Pro-Line II CT42R3 User manual

CT42R3 (MAHOGANY), CT42R7 (CHERRY) CONFERENCE TABLE
OPERATING INSTRUCTIONS
WARNING
1. Do not use this product unless all screws and bolts are
securely tightened.
2. Check that all screws and bolts are tight every three
months or as needed.
3. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
4. Do not use this product as a stepladder.
5. Use this product for its intended purpose only.
PROLINE II CONFERENCE TABLE LIMITED WARRANTY
ProLine II conference tables are warranted from the date of purchase against failure due to material and workmanship as follows:
• 5 years structural integrity
• 3 years on wood nishes
Grain, color and finishes
Variation of grain and color are natural, inherent characteristics of wood, a living material. This variation is part of the beauty of
real wood and anticipated in wood veneer furnishings. Therefore, ProLine II Furniture is not warranted to match in grain or color
or texture. It is a natural phenomenon for wood grain to change in color as it ages, and wood nishes are not warranted for color-
fastness.
Warranty Exclusions
This warranty will not cover labor, freight, or damage from misuse, abuse, negligence, alteration, assembly, installation, attachments,
accident, vandalism, acts of nature or any other event beyond the control of Ofce Star Products. The warranty does not cover
cosmetic damage that may result from normal use. Liability for incidental or consequential damage is excluded. The user assumes
all risk of injury resulting from use of this product.
This warranty applies only to products purchased through authorized Ofce Star Products ProLine II dealers and products sold
within the United States of America and the Commonwealth of Canada. This warranty does not apply to products used for rental
purposes. This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.

© Office Star Products March 2008
PART QTY
1. Top Panel ...................1
2. Large Leg Frame ..............1
3. Small Leg Frame ..............2
4. Cam Lock ..................14
5. Cam Lock Stud ..............14
6. Wooden Dowel . . . . . . . . . . . . . . . 4
7. Plastic Cap .................14
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert two Wooden Dowels (6) into each side of Large Leg Frame (2), screw in three Cam Lock Studs (5) into each side of Large Leg Frame (2)
AS SHOWN IN DETAIL A, align Small Leg Frames (3) with Large Leg Frame (2) and attach, secure using six Cam Locks (4) and
FULLY TIGHTEN CAM LOCKS (4) USING PHILLIPS SCREWDRIVER (not provided), AS SHOWN IN DETAIL B.
STEP 2 Place Top Panel (1) face down on a soft surface, screw in eight Cam Lock Studs (5) into bottom of Top Panel (1), FULLY TIGHTEN CAM
LOCK STUDS (5) USING PHILLIPS SCREWDRIVER (not provided). Align assembled leg frames to attached Cam Lock Studs (5) of Top
Panel (1) and secure using eight Cam Locks (4), FULLY TIGHTEN CAM LOCKS (4) USING PHILLIPS SCREWDRIVER (not provided).
Cover holes in table using fourteen Plastic Caps (7).
ATTENTION: MAKE SURE ALL CAM LOCKS ARE FULLY TIGHTENED BEFORE USING TABLE.
IMPORTANT NOTE:
1. Use hand tools only for assembly as power tools may cause damage
2. Carefully remove any staples used for packaging.
Phillips Screwdriver also needed for
assembly (not provided)
STEP 1
STEP 2
DETAIL A
DETAIL B
DETAIL C
1
2
3
4
5
6
3
54
CT42R3 (MAHOGANY), CT42R7 (CHERRY) CONFERENCE TABLE
ASSEMBLY INSTRUCTIONS
7
7