Progress Lighting AirPro GULLIVER User manual

GULLIVER Ceiling Fan Installation Manual
93099818 _A
P250012

Limited Lifetime W a rranty
Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so
long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to
be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic
blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of
any sea coast. Extended warranties for ENERGY STAR® qualified products may apply.
Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are
warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance
with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for
fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical
components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no
warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.
D ate Pu r ch as ed
Sto r e Pu r ch as ed
Mo d el N o .
Ser ial N o .
With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for
replacement. After 30 days, the original purchaser MUST contact Progress Lighting at [phone] for repair or replacement
which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.
Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not
limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.
This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or
neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without
limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or
attempted) or failure to provide maintenance to the fan.
THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND
ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS
LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR
CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NONINFRINGEMENT.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or
consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights
and you may have other rights which vary from state to state.
Vendor N o .
UPC
111041

Safety Rules.....................................................................................................................................................................................
1.
Unpacking Your Fan ....................................................................................................................................................................... 2.
Installing Your Fan ..........................................................................................................................................................................
3.
Operating Your Transmitter ............................................................................................................................................................ 7.
Care of Your Fan ............................................................................................................................................................................
9.
Troubleshooting
...............................................................................................................................................................................
10.
Specifications
..................................................................................................................................................................................
11.
T a ble ofContents

1. To reduce the risk of electric shock, insure electricity has been turned off
at the circuit breaker or fuse box before beginning.
2. All wiring must be in accordance with the National Electrical Code and
local electrical codes. Electrical installation should be performed by a
qualified licensed electrician.
3. WARNING: To reduce the risk of electrical shock and fire, do not use
this fan with any solid-state fan speed control device.
4. WARNING: To reduce the risk of fire, electric shock, or personal injury,
mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.)
Or Less" and use mounting screws provided with the outlet box. Most outlet
boxes commonly used for the support of light fixtures are not acceptable for
fan support and may need to be replaced. Due to the complexity of the
installation of this fan, a qualified licensed electrician is strongly
recommended.
8. To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
9. Do not use water or detergents when cleaning the fan or fan blades. A
dry dust cloth or lightly dampened cloth will be suitable for most
cleaning.
10. After making electrical connections, spliced conductors should be
turned upward and pushed carefully up into the outlet box. The wires
should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box.
11. Electrical diagrams are for reference only. Light kits that are not packed
with the fan must be UL Listed and marked suitable for use with the
model fan you are installing. Switches must be UL General Use
Switches. Refer to the Instructions packaged with the light kits
WARNING
TO REDUCE THE RISK OF
WARNING
PERSONAL INJURY,
DO NOT BEND THE
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT.
5. The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.
Use only UL-listed outlet boxes marked FOR FAN SUPPORT.
6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from
the bottom of the fan guard to the floor.
7. Avoid placing objects in the path of the blades.
1.
S afety R ules
BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.
NOTE
READ AND SAVE ALL INSTRUCTIONS!

Unpack your fan and check the contents. You should have the following items:
8. Loose parts bag containing:
1. Canopy assembly
2. Ball/downrod assembly
3. Fixture assembly
4. LED bulbs (3)
5. Receiver
6. Transmitter
7. 9V battery
a. Mounting hardware Wire nuts (6)
Unpacking
Your Fan 2.
MED LOW
HI OFF
ON DIP
1 2 3 4
1
23
5
6
47

Tools Required
Phillips screw driver, straight slot screw driver,
adjustable wrench, step ladder, and wire cutters.
Mounting
Options
If there isn't an existing cUL listed mounting
box, then read the following instructions.
Disconnect the power by removing fuses or
turning off circuit breakers.
Outlet box
Angled ceiling
maximum
18.5
angle
Recessed
outlet box
Provide strong support
Ceiling
hanger
bracket
Secure the outlet box directly to the building
structure. Use appropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the
fan (at least 35 lbs). Do not use plastic outlet
boxes.
Figure 1 Figure 3
Note: You may need a longer downrod to
maintain proper clearance when installing on a
steep, sloped ceiling.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR OTHER PERSONAL INJURY,
MOUNT FAN ONLY TO AN OUTLET BOX
MARKED ACCEPTABLE FOR FAN SUPPORT
AND USE THE MOUNTING SCREWS
PROVIDED WITH THE OUTLET BOX. OUTLET
Figure 2
Outlet box
Figure 4
Outlet box
BOXES COMMONLY USED FOR THE
SUPPORT OF LIGHTING FIXTURES MAY NOT
BE ACCEPTABLE FOR FAN SUPPORT AND
MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
3. Installing
Your Fan
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4
(available at your Progress Lighting Retailer).

Hanging the Fan
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 1. Insert the end of downrod (B) through
the connector (PP),align the two holes in the
downrod (B) and the connector (PP).(Fig.5)
Step 2. Insert a plug pin (GG) through the two
holes in the downrod (B) and the connector (PP).
(Fig.5)
Step 3. Insert the R-shaped pin (HH) though the
hole near the end of the plug pin (GG) until it
snaps into its locked position. (Fig.5)
Step 4. Install the screw (FF) to the connector
(PP), and make sure it’s tighten. (Fig.5)
Step 5. Insert the canopy (C) and metal cover
(D) through the downrod (B). (Fig.6)
Step 6. Insert the hanger ball (J) through the
downrod (B), and then insert a plug pin (L)
through the hole in the downrod (B). (Fig.6)
Step 7. Insert the plug pin to the slot cut off in
the hanger ball (J) until it snaps into its locked
position. (Fig.6)
Step 8. Install the Hanger bracket (A) on the
outlet box by using the washer and screws are
provided with the junction box. (Fig.7)
Step 9. Put the hanger ball (J) through the open
side of the ceiling mounting bracket, and then
insert the hanger ball to the slot cut off in the
ceiling mounting bracket. (Fig.7)
4.

Make the Electric
Connections
WARNING: To avoid possible electrical
shock, be sure electricity is turned off at the
main fuse box before wiring.
CODE SWITCH: Codes are set by pushing dip
switches up or down. It is imperative that the
code used for both transmitter and receiver is
exactly the same, otherwise remote controller
will not work. Please note the code switch will
enable you to operate a second remote
controller independently. For example, if you
have two ceiling fans with 2 remote control
units, set 2 different codes for each set of
transmitter/receivers. This means you can
operate each ceiling fan independently.
Your remote control is ready for use after
battery installation. (Fig.8)
Step 1. Fan motor to Receiver Electrical and
Current Limiter Connections: Connect the
Black wire from the fan to Black wire marked
"TO MOTOR L". Connect the White wire from
the fan to the White wire marked "TO
MOTOR N" from the receiver and the White
wire from the Current limiter. Connect the
blue (light) wire to the black wire from the
Current Limiter. Connect the Red wire from the
Current Limiter to the Blue wire from the
Receiver. Secure wire connections with the
plastic wire nuts provided. (Fig. 9)
Step 2. Receiver to House Supply Wires
Electrical Connections: Connect the black (hot)
wire from the ceiling to the black wire
marked "AC in L" from the receiver.
Connect the white (neutral) wire from the
ceiling to the white wire marked "AC in N"
from the Receiver. Secure the wire connections
with the plastic wire nuts provided. (Fig. 9)
Step 3. If your outlet box has a ground wire
(green or bare copper) connect it to the fan
ground wires; otherwise connect the hanging
bracket ground wire to the mounting bracket.
Secure the wire connection with a plastic nut
provided. After connecting the wires spread
them apart so that the green and white wires are
on one side of the outlet box and black and blue
wires are on the other side. Carefully tuck the
wire connections up into the outlet box. (Fig.
9)
ON DIP
1 2 3 4
Blue(for light)
Black
(for Fan motor)
Blue(to light)
Black
("to Fan motor L")
White(neutral)
White
("to Fan motor N")
Receiver
Outlet box
Green
Green (ground)
White ("AC IN N")
Black ("AC IN L")
Black (hot) White(neutral)
Fan motor
Figure 9
Red
Black
White(neutral)

5.
An additional safety support is provided to
prevent the fan from falling. Secure the safety
cable to the ceiling joist with screw and washer.
(Fig. 10)
Step 4. Once the connection has been made,
the receiver inserts into the drop rod hanging
bracket. The canopy comes up to cover the
receiver and bracket. (Fig. 11)
Installing the canopy:
Step 1. Align the locking slots of the canopy
(C) with the two screws (FF) in the mounting
bracket (A). Push up to engage the slots and to
lock in place. (Fig. 12)
Step 2. Rotate the metal cover (D) clockwise
to lock in the bottom of the canopy. (Fig. 12)
Installing metal mesh and bulbs:
Step 1. Insert the fan blades (M) onto the shaft
(U), install lock nut (Q) onto the fan shaft after
the blade assembly (M) is installed. (Fig. 13)
Step 2. Screw light bulbs (F) into the fixture
sockets. (Fig. 13)
Step 3. Align the locking slots of the metal
grill (G) with three Knurled screw (H) in the
fixture (E). Push up to engage the slots and to
lock in place. (Fig. 13)
#8 X 1-1/2 Screw
Figure 10
Spring washer
Flat washer
Safety cable
ON DIP
1 2 3 4
HANGER
BRACKET
RECEIVER
Figure 11
CANOPY
A
C
FF
D
Figure 12
E
F
G
H
M
Q
U
Figure 13

6.

FUNCTIONS OF TRANSMITTER:
OFF : Turn off the ceiling fan.
HI : Turn on the fan at high speed.
MED : Turn on the fan at medium speed.
LOW : Turn on the fan at low speed.
LIGHT : ON/OFF- Press and release
immediately to turn on or off the light.
DIMMER(If any)- Press and hold on to dimmer
or brighten the light.
7. Operating
Your Transmitter
Installation of Transmitter
Wall Mount Holder with two
screws.

The Reverse switch is located on the motor housing.
Slide the switch to the Left for warm weather
operation. Slide the switch to the Right for cool
weather operation. (Fig. 13)
NOTE: Wait for fan to stop before changing the
setting of the slide switch.
Speed settings for warm or cool weather depend on
factors such as the room size, ceiling height, number of
fans, etc.
Warm weather - (Forward) A downward air flow
creates a cooling effect as shown in Figure 14. This
allows you to set your air conditioner on a higher
setting without affecting your comfort.
Cool weather - (Reverse) An upward airflow moves
warm air off the ceiling area as shown in Figure 15.
This allows you to set your heating unit on a lower
setting without affecting your comfort.
Disassembling Your Fan
This fan comes with a pre-assembled blade and front
guard for your easy installation. Check that all screws
are tight and securely in place.
Use a lint free lightly damp cloth or duster to remove
dust from the blades.
Figure 15
Figure 16
8.
E
F
G
H
M
Q
U
Figure 14

Here are some suggestions to help you maintain your
fan
1. Because of the fan's natural movement, some
connections may become loose. Check the support
connections, brackets, and blade attachments
twice a year. Make sure they are secure. (It is not
necessary to remove fan from ceiling.)
2. Clean your fan periodically to help maintain its new
appearance over the years. Use only a soft brush or
lint-free cloth to avoid scratching the finish. The
plating is sealed with a lacquer to minimize
discoloration or tarnishing. Do not use water when
cleaning. This could damage the motor, or the wood,
or possibly cause an electrical shock.
3. Cover small scratches with a light application of
shoe polish.
4. There is no need to oil your fan. The motor has
permanently lubricated bearings.
IMPORTANT
MAKE SURE THE POWER IS OFF AT THE
ELECTRICAL PANEL BOX BEFORE YOU
ATTEMPT ANY REPAIRS. REFER TO THE
SECTION "MAKING ELECTRICAL
CONNECTIONS"
9. Care of
Your Fan

Problem
Fan will not start.
Fan sounds noisy.
Remote control
malfunction
Solution
1. Check circuit fuses or breakers.
2. Check line wire connections to the fan and switch wire connections in the switch housing.
CAUTION: Make sure main power is
off.
3. Check to make sure the dip switches from the transmitter and receiver are set to the same frequency.
4. Check the battery in the transmitter.
1. Make sure all motor housing screws are snug.
2. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.
CAUTION: Make sure main power is
off.
3. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this time.
4. Check that light bulb is also secure.
5. Some fan motors are sensitive to signals from solid-state variable speed controls. If you have installed this type of control,
choose and install another type of control.
6. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.
1. Do not connect the fan with wall mounted variable speed control (s).
2. Make sure the dip switches are set correctly.
Troubleshooting 10.

Size Speed Volts
Fan Power
Consumption
(without
lights) WATT
Airflow
CFM
Airflow
Efficiency
(Higher Is
Better)
CFM/WATT
Net
Weight Gross Weight Cubic Feet
14in. Low 120
22.93
873.41
38.01
24.8 lb
(11.27kg) 28.76 lb (13.06kg) 5.89cu.
Ft.
Medium
31.95
1099.56
34.41
High
39.05
1297.28
32.99
These are approximate measures. They do not include Amps and Wattage used by the light kit.
c 2018 Progress Lighting, Inc.
701 Millennium Blvd.,
Greenville, SC 29607
All Rights Reserved
11. Specifications