progressive automations FLT-09 User manual

Page 1 of 7
FLT-09
The FLT-09 is a three leg table lift set with a 25.5” stroke size and 110 lbs of force per leg.
This model comes with a power supply and an interactive remote with up to four
programmable preset functions. It comes with everything needed for installation. Table top
is not included.
TABLE LIFT SET - 3 LEG - 3 STEP - STROKE SIZE 25.5
HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com

Page 2 of 7
CAUTION/INFORMATION
USE/LIABILITY
HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com

Page 3 of 7
HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com
PARTS

HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com
ASSEMBLY INSTRUCTIONS
STEP 3
Slide the Side Brackets (4) into both Frames (5). Attach the
brackets using four M6x14 Machine Screws (9).
Page 4 of 7
STEP 1
Attach the 120° Frames (7,8) to one of the Legs (3) as
shown in the picture below. Line up the holes on the Leg
with the holes on the Frames.
Use the supplied Allen Wrench to insert four M6x10
Machine Screws (10) through the holes on the Frame
(7,8) going into the Leg (1). Rotate each screw just a few
turns until all four are inserted, then tighten them.
STEP 2
Place one of the Legs (3) into one of the Frames (5)
and line up the holes.
Use the supplied Allen Wrench to insert four M6x10
Machine Screws (10) through the holes on the Frame
(5) going into the Leg (3). Rotate each screw just a
few turns until all four are inserted, then tighten
them. Do the same for the other Leg and Frame.
STEP 4
Slide the Center Rails (6) into the 120° Frames (7,8) and
attach them into position using sixteen of the M6x10
Machine Screws.

Page 5 of 7
ASSEMBLY INSTRUCTIONS
HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com
STEP 5
Attach each Foot (2) to the two end Legs (3) with
four M6x14 Machine Screws and tighten them.
Attach a Glide (1) to each foot and the middle
Leg.

HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com
DIMENSIONAL DRAWING
75.3"
43.4"
49"
23.5"
22.6"
2"
27.5"
1.2"

Page 6 of 7
OPERATIONAL PROCEDURE
HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com
Once your table lift is installed it is simple to operate. Just use the wired remote for full up/down motion
control. Use the up button to raise the table lift and use the down button to lower it.
You can preset up to 4 positions by following this simple procedure: Use the up/down buttons on the
remote to find your desired height(s), then press “M” followed by a number 1-4., then wait a few seconds
until the height is displayed again. To move to the set position, hold the number button.
Once a preset button is pushed, the desk will move to the programmed height. Make sure no obstacles
are in the table lifts path and that it is not touching any walls.
RESET PROCEDURE
IMPORTANT
You must reset the desk prior to use:
To reset you must push and hold the DOWN button on the Hand Remote (7) until the table lift reaches its
lowest point. Release the DOWN button. Press and hold the DOWN button again until the LED display
shows "RST". If you are not using an LED hand remote hold it for about 10 seconds. Release the DOWN
button. Finally Press and hold the DOWN button once more until the table lift lowers, slightly rises then
stops. Release the DOWN button and your table lift is now ready to use.

Page 7 of 7
Height Range 23.5” - 49” (without desktop)
Base Width 43.4” min. - 75.3” max.
Travel Speed 1.5” per second (no load)
Weight Capacity 330 lbs.
Duty Cycle 10% Max. 2 mins on, 18 mins off
Features Soft start/stop
Adjustable leveling studs
4 Memory presets
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com
Minimum Table Top Size 43"x 24”
If your table lift is not functioning it might need to be reset. Follow the RESET procedure
from page 6.
If your hand remote has an LED display and it displays "RST" (reset), perform the reset
procedure from page 6.
If the LED displays shows an error message ("Er1" - "Er13"), confirm that all wired
connections are secure. Then peform the reset procedure from page 6.
If the error message persists after the reset procedure, contact us at 1-800-676-6123 or
[email protected].
If the height between the legs exceeds 1.5", stop the reset procedure and contact us.
If the LED remote displays "HOT", let the base cool down for 20 minutes.

SETTING UPPER & LOWER LIMITS
Upper Limit
To set the upper limit, use the UP/DOWN buttons to move the table lift to your desired
max height position. Once it is at the desired position, press and hold the "M" until the
LED display flashes "S-" once, then release the button. Press and release the button two
more times in quick succession. The LED display should then show "999" on the third
press and then automatically return to the desired height. The upper limit is now set.
Lower Limit
To set the upper limit, use the UP/DOWN buttons to move the table lift to your desired
minimum height position. Once it is at the desired position, press and hold the "M" until
the LED display flashes "S-" once, then release the button. Press and release the button
two more times in quick succession. The LED display should then show "000" on the third
press and then automatically return to the desired height. The lower limit is now set.
Removing Limits
To remove the upper and lower limits, use the UP/DOWN buttons to move the desk to
any desired position. Press and hold the "M" button until the LED display flashes "S-"
once, then release the button. Press and release the button in succession until the display
changes to "555"(ignore any other readings). After a few seconds, the display will
automatically change back to the numbered height position. Upper and lower limits should
now be removed.
*After the upper and lower limits are set, the previous memory positions (1,2,3,4) may be
outside the new range of movement. If this happens, simply reset the memory positions.
*A Reset procedure requires the desk base to fully retract beyond any lower limit. Please
ensure you have proper clearance below the desk base.
*If you attempt to revise a previously set upper or lower limit and it is outside of the
existing range, you will need to remove the original upper/lower limits first.
HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com

HOW TO ORDER 1.800.676.6123 | [e-mail] | www.progressiveautomations.com
Press the DOWN button on the Hand Remote until the base reaches its lowest position.
Measure the height of the base from the floor and if the number on the LED display does
not match your measurements, follow the steps below:
Press and hold the DOWN button again until the LED display reads "RST".
Press and hold the "M" button for about 5 seconds until the LED displays the flashing
starting height.
To change the value of the starting height:
Increase by 0.1s, press the UP button
Decrease by 0.1s, press the DOWN button
Increase by 1s, press the "1" button
Decrease by 1s, press the "2" button
Increase by 10s, press the "3" button
Decrease by 10s, press the "4" button
Once the new value is displayed, wait about 5 seconds and the display will return to
"RST". Finish the reset process by pressing and holding the DOWN button again until
the desk lowers a little bit more, slightly rises and stops. Release the DOWN button and
the new starting height value is saved.
MODIFIYING LED DISPLAY