Proflex Vb100 User manual

VIBRATION

PLATFORM MACHINE

VB100

Colours may vary

User Manual

[Revision 2.0 March 2020]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by

this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Vibration Platform Machine – VB100

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

•Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

•Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

•Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

•Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

•Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

•This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

•Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

•Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

•The equipment is designed for domestic

use only.

•Handle the equipment safely and carefully.

•Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

•Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

•Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

•Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

•The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and care,

see Equipment Safety.

Vibration Platform Machine – VB100

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

•Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and safety

codes.

•Wherever possible, use a residual current

device (RCD).

•High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

•Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

•Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift, move or

carry equipment.

•Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

•Do NOT attempt any maintenance or repair

work not described in this manual.

•After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories or performing repair or

maintenance.

•Do NOT adjust while the equipment is

running.

•Perform service related activities in suitable

conditions, such as a workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Vibration Platform Safety

Basic precautions, including the following important safety instructions should always be followed when using the machine. Read all instructions

before use.

To reduce the risk of electric shock, always unplug the machine from the electrical outlet after use and before cleaning, assembling, or servicing.

Failure to follow these instructions may lead to personal injury and cause damage to the machine.

Before beginning any exercise program, consult your physician. This is especially important for people over 35 years of age or who have pre-

existing health problems. Read all instructions before using any fitness equipment.

WARNING! To reduce the risk of burns, fire, electric shock or injury, read the following:

•Use this product for its intended use only as described in this user manual. Do not use attachments not recommended by the manufacturer.

•Never operate the unit with a damaged cord or plug, or if it is not working properly. If it has been dropped, damaged or exposed to water, have

the unit inspected/repaired by an authorised service centre.

•Caution – To avoid injury, use caution when stepping on to or off the machine.

•Maximum weight capacity = 180kg

•Do not attempt any maintenance or adjustments other than those described in this user manual. Should any problems arise, discontinue use and

consult an authorized service centre or personnel.

•Never operate the appliance with the air openings blocked. Keep the air openings free of lint, hair, and other obstructions.

•Do not use the unit outdoors.

•Do not pull the unit by its power cord or use the cord as a handle.

•Keep children and pets away from the equipment while in use.

•Elderly or disabled users should only use the unit in the presence of an adult who can provide assistance if required.

•Do not operate where aerosol (spray) products are in use or where adequate oxygen is not available.

•Keep dry – do not operate in wet or moist conditions.

•The motor cover can become hot while the unit is in use. Do not place the unit on a flammable surface as this can create a fire hazard.

•Keep electrical cord away from hot surfaces.

•Keep the unit on a solid, level surface with a minimum safety area clearance of two meters around it. Be sure the area around the treadmill

remains clear of any obstructions during use.

•The machine is for domestic household use only.

•Only one person should use the machine at a time.

•Wear comfortable and suitable clothing when using the machine.

•Do not leave children unsupervised near or on the machine.

•Children should not be allowed to play or operate the machine at any time.

•To disconnect, turn all controls to the OFF position, then remove plug from the wall outlet.

•The machine is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

•This unit must be plugged into a nominal 240VAC / 50Hz grounded mains electrical outlet.

•Keep hands clear of all moving parts. Never place hands or feet under the machine while in use.

•If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

•Allow the machine to stop fully and unplug the power cord from the wall outlet before moving it.

Vibration Platform Machine – VB100

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Vibration Platform Machine – VB100

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Vibration Platform Machine – VB100

Table of Contents

Safety .............................................................................................................................................................2

Safety Symbols...........................................................................................................................................................4

Parts Identification .......................................................................................................................................7

Vibration Platform .......................................................................................................................................................7

Remote Control...........................................................................................................................................................7

Control Panel ..............................................................................................................................................................8

Operation.......................................................................................................................................................8

Program and Manual Modes ......................................................................................................................................8

Console and Functions...............................................................................................................................................8

Manual Mode Training................................................................................................................................................9

Setting Session Duration....................................................................................................................................10

Program Mode Training............................................................................................................................................10

Exercising .................................................................................................................................................................10

Exercise Positions..............................................................................................................................................11

Care, Troubleshooting and Maintenance .................................................................................................12

Cleaning and Maintenance.......................................................................................................................................12

Storage .....................................................................................................................................................................12

Troubleshooting ........................................................................................................................................................12

Specifications .............................................................................................................................................13

Vibration Platform Machine – VB100

Parts Identification

Vibration Platform

Remote Control

Note: Colours of vibration platform and remote may vary

Foot

Switch

Plug

Moving wheel

Foot pad

Foot

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Vibration Platform Machine – VB100

Control Panel

Operation

Program and Manual Modes

The vibration platform features two basic operating modes:

•Manual Mode – The machine is being used, but not running a pre-set program (see Program mode, below).

In this mode, the machine will continue for the duration of the countdown timer at the current speed until you

stop the machine, change the speed, timer etc. To enter Manual mode, turn the machine on, then press ON /

OFF.

•Program Mode – The machine runs through a pre-set routine where it will automatically apply several

speeds over the session duration. There are 10 pre-set routines to choose from ("P0" to "P9"). To enter

Program mode, turn the machine on, then press PROG MODE [Pon remote control]. Press repeatedly to

step through programs. At the desired program, press ON / OFF.

Console and Functions

The machine features a computerized display that provides you with controls

for operating the unit as well as workout information, such as duration, speed

etc.

To use the machine:

1. Plug the machine into a compatible electrical supply (1).

2. Place the power switch, located at the lower front of the unit, in the "ON"

("I") position (2).

3. Operate the machine as desired.

The machine is equipped with a remote control unit that replicates the console

functions. When using the machine, it may be easier to use remote control to

operate it.

Time -

Power ON

Auto mode

Start

Stop

Speed +

Speed -

Speed window

Remote control

Time window

Time +

2

1

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Vibration Platform Machine – VB100

Console/Remote Control

Function Description

Display Shows various sessions information, such as remaining time, program mode (if

selected) and animation.

ON / OFF (remote control) Press to switch the machine ON and OFF. Note that the main power switch [next to

the electrical lead] must be in the ON position.

PRG Mode / P (remote control)

When the machine is on but not running, press to enter Program mode. Press

repeatedly to step through programs. The current program number is shown in the

display.

Time- / T-(remote control)

Press to reduce the countdown timer by 1 minute. Press and hold to quickly decrease

the timer. The timer has a maximum of 10 minutes. The machine stops automatically

once the countdown timer reaches "00:00". The current countdown timer value is

shown in the display. Not applicable in Program mode.

Time + / T+ (remote control)

Press to increase the countdown timer by 1 minute. Press and hold to quickly increase

the timer. The default timer has a maximum of 10 minutes. The machine stops

automatically once the countdown timer reaches "00:00". The current countdown timer

value is shown in the display. Not applicable in Program mode.

Speed- / S-(remote control)

When the machine is running, press to decrease vibration speed by a value of 1.

Press and hold to quickly change speed. The speed range is 1 to 180. The current

speed setting is shown in the display. Not applicable in Program mode.

Speed + / S+ (remote control)

When the machine is running, press to increase vibration speed by a value of 1. Press

and hold to quickly change speed. The speed range is 1 to 180. The current speed

setting is shown in the display. Not applicable in Program mode.

P0-3 (remote control) Cycle between the P0, P1, P2 and P3 pre-set programs

P4-6 (remote control) Cycle between the P4, P5 and P6 pre-set programs

P7-9 (remote control) Cycle between the P7, P8 and P9 pre-set programs

30 (remote control) Sets the machine to level 30 speed

60 (remote control) Sets the machine to level 60 speed

99 (remote control) Sets the machine to level 99 speed

Manual Mode Training

The machine has a "manual" mode of operation, which gives you the freedom to adjust the vibration platform

operation as desired at any time.

1. Switch the machine ON.

2. Press ON / OFF. The machine starts running at the slowest speed setting.

3. Adjust speed using the speed adjustment controls as required.

4. When finished, press ON / OFF.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Vibration Platform Machine – VB100

Setting Session Duration

When training, the machine defaults the countdown timer to 10 minutes (this is the maximum timer value) to a

pre-set session duration, the machine stops automatically once the timer counts down to "00:00".

1. Switch the machine ON [but do not start it].

2. Press Time + / Time -as required. The current time in minutes is shown in the display. Duration can range

from 1 to 10 minutes.

3. Press ON / OFF.

4. When the timer finishes, the machine stops.

Program Mode Training

The machine has 10 automatic training programs, "P0" to "P9". Each program has a standard duration of 10

minutes and applies differing speeds several times per program. To access the programs:

1. Turn on the machine [but do not start it], press PRG MODE [Pon remote control] to select program 1 ("P0"

displays). To select other programs, keep pressing PRG MODE as required.

2. Press ON / OFF.

3. When the program completes, the machine stops.

Exercising

The vibration platform uses muscular reflex of the body to exercise in a convenient manner that does not require

you to get out of breath. The machine accomplishes this best when you are in a stressed position, such as a

squat posture, and your muscles are working to keep you in that position. When the oscillating plate moves

quickly, your muscles automatically move a small amount to maintain posture, resulting in efficient muscular

exercise.

The vibration platform provides effective exercise, but only if you use it in the recommended exercise positions.

You will get the best results if you bend your knees or arms (depending on exercise position) and push against

the machine platform so your muscles adopt the automatic motion described. Use several different postures for

a few minutes each for a complete workout.

You can also use the vibration platform as a general massager to ease muscle pain and improve circulation. In

this case, do not push hard against the machine, rather let the machine do the work for you.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Vibration Platform Machine – VB100

Exercise Positions

General Muscle Toning

Stand on the platform and place your

feet apart, in line with your shoulders.

This position helps improve overall

circulation and muscle tone.

Leg and Thigh

Stand on the platform and place your

feet apart, in line with your shoulders,

then squat down so your knees are at

approximately 90° and hold this

position. This position provide a thigh

workout.

Upper Body

Kneel in front of the

machine and place your

hands on the platform, in

line with your shoulders.

This position provides

an upper body workout.

For further muscle training, lean forward and bend

your arms to approximately 90° and hold this position.

Lower Leg

Sit in front of the

machine and

place your calves

on the platform,

supporting your

body with your hands behind you. For further

muscle training, lift your bottom off the floor and

press your legs harder against the platform.

Waist

Stand in front of the

machine, with legs placed

apart, then place your

hands on the platform. For

further muscle toning,

bend your arms, pressing

harder against the platform

and hold the position.

Legs and Buttocks

Stand in front of the machine,

then place one leg on the

platform and remain relaxed.

For further muscle toning,

lean forward, pressing harder

against the platform and hold

the position.

Buttocks

Sit on the platform, with your

buttocks at the centre. Remain

relaxed and keep your back

straight.

Feet

Sit on a chair and place

your feet on the platform.

This helps ease tension

and improve circulation.

Further to the normal vibration platform exercise, the machine is equipped

with resistance bands that you can use to add additional muscular exercise

to your workout sessions. Attach the resistance bands to the brackets on the

underside of the platform.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Vibration Platform Machine – VB100

Care, Troubleshooting and Maintenance

To prevent electrical shock, switch off and unplug the machine before cleaning or performing

routine maintenance.

Cleaning and Maintenance

The machine can be cleaned with a soft cloth and mild detergent. Do not use abrasives or solvents. Be careful

not to get excessive moisture on the control panel as this may damage it and create an electrical hazard.

After each use, wipe the unit of any sweat, dirt or liquids.

Storage

Store the machine in a clean and dry indoor environment. Never leave or use the unit outdoors. Ensure the

master power switch is OFF ("O") and the power cord is un-plugged from wall outlet.

Troubleshooting

Problem Potential Reason Correction

Machine will not start. Machine not plugged in. Plug power cord to electrical outlet and

switch ON.

No console display. No connection. Check electrical cables are in good

condition and properly connected.

Remote control not

functioning.

A. Remote control not aimed at receiver.

B. Batteries.

A. Point the remote towards the machine

console when in use.

B. Use new batteries [2 x AAA size].

When to Call for Help

The vibration platform is designed with user safety as a priority. In the event of electrical failure, the machine will

shut off automatically to prevent injury and damage to the unit. If you encounter unusual behaviour from the

vibration platform, turn the power switch off and on to reset the machine. This should ready the machine for

normal operation again. If after you have reset the machine that it is still not operational, call an authorised

service centre or technician for servicing.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Vibration Platform Machine – VB100

Specifications

Speed Levels 99

Training Programmes 10

Voltage 240V

Frequency 50/60Hz

Weight Capacity 180kg

Remote Control Yes

Resistance Bands Yes

Power Plug Australian Standard

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Proflex VB100 User manual

Popular Fitness Equipment manuals by other brands