progressive automations FLT-04 User manual

FLT-04
User Manual
Page 2
Page 3
Page 4
Page 5
Caution/Liability
Technical Specifications
Parts
Assembly Instructions
Setup
Operational/Reset Procedure,
Troubleshooting
Dimensions
Page 6
Contents
Page 7
Page 8-9

Caution
Liability
2

Technical Specifications
3
Duty Cycle 10% Max. 2 mins on, 18 mins off
Height Range 23.5” - 49” (without table top)
Minimum Table Top Size 43"x 24”
Weight Capacity 700lbs (175 lbs Per Leg)
Features Soft start/stop, adjustable leveling studs & 4 memory presets
Input Voltage 120 VAC, 60 Hz
Output Voltage 24 VDC
Stroke 25.5"
Speed 1.50"/sec
Material Steel
Certification UL

Parts
4
Leg Stand-Off
Wood Screw
M5x20
Wood Screw
M5x16 Control Box
Switch Power Cable LC Cable (59") Cable Clip Glide (Prenstalled) x4
Machine Screw
M6x14 VT Bracket
Noise Attenuation
Pad x16
x4 x4 x24 x6
x1
x32 x4
x15

STEP 1
Lay out all the included components and hardware
to ensure you have everything listed on the parts page.
Take four of the self-adhesive Noise Attenuation Pads (P5)
and place them on the VT Brackets (P4) as shown.
STEP 2
Place the VT Brackets (P4) on the underside of the
surface you will be lifting. Use the included 24 Wood
Screws (P13) to attach the Brackets in place, using six
screws per bracket.
STEP 6
Now that everything’s in place we can start connecting it
all together. Connect the remote (P8) to the Control Box
(P6). Use the 4 LC Cables (P9) to connect each Leg
(P1) to the Control Box (P6). Finally take the Power
Cable (P11) and connect each one to the control box.
Use the included adhesive-backed Cable Clips (P15) to
secure all the wires so they don’t get tangled.
STEP 7
Once you have everything connected and secure,
carefully turn your surface right-side-up. We recommend
using at least 2 people to do this. Adjust the pre-installed
Glides (P3) as needed.
STEP 8
Plug the Power Cable (P11) from the Control Box (P6)
into an outlet.
IMPORTANT
You MUST reset the table lift prior to use. See Reset
Procedure on page 7.
STEP 3
Place the 4 Legs (P1) into the 4 VT Brackets (P4) as shown.
Using the supplied Allen Wrench, loosely thread the M6X14
Machine Screws (P12) into the remaining holes on each of the
VT Brackets (P4) to secure the 4 legs (P1). Once all screws are in
place, fully tighten all four screws.
STEP 4
Now that the Legs (P1) are secure you can attach the 4 Stand-
Offs (P2) and 4 Glides (P3) to the bottom of each leg as shown.
Secure the Stand-Offs (P2) and Glides (P3) with the remaining
M6X14 Machine Screws (P12), 4 per leg.
STEP 5
Attach the Control Box (P6) to the underside of your surface using
two of the M5X16 Screws (P14) per box. Make sure you leave
enough room for cable connections into the wire ports
on the box. Next find a suitable area to place your Remote (P8),
we recommend somewhere on the end of your surface along the
front edge. Once you’re happy with its position you can attach it
using 2 x M5X16 Screws.
Assembly Instructions
5
Caution: Double-check that the wood screws
(P13) are short enough that they won’t puncture a
hole in your surface when screwed in completely
If your surface is not pre-drilled we recommend
you pre-drill any holes needed for the VT Brackets
(P4). Never use countersunk screws
As stated earlier make sure the screws are short
enough that they don’t puncture a hole in your
surface when screwed in completely. Do not
overtighten the screws here, overtightening may
cause damage to the components.
Ensure the box and remote are placed so the
wires can reach between everything

Setup
6
FLT-04
CONTROL BOX
HS
M4
M3
WIRED REMOTE
FLT-04 Leg
[M1,M3]
FLT-04 Leg
[M2,M4]
M2
M1
110VAC AC

7
If your lifting columns are not functioning it may require a reset. Follow the RESET procedure.
If your hand remote has an LED display and it displays "RST" (reset), perform the reset procedure.
If the LED displays shows an error message ("Er1" - "Er13"), confirm that all wired connections are
secure. Then perform the reset procedure.
If the LED remote displays "HOT", let the unit cool down for 20 minutes.
If the error message persists after the reset procedure, contact us at 1-800-676-6123 or
[email protected]
Operational Procedure
Once your lift columns are installed, operation is simple. Using the wired remote will allow full control over
extending and retracting the lift columns. Use the up button to raise the column lifts and the down button to lower
the column lifts.
You can program up to 4 locations using the memory setup: Use the up/down buttons on the remote to find your
desired height(s), then press “S” followed by a number 1-4. The column heights position is now saved. To move to
the set position, hold the number button.
Reset Procedure
IMPORTANT
You must reset the lifting columns prior to use:
If the lifting columns are not functioning properly or the LED screen displays “RST” or “Er1” - “Er13”, please
follow the reset procedure: Unplug the power cord and lifting columns for 30 seconds. Plug the lifting columns
into the control box ensuring a secure connection then plug the power cord in before continuing to the next step.
If the columns lifts are raised at all, press and hold the DOWN button on the remote until the lifting columns are
fully retracted. Press and hold the DOWN button for 10 seconds until the LED display reads “ASr”. If you are
using a spare remote without an LED, hold the DOWN button for 10 seconds.
Once “ASr” is displayed on the remote, press and hold the down DOWN until the lifting columns lower, slightly
rise, then stop. Release the button and the table lift is now ready to use.
Troubleshooting

Dimensions
8
1.9"
1.4" 0.8"
0.6"
2.8" 1.6"
Ø1.8"
Ø0.4"
0.4"
0.2"
1.3"
2.8" 2.4"
0.6"
3.5"
7.1" 6.5"
0.8"
3.4"
6.3"
0.6" 6.4"
5.1"
1.0"
6.1"
7.1"
0.1"
0.1"
Ø0.25"
Ø0.20"
1.9"
0.1"
Legs
Brackets
Stand-Offs
22.0"
3.8"
1.7"
0.5"
6.5"
7.0"
2.0" 3.2"
0.5"
1.0"
M6X10

Dimensions
9
Control Box
Wired Remote
AC
HS M1 M2 M3
1.8"
5.8"
0.6"
0.5"
AC
M4
M1 M2 M3 M4
HS
10.1"
5.8"
Ø0.2
0.6000
M
34
2
1
˄˅
5.7"
3.3"
2.0"
3.4"
2.2"
1.4" 0.2"