Pro-Form 595Pi User manual

Model No. PFTL43105.0
Serial No.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number
Decal
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT DI-
RECTLY.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.proformservice.com
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
V

TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
2
PROFORM is a registered trademark of ICON IP, Inc.

1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
amat under the treadmill.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
7. The treadmill should be used only by persons
weighing 275 pounds or less.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women.
Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
10. When connecting the power cord (see page 11),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 11. To purchase a surge suppressor, see
your local PROFORM dealer or call the toll-
free telephone number on the front cover of
this manual and order part number 146148, or
see your local electronics store.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 21 if the treadmill is
not working properly.)
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
17. The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The pulse sensor is intended only as an exer-
cise aid in determining heart rate trends in
general.
18. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 19.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
WARNING: Toreduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
IMPORTANT PRECAUTIONS
3

4
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
21. Inspect and properly tighten all parts of the
treadmill regularly.
22. Never insert any object into any opening.
23. DANGER: Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
WARNING: Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on your treadmill. If a decal is missing, or
if it is not legible, please call the toll-free telephone number on the front cover of
this manual and order a free replacement decal. Apply the decal in the location
shown. Note: The decals are not shown at actual size.

5
Thank you for selecting the new PROFORM®595 Pi
treadmill. The 595 Pi treadmill offers an impressive se-
lection of features designed to make your workouts at
home more effective and enjoyable. And when you’re
not exercising, the 595 Pi treadmill can be folded up, re-
quiring less than half the floor space of other treadmills.
For your benefit, read this manual carefully before
using the treadmill.If you have questions after read-
ing this manual, see the front cover of this manual. To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is PFTL43105.0. The serial
number can be found on a decal attached to the tread-
mill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.proformservice.com/registration.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
BEFORE YOU BEGIN
Handrail
Storage Latch
Key/Clip
Reset/Off
Circuit Breaker
Walking Belt
Cushioned Walking Platform
for maximum exercise comfort
Foot Rail
Power Cord
RIGHT SIDE
Rear Roller
Adjustment Bolts
Console
Fan
Accessory Tray
BACK

ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not
dispose of the packing materials until assembly is completed. Note: The underside of the walking belt is coated
with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the
walking belt or the shipping carton. This is a normal condition and does not affect treadmill performance. If there
is lubricant on top of the walking belt, wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrenches and your own phillips screwdriver ,
rubber mallet , adjustable wrench , and wire cutters .
For help identifying the assembly hardware, see the drawings below. If a part is not in the parts bag, first
check to see if it has been pre-assembled.
1. Make sure that the power cord is unplugged.
Have a second person hold the Upright Base (48) in the
position shown, with the wheel holes at the top. Next, lo-
cate the Left Upright (31), which has an identification
sticker. Orient the Left Upright so the sticker is on the in-
side as shown and the bracket is in the position shown.
Attach the Left Upright (31) to the Upright Base (48) with
two Upright Bolts (40) and two Upright Star Washers
(39). Do not tighten the Upright Bolts yet. Note: There
may be left and right stickers on the Upright Base.
Nut (47)–4
Handrail Bolt (20)–4
Upright Bolt (40)–4
Frame Washer
(33)–2
1/4” Star Washer
(21)–2
Silver Ground
Screw (27)–2
Wheel Spacer (44)–4 Console
Bolt (22)–2
Frame Bolt (32)–2
Wheel Bolt (89)–2
3/4” Screw (2)–4 Endcap Screw
(95)–2
F
Upright Star
Washer (39)–4
Handrail Star
Washer (19)–4
48
Wheel Holes
Sticker
Bracket
40
39
31
1
6

7
2. Orient the Right Upright (36) so the square hole near the
lower end is in the position shown. Attach the Right
Upright to the Upright Base (48) with two Upright Bolts
(40) and two Upright Star Washers (39). Donot tighten
the Upright Bolts yet.
Attach each Wheel (45) to the Upright Base (48) with a
Wheel Bolt (89), two Wheel Spacers (44), and a Nut (47)
asshown. Donot overtighten the Wheel Bolts; the
Wheels should turn freely.
48
Square Hole
45
47
44
89
45 44
36
44
89
47
2
3. Cut the tie securing the Wire Harness (28) in a bundle. Do
not remove the large colored tie on the end of the
Wire Harness.
Orient the Upright Base (48) so the Wheels (45) are at the
bottom. Next, position the Upright Base and the Uprights
(31, 36) around the frame assembly as shown.
Have another person lift the front of the frame assembly
and hold it. Insert the Wire Harness (28) into the square
hole near the lower end of the Right Upright (36) and out
of the top. Next, raise the Uprights (31, 36) so the Upright
Base (48) is flat on the floor. Make sure that the end of
the Wire Harness does not fall into the Right Upright;
it may be helpful to hold the colored tie on the end of
the Wire Harness. 28
Colored Tie
48
28
36 45
3
4. Open the included grease packet, and apply grease to
both sides of each Frame Spacer (34).
Hold one of the Frame Spacers (34) between the frame
assembly and the Right Upright (36); make sure that
the Frame Spacer is oriented as shown in the inset
drawing. Insert a Frame Bolt (32) through a Frame
Washer (33), the Right Upright, the Frame Spacer, and
the bracket on the frame assembly. Be careful not to
pinch the Wire Harness (28) in the Right Upright.
Tighten a Nut (47) several turns onto the Frame Bolt, but
do not fully tighten the Nut yet.
Repeat this step on the left side. Note: There is not a
wire harness on the left side.
Remove the colored tie from the Wire Harness (28).
Frame Assembly
Bracket
Frame Assembly
Hole
32
34
33
4
47
28
36
Right
Side
Left
Side
34
40
39
31

8
28
11
6. Hold the Console Base (26) near the Right Handrail (11).
Attach the end of the ground wire on the Console Base
to the indicated small hole in the Handrail with a Silver
Ground Screw (27).
Connect the Wire Harness (28) to wire harness on the
Console Base (26). Make sure to connect the connec-
tors properly (see the inset drawing). The connectors
should slide together easily and snap into place. If
the connectors do not slide together easily and snap into
place, turn one connector and try again. IF THE CON-
NECTORS ARE NOT CONNECTED PROPERLY, THE
CONSOLE MAY BE DAMAGED WHEN THE POWER
IS TURNED ON.
27
26
Ground
Wire
22
7. Set the console assembly on the Handrails (11, 18); in-
sert the excess wiring down into the Right Handrail.
Attach the console assembly with four 3/4” Screws (2),
two Console Bolts (22), and two 1/4” Star Washers (21)
as shown. Make sure that no wires are pinched. Start
all four Screws and both Console Bolts before tight-
ening any of them.
221
2
11 18
6
7
5. Identify the Right Handrail Endcap (91), which does not
have a cutout in the bottom, and slide it onto the lower
end of the Right Handrail (11). Make sure that the screw
hole in the Right Handrail Endcap is at the bottom. Next,
hold the Right Handrail near the Right Upright (36), and
insert the Wire Harness (28) into the hole in the bottom
of the Handrail and out of the indicated hole in the top.
Then, remove the tie from the Wire Harness.
Set the Right Handrail (11) on the Right Upright (36)
while sliding the lower end of the Handrail onto the
bracket on the Right Upright. Hand tighten two Handrail
Bolts (20) with two Handrail Star Washers (19) into the
Handrail and the Right Upright. Next, slide the Right
Handrail Endcap (91) against the Right Upright, and
tighten an Endcap Screw (95) into the Right Handrail
Endcap. Then, tighten the two Handrail Bolts. Make
sure that the Wire Harness (28) is not pinched.
Attach the Left Handrail (18) and the Left Handrail
Endcap (90) to the Left Upright (31) as described above.
36
31
95
95
91
90
Cutout
28
20
19
18
19
20
11
5
28
Console Assembly
21
22

8. Lower the Uprights (31, 36) until the Handrails (11, 18)
are touching the floor.
See the lower drawing. Position the Uprights (31, 36) so
the treadmill Frame (74) is centered between them.
Firmly tighten the four Upright Bolts (40) and the two
Frame Bolts (32). Be careful not to overtighten the
Frame Bolts.
31
31, 36 32
11, 18
74
36
Top View
8
40
9. Attach the end of the ground wire on the Wire Harness
(28) to the indicated small hole in the Upright Base (48)
with a Silver Ground Screw (27).
Make sure that the grommet is pressed into the side of the
Right Upright (36).
Raise the Uprights (36, 31) to the vertical position.
48
28
36
Grommet
9
27
Ground
Wire
9

10
11. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place; the large allen wrench is used to adjust the
walking belt (see page 17). To protect the floor or carpet, place a mat under the treadmill.
10. Remove the knob from the pin. Make sure that the collar
and the spring are on the pin as shown. Insert the pin
into the Latch Housing (30), and tighten the knob back
onto the pin.
30
10
Knob
Pin
Collar
Spring

11
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the toll-free
telephone number on the front cover of this man-
ual and order part number 146148, or see your local
electronics store.
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpect-
edly, which may result in a fall and serious injury.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
2
Grounded Outlet Box
Grounded Outlet Box
Grounding Plug
Surge Suppressor
Surge Suppressor
Grounding Pin
Adapter
Lug
Metal Screw
Grounded Outlet
Grounding Pin

12
FEATURES OF THE CONSOLE
The treadmill console offers an array of features de-
signed to make your workouts more effective. When
the manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will dis-
play continuous exercise feedback. You can even
measure your heart rate using the handgrip pulse
sensor.
In addition, the console features two trainer programs.
Each program automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive workout. You can even create your own custom
programs and store them in memory for future use.
To use the manual mode of the console, follow the
steps beginning on page 13. To use a trainer
program,see page 15. To create and use a custom
program,see pages 16 and 17.
HOW TO TURN ON THE POWER
Plug in the power cord (see
page 11). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
“reset” position.
Next, stand on the foot rails of the treadmill. Locate the
clip attached to the key (see the drawing above), and
slide the clip securely onto the waistband of your
clothes. Then, insert the key into the console. After a
moment, the displays will light. Test the clip by care-
fully taking a few steps backward until the key is
pulled from the console. If the key is not pulled
from the console, adjust the position of the clip.
Note: To prevent damage to the walking platform,
always wear clean shoes while using the treadmill.
Note: If there are thin sheets of plastic
on the console, remove the plastic. Key
Clip
Reset
CONSOLE DIAGRAM

13
HOW TO USE THE MANUAL MODE
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Select the manual mode.
When the key is inserted,
the manual mode will be
selected. If a program
has been selected, press
the Trainer Programs but-
ton repeatedly until a
track appears in the matrix.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the buttons
numbered 1 through 10.
If the Start button or the
Speed increase button is
pressed, the walking belt
will begin to move at 1
mph. As you exercise,
change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons.Each time a button
is pressed, the speed setting will change by 0.1
mph; if a button is held down, the speed setting
will change in increments of 0.5 mph.
If one of the ten numbered buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting. Note: The
console can display speed and distance in ei-
ther miles or kilometers (see THE INFORMA-
TION MODE/DEMO MODE on page 18). For
simplicity, all instructions in this section refer
to miles.
To stop the walking belt, press the Stop button.
The time will begin to flash in the Time/Pace dis-
play. To restart the walking belt, press the Start
button, the Speed increase button, or one of the
ten numbered buttons.
Note: The first time you use the treadmill, periodi-
cally inspect the alignment of the walking belt, and
center the walking belt if necessary (see page 22).
Change the incline of the treadmill as desired.
To change the incline of
the treadmill, press the
Incline increase and de-
crease buttons. Each time
abutton is pressed, the
incline setting will change
by 0.5%; if a button is held down, the incline set-
ting will change quickly.
Monitor your progress with the displays and
the matrix.
The Incline/Pulse dis-
play—This display will
show the incline level of
the treadmill. This display
will also show your heart
rate when you use the
handgrip pulse sensor.
The Distance/Calories
display—This display will
show the distance that
you have walked or run
during your workout and
the approximate number
of calories that you have burned.
The matrix—When the
manual mode is selected,
the matrix will show a 1/4-
mile track. As you walk or
run, the indicators around
the track will light in suc-
cession until the entire track is lit. The track will
then darken and the indicators will again begin to
light in succession.
The Time/Pace display—
This display will show the
elapsed time. Each time
the speed setting
changes, the display will
also show your pace, in
minutes per mile. Note: When a program is se-
lected, this display will show the time remaining in
the program instead of the elapsed time.
The Speed display—
This display will show the
speed of the walking belt.
5
4
3
2
1

14
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from the
metal contacts.
In addition,
make sure that
your hands are clean.
To measure your heart rate, stand on the foot
rails and place your hands on the metal con-
tacts—avoid moving your hands.When your
pulse is detected, one or two dashes will appear in
the Incline/Pulse display and then your heart rate
will be shown. For the most accurate heart rate
reading, continue to hold the contacts for
about 15 seconds.
Turn on the fan if desired.
To turn on the fan, press the Fan button. To turn
on the fan at high speed, press the button a sec-
ond time. To turn off the fan, press the button a
third time. Note: If the fan is left on when the walk-
ing belt is stopped, the fan will automatically turn
off after a few minutes.
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage posi-
tion, or the treadmill will become damaged. Next,
remove the key from the console and put it in a se-
cure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 18 and turn off the
demo mode.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
8
7
6
Metal Contacts

15
HOW TO USE A TRAINER PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Select a trainer program.
To select a trainer pro-
gram, press the Trainer
Programs button repeat-
edly until “P 1” or “P 2”
appears in the
Distance/Calories dis-
play. When a trainer program is selected, the
maximum incline setting of the program will flash
in the Incline/Pulse display for a few seconds, the
maximum speed setting will flash in the Speed
display, and the program time will appear in the
Time/Pace display. A profile of the speed settings
of the program will scroll across the matrix.
Press the Start button or the Speed increase
button to start the program.
Amoment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into 30 one-minute peri-
ods. One speed setting and one incline setting are
programmed for each period. Note: The same
speed setting and/or incline setting may be pro-
grammed for two or more consecutive periods.
The speed setting for the
first period will be shown
in the flashing Current
Period column of the ma-
trix. (The incline settings
are not shown in the ma-
trix.) The speed settings for the next three periods
will be shown in the columns to the right.
When only three seconds remain in the first period
of the program, both the Current Period column
and the column to the right will flash and a series
of tones will sound. If the speed and/or incline of
the treadmill is about to change, the speed setting
and/or the incline setting will flash to alert you.
When the first period is completed, all speed set-
tings will move one column to the left .The speed
setting for the second period will then be shown in
the flashing Current Period column and the tread-
mill will automatically adjust to the speed and in-
cline settings for the second period. Note: If all six
of the indicators in the Current Period column are
lit, the speed settings may move downward so that
only the highest indicators appear in the matrix.
The program will continue in this way until the
speed setting for the last period is shown in the
Current Period column and the last period ends.
The walking belt will then slow to a stop.
If the speed or incline setting for the current period
is too high or too low, you can manually override
the setting by pressing the Speed or Incline but-
tons. Every few times a Speed button is pressed,
an additional indicator will appear or disappear in
the Current Period column; if any of the columns
to the right of the Current Period column have the
same number of lit indicators as the Current
Period column, an additional indicator may appear
or disappear in those columns as well. Important:
When the current period of the program ends,
the treadmill will automatically adjust to the
speed and incline settings for the next period.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the
Time/Pace display. To restart the program, press
the Start button or the Speed increase button. The
walking belt will begin to move at 1 mph. When the
next period of the program begins, the treadmill
will automatically adjust to the speed and incline
settings for the next period. To end the program,
press the Stop button, remove the key, and then
reinsert the key.
Follow your progress with the displays.
See step 5 on page 13.
Measure your heart rate if desired.
See step 6 on page 14.
Turn on the fan if desired.
See step 7 on page 14.
When the program is completed, remove the
key.
See step 8 on page 14.
7
6
5
4
3
2
1
Current Period

16
HOW TO CREATE A CUSTOM PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Select a custom program.
To select a custom pro-
gram, press the Custom
Programs button repeat-
edly until “P 3” or “P 4”
appears in the Distance/
Calories display.
Note: If the custom program has not yet been
defined, three columns of indicators will scroll
across the matrix. If more than three columns
of indicators scroll across the matrix, see HOW
TO USE A CUSTOM PROGRAM on page 17.
Press the Start button or the Speed increase
button and program the desired speed and in-
cline settings.
Amoment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Refer to the matrix. Each custom program is di-
vided into one-minute periods. One speed setting
and one incline setting
can be programmed for
each period. The speed
setting for the first period
is shown in the flashing
Current Period column of
the matrix. (The incline settings are not shown in
the matrix.) To program a speed setting and an in-
cline setting for the first period, simply adjust the
speed and incline of the treadmill as desired by
pressing the Speed and Incline buttons. Every few
times a Speed button is pressed, an additional in-
dicator will appear or disappear in the Current
Period column.
When the first period of the program ends, a se-
ries of tones will sound and the current speed set-
ting and the current incline setting will be saved in
memory.
The three columns of indicators will then
move one column to the left, and the speed set-
ting for the second period will be shown in the
flashing Current Period column. Program a speed
setting and an incline setting for the second period
as described above.
Continue programming speed and incline settings
for as many periods as desired; custom programs
can have up to forty periods. When you are fin-
ished with your workout, press the Stop button
twice. The speed and incline settings that you have
programmed and the number of periods that you
have programmed will then be saved in memory.
When you are finished exercising, remove the
key.
See step 8 on page 14.
4
3
2
1
Current Period

17
HOW TO USE A CUSTOM PROGRAM
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
Select a custom program.
To select a custom pro-
gram, press the Custom
Program button repeat-
edly until “P 3” or “P 4”
appears in the
Distance/Calories dis-
play. When a custom program is selected, the
maximum incline setting of the program will flash
in the Incline/Pulse display for a few seconds, the
maximum speed setting will flash in the Speed
display, and the program time will appear in the
Time/Pace display. A profile of the speed settings
of the program will scroll across the matrix.
Note: If only three columns of indicators scroll
across the matrix, see HOW TO CREATE A
CUSTOM PROGRAM on page 16.
Press the Start button or the Speed increase
button to start the program.
Amoment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Each custom program is divided into several one-
minute periods. One speed setting and one incline
setting are programmed for each period. Note: The
same speed setting and/or incline setting may be
programmed for two or more consecutive periods.
The speed setting for the
first period will be shown
in the flashing Current
Period column of the ma-
trix. (The incline settings
are not shown in the ma-
trix.) The speed settings for the next three periods
will be shown in the columns to the right.
When only three seconds remain in the first period
of the program, both the Current Period column
and the column to the right will flash, a series of
tones will sound, and the speed setting and the in-
cline setting will flash. When the first period ends,
all speed settings will move one column to the left .
The speed setting for the second period will then
be shown in the flashing Current Period column,
and the treadmill will automatically adjust to the
second speed and incline settings that you pro-
grammed previously.
The program will continue in this way until the
speed setting for the last period is shown in the
Current Period column and the last period ends.
The walking belt will then slow to a stop.
If desired, you can redefine to the program while
using it. To change the speed or incline setting
for the current period, simply press the Speed or
Incline buttons. When the current period ends, the
new setting will be saved in memory. To increase
the length of the program, first wait until the pro-
gram is completed. Then, press the Start button and
program speed and incline settings for as many ad-
ditional periods as desired. When you have added
as many periods as desired, press the Stop button
twice. To decrease the length of the program,
press the Stop button twice at any time before the
program is completed.
To stop the program temporarily, press the Stop
button. To restart the program, press the Start but-
ton or the Speed increase button.
Follow your progress with the displays.
See step 5 on page 13.
Measure your heart rate if desired.
See step 6 on page 14.
Turn on the fan if desired.
See step 7 on page 14.
When you are finished exercising, remove the
key from the console.
See step 8 on page 14.
7
6
5
4
3
2
1
Current Period

18
THE INFORMATION MODE/DEMO MODE
The console features an information mode that keeps
track of the total number of miles or kilometers that the
walking belt has moved and the total number of hours
that the treadmill has been operated. The information
mode also allows you to select miles or kilometers as
the unit of measurement and to turn on and turn off the
demo mode.
To select the information mode, hold down the Stop
button while inserting the key into the console, and
then release the Stop button. When the information
mode is selected, the following information will be dis-
played:
The Distance/Calories display
will show the total number of
miles or kilometers that the
walking belt has moved.
The Time/Pace display will
show the total number of
hours that the treadmill has
been used.
An “E” for English miles or an
“M” for metric kilometers will
appear in the Speed display.
Press the Speed increase but-
ton to change the unit of mea-
surement, if desired.
IMPORTANT: If a “d” appears
in the Incline/Pulse display, the
console is in the “demo” mode.
This mode is intended to be
used only when a treadmill is
displayed in a store. When the
console is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the indicators in the display will automatically light
in a preset sequence, although the buttons on the con-
sole will not operate. If a “d” appears when the infor-
mation mode is selected, press the Speed decrease
button so the “d” disappears.
To exit the information mode, remove the key from the
console.

19
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be per-
manently damaged. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) to raise,
lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the treadmill by the plastic foot rails.
Make sure you bend your legs and keep your back
straight. As you raise the treadmill, make sure to lift with
your legs rather than your back. Raise the treadmill about
halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the frame until the catch passes the
latch pin, and then slowly release the latch knob. Make sure
that the catch is held securely by the latch pin, as
shown.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sun-
light. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the catch is held
securely by the latch pin.
1. Hold one handrail with one hand, and place your other hand
on the deck. Place one foot against one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To re-
duce the risk of injury, use extreme caution while mov-
ing the treadmill. Do not move the treadmill over an un-
even surface.
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position. Base
Handrails
Deck
Wheels
Engaged
Catch
Storage
Latch
Frame

20
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill with your right hand as shown. Pull the
latch knob to the left and hold it. Pivot the treadmill down until
the frame is past the latch pin.
2. Hold the metal frame firmly with both hands,and lower the
treadmill to the floor. CAUTION: To decrease the possibility
of injury, do not lower the treadmill by gripping only the
plastic foot rails. Do not drop the treadmill frame to the
floor. Be sure to bend your legs and keep your back
straight.
Frame
Storage
Latch