Pro-Lift G5 Series User manual





ThankyouforpurchasingaPro‐LIFTG5.ThePro‐LIFTproductlineisdesignedtoenhanceyour
interactivewhiteboardsandprojectorsorLCD.Pleasefollowallassemblyinstructionscorrectlyto
provideoptimaluse.
OnlyaqualifiedcontractorshouldinstallthePro‐LIFTG5.Ifyoudonotunderstandanyoftheassembly
instructions,pleasecontactyourlocalre‐sellerorvisitwww.proliftstand.com.
IMPROPERINSTALLATIONCANCAUSEDAMAGETOYOURPro‐LIFTANDLEADTOSERIOUSPHYSICAL
INJURY.JOROManufacturingcannottakeanyresponsibilityfordamageorinjuryresultingfrom
improperinstallation.
DonotoperatePro‐LIFTG5ifthereareanyobstructionsbeloworabovethe
board.Doingsomaycauseunitmalfunctionorleadtoseriousphysicalinjury.
ThesuppliedmountinghardwareisforuseonthePro‐LIFTstandsonly.Ifyouencounteranyproblems
orinsufficienthardwareduringinstallation,pleasecontactyourlocalre‐seller.

ProLift G5 - G5L ASSY Instructions : 0.004
WB Fastener Kit
(ONLY available with G5W & G5W-PRO Models)
LCD Mount Fastener Kit
(ONLY available with G5L & G5L-PRO Models)
Note: Parts may not be exactly as shown and not to scale
5/32" Allen (Hex) Key
1x
2x
Board Backer Support
M6 x 12mm Socket Cap Screw SILVER
10x
JORO Button Head
8x
8x
M6 x 20mm Socket Cap Screw Low Profile
5/16 Hex Nut
8x
M6 Hex Nut
4x
1/4" Washer
4x
5/16" Washer
4x
M6 x 8mm Socket Cap Screw
16x 18x
M6 x 20mm Socket Cap Screw Low Profile
5/16x1" SILVER Button Head
4x
JORO Button Head
16x
5/16x1-1/2" Button Head
8x
G5 Main Frame Kit
5/32" Allen (Hex) Key
1x
Nylon Washer
6x
Machine Screw Insulator
6x
8x
M6 x 20mm Socket Cap Screw Low Profile
3/16" Allen (Hex) Key
1x
Wire Mgmt Molding
2x
M5 Allen (Hex) Key
1x
3/16" T-Handle Allen Key
5/32" Allen (Hex) Key
1x
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

For ease of installation, do this step while Pro-LIFT G5 is lying down
Be sure to NOT over tighten
Mount the Pro-LIFT G5 Feet
ProLift G5 - G5W ASSY Instructions : 0.003
Pro-LIFT G5 Foot
Pro-LIFT G5 Foot
5/16x1-1/2" Button Head
Be sure to use the 5/16x1-1/2" Button Head screws provided
1
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

Turret Head
ProLift G5 - G5W ASSY Instructions : 0.003
Mount the Turret Head
Be sure to NOT over tighten
If necessary, loosen 5/16x1" Button Head screws to align holes
REMEMBER to tighten screws, but DO NOT over tighten
5/16x1" Button Head
5/16x1" Button Head
5/16x1" Button Head
5/16x1" Button Head
M6 x 20mm Socket Cap Screw
Be sure to use the M6 x 20mm Socket Cap Screws (Low Profile) provided
2
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

Pro-LIFT G5 Accessory Shelf
Part#: WF122412PROL
Mount the Pro-LIFT G5 Accessory Shelf
Be sure to NOT over tighten
ProLift G5 - G5W ASSY Instructions : 0.003
If necessary, loosen 5/16x1-1/2" Button Head screws to align holes
REMEMBER to tighten screws, but DO NOT over tighten
5/16x1-1/2" Button Head
5/16x1-1/2" Button Head
M6 x 20mm Socket Cap Screw
Be sure to use the M6 x 20mm Socket Cap Screws supplied
3
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

ProLift G5 - G5W ASSY Instructions : 0.003
Mount the Pencil Tray Adapters (may not be exactly as shown)
Do not completely tighten fasteners until pencil tray has been fastened
Be sure to NOT over tighten
M6 x 20mm Socket Cap Screw
1/4" Nylon Washer
Machine Screw Insulator
Machine Screw Insulator
1/4" Nylon Washer
M6 x 20mm Socket Cap Screw
Be sure to use the following supplied parts:
1. M6 x 20mm Socket Cap Screw
2. 1/4" Nylon Washer
3. Machine Screw Insulator
4
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

Mount the WB Hanger
BE AWARE the mounting position of the WB Hanger is dependant on projector/white
board combination
Be sure to use the following supplied parts:
Be sure to NOT over tighten
ProLift G5 - G5W ASSY Instructions : 0.003
Once the WB Hanger is installed, thighten the 5/16x3/4" SILVER Button Head screws
5/16x3/4" SILVER Button Head screw
Be sure to tighten on both angles
once WB Hanger has be installed.
M6 Hex Nut
M6 x 20mm Socket Cap Screw
1/4" Washer
1/4" Washer
M6 Hex Nut
M6 x 20mm Socket Cap Screw
WB Hanger (SL-607)
Part#: G5-ACC-WBH
1. M6 x 20mm Socket Cap Screw
2. 1/4" Washer
3. M6 Hex Nut
5
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

5/16" Nylon Locking Nut
5/16" Washer
3/8" Nylon Washer
3/8" x 4" Lg. - 5/16" Hex Socket Head Shoulder
3/8" Washer
If the 3/8" x 4" Lg. - 5/16" Hex Socket Head Shoulder bolt is not fastened,
follow the sequence above
Laptop Tray Arm
Laptop Tray Slider Arm
M6x8mm SILVER Button Head
Fasten the Laptop Tray Arm to the Laptop Tray Slider Arm using
the M6x8mm SILVER Button Head Screws supplied
ProLift G5 - G5W ASSY Instructions : 0.003
Mount the Laptop Tray Arm (if the Laptop Tray was ordered with your product)
Be sure to NOT over tighten
6
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

Be sure to use the fasteners from the LTT Kit
Laptop Tray
Mount the Laptop Tray (if ordered with your product)
Be sure to NOT over tighten
ProLift G5 - G5W ASSY Instructions : 0.003
M6x8mm SILVER Button Head
M6x8mm SILVER Button Head
7
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

Fasten projector to the corresponding holes using the
JORO Button Head Screws supplied
ProLift G5 - G5W ASSY Instructions : 0.003
Mounting patterns for tested projectors
Match holes in the diagram to projection system being used
Be sure to NOT over tighten
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
8

Remove the backing from the
double sided tape and attach to
outer edge of upright
JORO recommends attaching the
Board Backer Supports supplied
Mount the white board
Use the holes which correspond to manufacturers
recommended projector to image distance
Be sure to NOT over tighten
Note, there are drilled/tapped holes on the frame
upright, if lowering the board is required
Mount the Board Backer Support Remove the backing from the double
sided tape and attach to side of frame
upright
ProLift G5 - G5W ASSY Instructions : 0.003
Board Backer Support
Laptop Tray (if ordered with your product)
Mount the Wire Mgmt Molding
JORO recommends attaching the
Wire Mgmt Moldings supplied
Wire Mgmt Molding
JORO Button Head
Fasten using the JORO Button Head screws supplied
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
9



10

For ease of installation, do this step while Pro-LIFT G5 is lying down
Do NOT over tighten
Mount the Pro-LIFT G5 Feet
ProLift G5 - G5L ASSY Instructions : 0.004
5/16x1-1/2" Button Head
Use the 5/16x1-1/2" Button Head screws provided
Pro-LIFT G5 Foot
Pro-LIFT G5 Foot
1
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

ProLift G5 - G5L ASSY Instructions : 0.004
Mount the Pro-LIFT G5 Accessory Shelf
Do NOT over tighten
M6 x 20mm Socket Cap Screw
Use the M6 x 20mm Socket Cap Screws supplied
If necessary, loosen 5/16x1-1/2" Button Head screws to align holes
REMEMBER to tighten screws, but DO NOT over tighten
5/16x1-1/2" Button Head
5/16x1-1/2" Button Head
Pro-LIFT G5 Accessory Shelf
Part#: WF122412PROL
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
2

Remove Pro-LIFT LCD Arms
ProLift G5 - G5L ASSY Instructions : 0.004
5/16x1" SILVER Button Head
5/16x1" SILVER Button Head
Pro-LIFT LCD ARM
Remove 5/16x1" SILVER Button Head screws and store in safe
place to re-use once LCD is installed.
Remove Pro-LIFT LCD Arms
Pro-LIFT LCD ARM
Pro-LIFT LCD ARM
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
3

ProLift G5 - G5L ASSY Instructions : 0.004
Be sure to NOT over tighten
5/16 Hex Nut
5/16x1" SILVER Button Head
When fastened end result should resemble this
G5-ACC-PT5
5/16 Hex Nut
5/16 Hex Nut
5/16x1" SILVER Button Head
5/16 Hex Nut 5/16x1" SILVER Button Head
5/16x1" SILVER Button Head
Fasten the 5/16x1" SILVER Button Head screws to the G5-ACC-PT5
G5-ACC-PT5
5/16x1" SILVER Button Head
5/16x1" SILVER Button Head
5/16 Hex Nut
5/16 Hex Nut
5/16 Hex Nut
5/16x1" SILVER Button Head
5/16x1" SILVER Button Head
5/16 Hex Nut
4
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com

600 VESA 800 VESA 600 VESA 400 VESA 200 VESA 200 VESA 400 VESA 800 VESA
Do NOT over tighten
Use the appropriate fasteners as specified in the LCD owners manual
Fasten the G5-ACC-PT5 to your LCD (not included) using the
fasteners from the LCD TV Kit.
Please use the appropriate mounting holes for your
LCD (not included) as shown above
ProLift G5 - G5L ASSY Instructions : 0.004
LCD fastener from
LCD TV kit provided
G5-ACC-PT5
G5-ACC-PT5
COPYRIGHT 2014
www.proliftstand.comwww.joromfg.com
5