Body Craft F711 User manual

Open your Camera App
and point it at the QR
Code for additional
information.
http://www.bodycraft.com/
U1000-U1K1-qr.html
Owner’s Manual
1
Base Lot Number: _ _ _ _ _ _ _ _ _ _ _ _ _
Purchased Date: ___ / ___ / ______
Dealer’s Name:__________________________
Please register your products at:
https://www.bodycraft.com/product-registration/
To see this manual in
FULL COLOR
scan this QR code.
F711 Leg Extension/Curl Attachment
Open your Camera
App and point it at
the QR Code
To see in
FULL COLOR
& addition information,
scan this QR code
Serial Number
Assembled Parts List
F711 v1.4
Part # Assembly Parts List QTY
F711-001-ASM LEG WEIGHT HOLDER - Assembly 1
F711-002 ADJUST TUBE 1
F711-003 FOAM ROLLER HOLDER 3
F711-004 FOAM ROLLER 6
F711-005 LARGER END CAP 6
F711-006 SMALLER END CAP 6
F711-007 NUT CAP 2
F711-008 SPRING CLIP 1
F711-009 LOCKING PIN, L-TYPE 1
F711-020 RUBBER CUSHION 1
Part # Assembly Hardware QTY
F711-010
HEX RECESSED HEAD BOLT, 5/16" x 1-1/4"
- BLK 6
F711-011 FLAT WASHER, 1/2" - BLACK 2
F711-012 HEX BOLT, 1/2" x 3-1/4" - BLACK 1
F711-013 BIG WASHER, φ8 - BLACK 6
F711-014 NYLON NUT, THICK, 1/2" - BLACK 1

Product Assembly
STEP 1a: Leg Weight Holder
Attach the ADJUST TUBE (2) onto the LEG WEIGHT HOLDER - Assembly (1-ASM) using:
● One HEX BOLT, 1/2" x 3-1/4" (12)
● Two FLAT WASHERS, 1/2" (11)
● One NYLON NUT, THICK, 1/2" (14).
Once fully tightened with movement in parts, see TIP below, then install both NUT CAPS (7).
TIP: Fully tighten HEX BOLT (12)
then loosen the locking NYLON
NUT, THICK (14) approximately 1/4
turn so that the LEG WEIGHT
HOLDER - Assembly (1-ASM) &
ADJUST TUBE (2) pivot freely with
little to no excessive movement
1. Attach LEG WEIGHT HOLDER(112) onto
ADJUST TUBE(111), using HEX HEAD
BOLT(151), two 1/2" WASHER(153) and NYLON
NUT(152).
2. Insert FOAM ROLLER HOLDER(113) into the
ADJUST TUBE(111) and LEG WEIGHT
HOLDER(112).
3. Slide FOAM ROLLER(131) onto each side of
FOAM ROLLER HOLDER(131).
4. Attach END PLUGS(123) to FOAM ROLLER
HOLDER(113) and attach 50 SQ. END
PLUG(122) to ends of LEG WEIGHT HOLDER(112).
5. Slide RUBBER BUMPER(125) onto WEIGHT
HOLDER(112). The SPRING CLIP(142)
is used to hold weight plates on WEIGHT
HOLDER(122).
6. L PIN(143) is used to lock LEG WEIGHT
HOLDER(112).
STEP 1b: Foam Roller Holders
Insert all three FOAM ROLLER HOLDERS (3)
into the ADJUST TUBE (2) and the LEG
WEIGHT HOLDER - Assembly (1-ASM).
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove
all packing materials from your area and place them back into the box. Do not dispose of the
packing materials until assembly is completed.
Read each step carefully before beginning.
3/4 SOCKET &
6” EXTENSION
3/4 WRENCHES
Recommended Tools
9/16 SOCKET &
6” EXTENSION
9/16 WRENCHES
Recommended Tools
2

4 ft-lbs
(+/- 1 lbs)
4 ft-lbs
(+/- 1 lbs)
Product Assembly
Please Hand Tighten All Bolts Until end of STEP 2
STEP 1a: Main Frame
Attach Rear Stabilizer (4) to Main
Frame (1) using two Hex Bolts (14),
four Flat Washers (10) and two Thick
Nylon Nuts (12).
1. Attach LEG WEIGHT HOLDER(112) onto
ADJUST TUBE(111), using HEX HEAD
BOLT(151), two 1/2" WASHER(153) and NYLON
NUT(152).
2. Insert FOAM ROLLER HOLDER(113) into the
ADJUST TUBE(111) and LEG WEIGHT
HOLDER(112).
3. Slide FOAM ROLLER(131) onto each side of
FOAM ROLLER HOLDER(131).
4. Attach END PLUGS(123) to FOAM ROLLER
HOLDER(113) and attach 50 SQ. END
PLUG(122) to ends of LEG WEIGHT HOLDER(112).
5. Slide RUBBER BUMPER(125) onto WEIGHT
HOLDER(112). The SPRING CLIP(142)
is used to hold weight plates on WEIGHT
HOLDER(122).
6. L PIN(143) is used to lock LEG WEIGHT
HOLDER(112).
STEP 2a: Install Foam Rollers
Slide END CAP, LARGER (5) then the FOAM
ROLLER (4) onto each side of FOAM ROLLER
HOLDER (3), one bar post at a time.
NOTE: Confirm centered with equal distance on both
Rt & Lt Sides.
STEP 2b: Secure Foam Rollers
Then slide a HEX RECESSED HEAD
BOLT, 5/16" x 1-1/4" (10) through the
END CAP, SMALLER (6) and the BIG
WASHER, φ8 (13).
Then secure by tightening the HEX
RECESSED HEAD BOLT, 5/16" x 1-1/4"
(10) to the FOAM ROLLER HOLDER (3)
per side. Repeat to the other FOAM
ROLLER HOLDERS.
STEP 2c: Accessories
Attach RUBBER CUSHION (20), SPRING
CLIP (8) and RING PIN (9).
TIP: Recommended Tools
7/32 Allen Wrenches x 2ea.
STEP 2d: “Torque Time”
Tighten STEP 2a & 2b, HEX RECESSED HEAD BOLTS
(10) at this time to the Recommended Torque Specs of
4 ft-lbs (+/-1 lb).
3
4 ft-lbs
(+/- 1 lbs)

Parts Exploded View & Detailed Parts List
INSERT LOCKING PIN WHEN NOT USING
THE LEG EXTENSION/CURL.
Part # Detailed Parts List QTY
F711-001 LEG WEIGHT HOLDER 1
F711-002 ADJUST TUBE 1
F711-003 FOAM ROLLER HOLDER 3
F711-004 FOAM ROLLER 6
F711-005 LARGER END CAP 6
F711-006 SMALLER END CAP 6
F711-007 NUT CAP 2
F711-008 SPRING CLIP 1
F711-009 LOCKING PIN, L-TYPE 1
F711-010
HEX RECESSED HEAD BOLT, 5/16" x 1-1/4"
- BLK 6
F711-011 FLAT WASHER, 1/2" - BLACK 2
F711-012 HEX BOLT, 1/2" x 3-1/4" - BLACK 1
F711-013 BIG WASHER, φ8 - BLACK 6
F711-014 NYLON NUT, THICK, 1/2" - BLACK 1
F711-015 BUSHING 2
F711-016 END PLUG, 50 x 50mm SQ. 3
F711-017 BUMPER 1
F711-018 ROUND CAP 1
F711-019 SET SCREW, 5/16" x 1/2" 2
F711-020 RUBBER CUSHION 1
4