Pro-Elec PE01138 User manual

INSECT KILLER
Model: PE01138

• When using electrical appliances basic safety precautions should be
followed.
• Check that the voltage indicated on the rating plate corresponds with that
of the local network before connecting the appliance to the mains power
supply.
• High voltage! Do not touch the inner electric grids.
• Never insert any metal objects inside the grid while it is in operation.
• This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety in
a safe way and understands the hazards involved.
• Children should be supervised to ensure that they do not play with the
appliance.
• This appliance is not to be used in locations where ammable vapour or
explosive dust is likely to exist.
• This appliance is designed for indoor use only.
• The appliance cannot be used in a garage, stable or similar environment.
• This appliance is intended for domestic use only. It should not be used for
commercial purposes.
• Do not operate the appliance with a damaged plug or cord, after a
malfunction or after being dropped or damaged in any way.
• If the supply cord is damaged, it must be replaced by a qualied engineer
in order to avoid injury or hazard.
• Clean the collection tray regularly. It’s recommended that you clean the
device monthly or more frequently if necessary.
WHAT’S INCLUDED
• The Electronic Insect Killer utilises ultra-violet light, which is the most
effective lure for light sensitive ying insects, such as ies, moths and
mosquitoes.
• The insects are electrocuted by the high voltage inner grid.
• The Electronic Insect Killer involves no chemicals, no sprays, no mess,
has no smell and is pollution-free and harmless to humans and pets.
• Insect Killer combined with 13A plug.
• User manual.
IMPORTANT SAFETY INFORMATION
HOW IT WORKS
Please read these instructions carefully before use and retain for future reference.

MAINTENANCE
If the lamp inside the Insect Killer requires replacing, follow the steps below.
CAUTION: Ensure the appliance is disconnected from the mains prior to
changing the lamp.
Remove the collection tray by
squeezing the two recesses on the
tray rmly and pulling the tray away.
Note: Remove the tray over a rubbish
bag to avoid dropping any insects.
Release the clips of the lamp
cover using a screwdriver. Pull the
screwdriver in the direction indicated
above.
Pull the connector away from the pin
and gently move to one side.
To remove the lamp, hold the end
of the lamp and pull it up towards
yourself.
1. 2.
3. 4.
5. When tting a new lamp ensure it is securely tted with the two pins facing
towards you at the base of the appliance and with the pins set parallel to
the lines on the base of the Insect Killer (see Fig. 3).
6. Once the lamp is in place reverse the above instructions to re-t the
connector and collection tray.
7. To re-t the lamp cover simply place it back over the connector and pins,
before clipping it back into place.
Note: The connector can be tted onto any of the two pins.

The collection tray will require regular cleaning. It is recommended that the
tray is emptied and cleaned on a monthly basis or earlier if necessary.
• Ensure the Insect Killer is disconnected from the mains power prior to
cleaning.
• To empty the tray, hold the appliance over a rubbish bag before squeezing
the two recesses rmly on either side of the collection tray to dislodge it,
then pull the tray down and away from the outer mesh.
• Empty the insects into the bag and wipe the tray with a soft, dry cloth if
required.
• Once the tray is clean, push it back up onto the Insect Killer, ensuring it
clips back into place and is secure.
CLEANING THE COLLECTION TRAY
When the lamp in this product reaches the end of its life, the recommended
replacement is the PRO-ELEC Spare Tube (Model: PE01139).
RELATED PRODUCTS
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste
Electrical & Electronics Equipment (WEEE). Any WEEE marked products must
not be mixed with general household waste, but kept separate for the treatment,
recovery and recycling of the materials used. Contact your local authority for details
of recycling schemes in your area.
Version 1.0
Made in China. PR2 9PP