRING SUBWOOFERS - The SOUND STAGE bottom panel features two 5-1/4” subwoofers, one for left channel
bass and one for right channel bass. When handling the SOUND STAGE, be careful not to grab or hold the cabinet bottom
where the woofers are located to prevent damaging the woofers. Also take care to not set the cabinet down on anything but a
flat surface clear of obstructions.
CONNECTION PANEL
When placing the SOUND STAGE
on a shelf or stand, be sure there
are no objects under the cabinet
that will damage or block the woof-
ers and check to make sure there
are no objects on the sides of the
cabinet that will block the space
under the SOUND STAGE. Block-
ing this space will reduce overall
bass performance.
7
8
65
4
Shown With Grill Shown Without Grill
9

6
1. POWER - Press this button to turn the SOUND STAGE ON/OFF.
2. INPUT - Press to select a connected source. The SOUND STAGE Front Panel Status LED will flash once to indicate a
change in input selection.
COAX - Press to select the Digital Coaxial Input.
OPT - Press to select the Digital Optical Input.
AUX - Press to select the L&R Line Level Audio Input
Press to select a paired Bluetooth device. A Bluetooth device must be paired to the PRO-Connect SOUND STAGE for
audio output. A paired Bluetooth device will remain ‘connected’ after changing inputs as long as the Bluetooth device
has not moved out of range, turned off or otherwise disconnected.
3. Press this button to initiate Bluetooth pairing mode. The Front Panel Status LED will rapid flash blue. The SOUND STAGE
will output a pairing code that will be picked up by any active Bluetooth device that is within range of the SOUND STAGE.
4. VOLUME -/+ Press VOL - to reduce volume. Press VOL + to increase volume.
5. MUTE -Press this button once to mute the SOUND STAGE. Press again to un-mute the SOUND STAGE.
6. SURR -Press this button to activate the simulated surround audio mode. Press again to turn Surround Mode OFF.
7. EQ RESET -Press this button to cancel any changes to the Treble and Bass controls. Remote Control Battery
Replacement CAUTION: When replacing the lithium battery in the remote, make sure that the replacement battery is inserted in
correct polarity. Place the battery so that its positive (+) side faces up with the tray held so that the surface with the dot and (+) is
facing up.
8. BASS -/+ Press BASS - to reduce low frequency output. Press BASS + to increase low frequency output.
9. TREBLE -/+ Press TREBLE - to reduce high frequency output. Press TREBLE + to increase high frequency output.
Pro-Connect SOUND STAGE IR REMOTE CONTROL

7
Flat Screen TV SOUND STAGE A/V Sources
TABLE TOP INSTALLATION
The SOUND STAGE is ideally designed for table top installation. In this application the SOUND STAGE is placed on a cabinet
top and becomes a pedestal for the TV. Very little space is required beyond what is already used by the TV.
DOWN-FIRING WOOFERS/REAR PORTS
The SOUND STAGE should always be placed on a solid surface, maintaining the clearance on the bottom of the unit required
for low-frequency sound to freely radiate into the room. Do not place objects next to the SOUND STAGE that will block this
space. The SOUND STAGE has two rear bass ports that enhance low frequency sounds. These ports should remain unob-
structed with a clearance of at least three inches to a back wall to assure proper performance.
The cabinet top should be at least seventeen inches deep to properly support the SOUND STAGE. The SOUND STAGE is
sixteen and a half inches deep (with grille attached) and extra space will be required between the SOUND STAGE and a wall
behind the cabinet for cables connecting the SOUND STAGE to the TV or other A/V sources (3 inches minimum).
Note: The TV pedestal should not be larger than the top of the SOUND STAGE (28”W x 16”D)
CABINET INSTALLATION
........................
........................
Cabinet Depth:
17” minimum
SOUND STAGE TV PEDESTAL
Top View of Flat Panel TV
with stand sitting on top of
Sound Stage

8
HARDWIRED AUDIO CONNECTIONS
The Pro-Connect SOUND STAGE has three hardwired Audio Input connections on the rear panel that can be used for TV audio
or connection to other sources such as CD player, a portable music player (that does not have Bluetooth), a computer or any
audio source with one of the following output connections.
OPTICAL DIGITAL AUDIO
Connect the Optical Digital Audio OUT on a TV or
other source to the Pro-Connect SOUND STAGE
Optical Input using a Digital Optical Audio Cable as
shown. This Input is selected by pressing the ‘OPT’
button on the included IR Remote. NOTE: The
audio output of a TV, Blu-ray Disc player, game
console, or DVD player connected to the SOUND
STAGE via Optical Digital, must be set to PCM in
the source’s setup. Digital connection to a CD
player does not require a special setting.
COAXIAL DIGITAL AUDIO
Connect the Optical Digital Audio OUT on a TV or
other source to the Pro-Connect SOUND STAGE
Optical Input using a Digital Optical Audio Cable as
shown. This Input is selected by pressing the ‘OPT’
button on the included IR Remote. NOTE: The
audio output of a TV, Blu-ray Disc player, game
console, or DVD player connected to the SOUND
STAGE via Optical Digital, must be set to PCM in
the source’s setup. Digital connection to a CD
player does not require a special setting.
L&R AUDIO
Connect the L&R Audio OUT on a TV or other
source to the SOUND STAGE L&R Audio Input
using a Stereo RCA-RCA Patch Cable as shown.
This Input is selected by pressing the ‘AUX’ button
on the included IR Remote.
AC POWER CORD
After all audio connections have been made and
confirmed, connect the female end of the included
power cord to the AC Input on the SOUND STAGE
rear panel, and then plug the AC power cord into
an un-switched AC outlet. The AC connection is a
universal power connection that will automatically
handle AC voltage from 100-240VAC.
TV/Source Audio Outputs
Digital Optical Audio Cable
TV/source
Optical Output
TV/source
Optical Output
Digital Coaxial Audio Cable
Stereo RCA Patch Cable
TV/Source Audio Outputs
TV/Source Audio Outputs
Sound Stage
Audio Inputs
Sound Stage
Audio Inputs
Sound Stage
Audio Inputs

OPERATING THE Pro-Connect SOUND STAGE
Press the SURR button on the SOUND STAGE IR Remote to turn the simulated surround ON. Front panel Status LED
will flash once.
Press the SURR button on the SOUND STAGE IR Remote to turn the simulated surround OFF. Front panel Status LED
will flash once.
SIMULATED SURROUND
The SOUND STAGE utilizes advanced Digital Signal Processing (DSP) to create simulated surround sound from a
stereo speaker configuration. The SOUND STAGE simulated surround can also be used for music.
PAIRING AND SELECTING A BLUETOOTH SOURCE
The SOUND STAGE will pair without the need to enter a code, if the device implements Bluetooth v2.1 or later. Legacy pairing is
the only method available for Bluetooth v2.0 and older. Each device must enter a PIN code: ‘0000’ to complete pairing. To ensure
that your device is compatible, look for the Bluetooth Music Icon on the packaging, or go to: www.gadgetguide.bluetooth.com
PAIRING A BLUETOOTH DEVICE
1. Turn the SOUND STAGE and the Bluetooth device ON.
2. Press the button on the SOUND STAGE IR Remote to select the Bluetooth Input. The front panel Status LED flash twice, delay
then repeat.
3. On the device to be paired to the SOUND STAGE, turn Bluetooth ON. The Bluetooth controls are typically found in the device’s
‘Settings’ or ‘Connections’ menu. If the Bluetooth device has previously been paired with the SOUND STAGE, and the SOUND
STAGE has not been removed from the list of discovered devices, the Bluetooth device should automatically sync with the
SOUND STAGE. (Front panel Status LED solid blue.)
4. Press the button on the SOUND STAGE IR Remote for a Bluetooth device that has not been paired with the SOUND STAGE,
or the SOUND STAGE has been removed from its list of discovered devices. The SOUND STAGE will output a sync code that will
be received by the Bluetooth device. The front panel Status LED will flash rapidly until the Bluetooth device accepts the BT Code
and pairs to the SOUND STAGE.
5. The device will appear in the Bluetooth setup screen on the device being paired.
6. The device should sync to the SOUND STAGE. The front panel Status LED will stop flashing and illuminate solid blue.
7. If switching between hardwired sources and a paired Bluetooth device, the Bluetooth device will remain ‘connected’ as long as
the device has not been turned OFF or moved out of Bluetooth range. If the Bluetooth device has been turned OFF, simply turn it
ON, navigate to the device’s Bluetooth setup and sync to the SOUND STAGE
9

Power Output 20W Continuous x 4 Channels into 4O for 80 Watts Total Amplification;........
THD (at rated power)...................................................................................
Damping Factor.........................................................................................
Input Sensitivity (For rated power @ max VC, analog L&R Inputs)...............................
Input Impedance (analog L&R Inputs)................................................................
Input Overload (analog L&R Inputs)..................................................................
Frequency Response..................................................................................
Channel Separation....................................................................................
Cross Talk Between Sources..........................................................................
S/N Ratio (A-Wtd, db below 1 Watt)..................................................................
Bass Control Range.....................................................................................
Treble Control Range..................................................................................
35Hz to 20kHz
<1.00%
> 15
335 mV
20 K Ohms
2.0Vrms
35 Hz to 20 kHz
> 50 dB @ 10 kHz
> 60 dB @ 10 kHz
-78 dB
± 8 dB @ 100 Hz
± 6 dB/-10dB @ 10 kHz
Speakers
Down-firing Subwoofers................................................................................
Mid Range Drivers......................................................................................
Tweeters.................................................................................................
Two x 5-1/4” Treated Paper Cone
Four x 2-1/2” Treated Paper Cone
Two x 1” Silk Dome
Power Consumption 120V
Standby..................................................................................................
No signal (idle)..........................................................................................
At 1/8 of Rated Power (2.5 Watts/Channel, 4O).....................................................
Rear Panel marked Line Ratings......................................................................
<0.5 Watts
14 Watts
40 Watts
100~240V~ 50~60Hz 100W
Dimensions : (H x W x D) 4” x 28” x 16-1/2” (102mm x 711mm x 419mm) 16” (406mm) Depth with grille removed
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Weight : 25 lbs. (11kg)
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by
OSD Audio is under license. Other trademarks and trade names are those of their respective owners.
Note: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates audio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
SPECIFICATIONS AUDIO
10



LIMITED TWO-YEAR WARRANTY
11
Limited Warranty
Pro-Connect warrants to the original retail purchaser only (“you”) that this product will be free from defects in materials and
workmanship for a period of two years (the “Warranty Period”), subject to the limitations and exclusions set out in this Limited
Warranty. This warranty is not transferable to subsequent owners of the product. If you discover a defect in material or
workmanship within the Warranty Period, contact Pro-Connect

NOTE
12
AVAD LLC -16648 N 94th St - Scottsdale, AZ 85260 - 866.for.AVAD (367-2823) - www.avad.com