Pro-Lift WMHS-WB User manual





ThankyouforpurchasingaProͲLIFTWMHS.TheProͲLIFTproductlineisdesignedtoenhanceyour
interactivewhiteboardsandprojectorsorLCD.Pleasefollowallassemblyinstructionscorrectlyto
provideoptimaluse.
OnlyaqualifiedcontractorshouldinstalltheProͲLIFTWMHS.Ifyoudonotunderstandanyofthe
assemblyinstructions,pleasecontactyourlocalreͲsellerorvisitwww.proliftstand.com.
IMPROPERINSTALLATIONCANCAUSEDAMAGETOYOURProͲLIFTANDLEADTOSERIOUSPHYSICAL
INJURY.JOROManufacturingcannottakeanyresponsibilityfordamageorinjuryresultingfrom
improperinstallation.
DonotoperateProͲLIFTWMHSifthereareanyobstructionsbeloworabovethe
board.Doingsomaycauseunitmalfunctionorleadtoseriousphysicalinjury.
ThesuppliedmountinghardwareisforuseontheProͲLIFTstandsonly.Ifyouencounteranyproblems
orinsufficienthardwareduringinstallation,pleasecontactyourlocalreͲseller.

WB Fastener Kit
(ONLY available with WMHS-LCD Models)
Note: Parts may not be exactly as shown and not to scale
(ONLY available with WMHS-WB Models)
LCD Mount Fastener Kit
WMHS Main Frame Kit
M6x12mm SILVER Button Head
10x
Machine Screw Insulator
6x
WMHS - WMHS-WB ASSY Instructions : 0.004
16x
M6 x 8mm Socket Cap Screw
Wire Mgmt Molding
4x
JORO Button Head
16x
5/16 Hex Nut
8x
Head Self Tapping Screw #12 x 2" Slotted Washer
12x
M6 Hex Nut
4x
Nylon Washer
6x
3/16" Allen (Hex) Key
1x
2x
#8 x 3/4" Pan Head Wood Screw
5/16" Washer
4x
5/16x1" Button Head
4x
M5 Allen (Hex) Key
1x
JORO Button Head
8x
5/32" Allen (Hex) Key
1x
4x
Thread-Cutting Screw (8-32 x 3/8" Lg.)
8x
M6 x 20mm Socket Cap Screw Low Profile
2x
Nylon Cable Clip 5/16''
2x
Nylon Cable Clip 1/4''
1/4" Washer
4x
18x
M6 x 20mm Socket Cap Screw Low Profile
5/32" Allen (Hex) Key
1x
5/32" Allen (Hex) Key
1x
Board Backer Support
2x
2x
#8 Zinc Wall Anchor
JORO Button Head
8x
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

WMHS - WMHS-WB ASSY Instructions : 0.004
For ease of installation, do this step prior to mounting WMHS
Carefully ease out the power cable and switch assembly through panel window
Be sure to NOT pull with excessive force
Switch Assembly
Power Cable - Male End
Panel Window
1
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

Be sure to fasten Sacrificial Surface to at least three joists
WMHS - WMHS-WB ASSY Instructions : 0.004
Sacrificial Surface
(recommended
3/4" thick)
Min.
35.5 Recommended
" Ceiling Height96
Recommended
24
Min.24
Recommended
2
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

WMHS - WMHS-WB ASSY Instructions : 0.004
Mark out the two screw locations to hang the WMHS
Pre-drill pilot holes at the two locations
Be sure both points are horizontal and level
Slotted Hex Washer Head Screw
Fasten the two Slotted Hex Washer Head Screws in the pre-drilled holes
Allow3/8"Min.distance
fromsacrificialsurfaceto
hangWMHS
Slotted Hex Washer Head Screw
Slotted Hex Washer Head Screw
(recommendedfor8'ceiling)
54
20.625
3
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

Slotted Hex Washer Head Screw
WMHS - WMHS-WB ASSY Instructions : 0.004
Slotted Hex Washer Head Screw
Add the Slotted Hex Washer Head Screws to upper flat bar
(3 per either side of WMHS is recommended)
Temporarily plug in WMHS and raise the mechanism to
access upper flat bar slots
Be sure previous steps are completed and WMHS is
securely fastened to wall prior to operation
Be sure WMHS is securely fastened to wall by tightening all
Slotted Hex Washer Head Screw
Lower mechanism back to lowest position and unplug
before continuing to next step
Slotted Hex Washer Head Screw
Add the Slotted Hex Washer Head Screws to lower flat bar
(2 per either side of WMHS is recommended)
MUST fasten Slotted Hex Washer Head Screws
through the hole on the flat bar to prevent sliding
Be sure WMHS is securely fastened to wall by tightening
all Slotted Hex Washer Head Screws
Hang the WMHS on the two
Slotted Hex Washer Head Screw
4
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

WMHS - WMHS-WB ASSY Instructions : 0.004
Mount the WB Hangers (WMHS-ACC-WBH)
Be sure to NOT over tighten
BE AWARE the mounting position of the WB Hanger is dependant on projector/white
board combination
WMHS-ACC-WBH
M6 x 8mm Socket Cap Screw
Be sure to use the M6 x 8mm Socket Cap Screw screws provided
WMHS-ACC-WBH
UpperMountingPosition
LowerMountingPosition
5
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

Mount the Turret Head
Be sure to NOT over tighten
WMHS - WMHS-WB ASSY Instructions : 0.004
M6 x 8mm Socket Cap Screw
Be sure to use the M6 x 8mm Socket Cap Screws provided
6
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

WMHS - WMHS-WB ASSY Instructions : 0.004
Power bar can be mounted on the other WMHS-ACC-WBH, if required
Be sure to NOT over tighten
Mount the Power Bar (may already be installed)
JORO Button Head
Be sure to use a cable strain relief loop using Nylon Cable Clip 5/16''
Nylon Cable Clip 5/16''
1/4 External Tooth Lock Washer
1/4 External Tooth Lock Washer
WMHS-ACC-WBH
Cable Strain Relief Loop
Be sure to use the JORO Button Head Screws and External Tooth
Washers provided
WMHS-ACC-WBH
WMHS-ACC-WBH
7
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

Mounting position dependant on manufacturers instructions
Mount the Pencil Tray Mounts (WMHS-ACC-PTM)
Be sure to NOT over tighten
WMHS - WMHS-WB ASSY Instructions : 0.004
WMHS-ACC-PTM
M6 x 8mm Socket Cap Screw
WMHS-ACC-PTM
Be sure to use the M6 x 8mm Socket Cap Screw Screws provided
WMHS-ACC-PTM
Loosely fasten the M6 x 8mm Socket Cap Screws to allow
WMHS-ACC-PTM to slide once white board has been hung
8
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

WMHS - WMHS-WB ASSY Instructions : 0.004
Mounting patterns for tested projectors
Match holes in the diagram to projection system being used
Be sure to NOT over tighten
Fasten projector to the corresponding holes using the
JORO Button Head Screws supplied
9
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

Remove the backing from the
double sided tape and attach to
outer edge of upright
JORO recommends attaching the
Board Backer Supports supplied
Be sure to NOT over tighten
Use the holes which correspond best
to the pencil tray brackets
Fasten the Pencil Tray Brackets
WMHS - WMHS-WB ASSY Instructions : 0.004
Lower
drilled/tapped
holes
JORO Button Head
Fasten using the JORO Button Head screws supplied
Mount the white board
Use the holes which correspond to manufacturers
recommended projector to image distance
Be sure to NOT over tighten
Note, there are drilled/tapped holes on the mounting
plate, if lowering the board is required
Mount the Wire Mgmt Molding
JORO recommends attaching the
Wire Mgmt Moldings supplied
Remove the backing from the double
sided tape and attach to side of frame
upright
Wire Mgmt Molding
Mount the Board Backer Support
Board Backer Support
Board Backer Support
JORO Button Head
JORO Button Head
Fasten using the
JORO Button Head screws supplied
JORO Button Head
JORO Button Head
10
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

WMHS - WMHS-WB ASSY Instructions : 0.004
JORO Button Head
M6x6mm Button Head
To Heighten
To Lower
Adjusting Turret Head IF NECESSARY
JORO Button Head
M6x6mm Button Head
Loosen JORO Button Head Screws 1 turn each side
Be sure re-tighten JORO Button Head Screws - DO NOT OVER TIGHTEN!
Adjust the M6x6mm Button Head Screws accordingly

11
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

Mount the Switch Assembly
Be sure to use the fasteners and accessories supplied
Be sure to NOT over tighten
Mount the Cable Clamp for wire management
Be sure to run the switch wire through the
cable clamp prior to fasteneing
Switch can be mounted on either side of frame
Be sure to NOT over tighten
WMHS - WMHS-WB ASSY Instructions : 0.004
Thread-Cutting Screw (8-32 x 3/8" Lg.)
Nylon Cable Clip 1/4''
#8 Zinc Wall Anchor
Washer
#8 x 3/4" Pan Head Wood Screw
12
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com



13

2x
Nylon Cable Clip 1/4''
5/16x1" SILVER Button Head
4x
1/4" Washer
4x
Nylon Washer
6x
2x
#8 Zinc Wall Anchor
JORO Button Head
8x
WB Fastener Kit
(ONLY available with WMHS-LCD Models)
Note: Parts may not be exactly as shown and not to scale
(ONLY available with WMHS-WB Models)
LCD Mount Fastener Kit
WMHS Main Frame Kit
M6x12mm SILVER Button Head
10x
5/32" Allen (Hex) Key
1x
JORO Button Head
16x
5/32" Allen (Hex) Key
1x
WMHS - WMHS-LCD ASSY Instructions : 0.006
2x
#8 x 3/4" Pan Head Wood Screw
3/16" Allen (Hex) Key
1x
Machine Screw Insulator
6x
4x
Thread-Cutting Screw (8-32 x 3/8" Lg.)
18x
M6 x 20mm Socket Cap Screw Low Profile
JORO Button Head
8x
Head Self Tapping Screw #12 x 2" Slotted Washer
12x
Board Backer Support
2x
5/16" Washer
4x
8x
M6 x 20mm Socket Cap Screw Low Profile
5/32" Allen (Hex) Key
1x
2x
Nylon Cable Clip 5/16''
5/16 Hex Nut
8x
16x
M6 x 8mm Socket Cap Screw
M5 Allen (Hex) Key
1x
M6 Hex Nut
4x
Wire Mgmt Molding
4x
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com

WMHS - WMHS-LCD ASSY Instructions : 0.006
For ease of installation, do this step prior to mounting WMHS
Carefully ease out the power cable and switch assembly through panel window
Do NOT pull with excessive force
Switch Assembly
Power Cable - Male End
Panel Window
1
COPYRIGHT 2017
www.proliftstand.comwww.joromfg.com