ProLights Mosaico FX100FC Series User manual

USER MANUAL
REV.01-05/23 English version
Mosaico FX100FC
100W RGBW IP66 modular LED image projec-
tor with dual effect wheel and one gobo slot
(PRELIMINARY)

Thank you for choosing PROLIGHTS
Please note that every PROLIGHTS product has been designed in Italy to meet quality and performance requirements
for professionals and designed and manufactured for the use and application as shown in this document.
Any other use, if not expressly indicated, could compromise the good condition/operation of the product and/or be
a source of danger.
This product is meant for professional use. Therefore, commercial use of this equipment is subject to the respectively
applicable national accident prevention rules and regulations.
Features, specications and appearance are subject to change without notice. Music & Lights S.r.l. and all afliated
companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or any other
loss occasioned by the use of, inability to use or reliance on the information contained in this document.
Product user manual can be downloaded from the website www.prolights.it , or can be inquired to the ofcial
PROLIGHTS distributors of your territory (https://www.prolights.it/sales_network.html).
Scanning the below QR Code, you will access the download area of the product page, where you can nd a broad
set of always updated technical documentation: specications, user manual, technical drawings, photometrics,
personalities, xture rmware updates.
The PROLIGHTS Logo, PROLIGHTS names and all other trademark in this document pertaining to PROLIGHTS services
or PROLIGHTS product are trademarks OWNED or licensed by Music & Lights S.r.l., its afliates, and subsidiaries.
PROLIGHTS is a registered trademark by Music & Lights S.r.l. All right reserved. Music & Lights – Via A. Olivetti, snc -
04026 - Minturno (LT) ITALY.
Visit the download area
of the product page

PROLIGHTS - Mosaico FX100 01
INDEX
SAFETY INFORMATION 02
1 - PACKAGING 05
PACKAGE CONTENT..................................................................................................... 05
OPTIONAL ACCESSORIES............................................................................................. 05
2 - TECHNICAL DRAWING 06
3 - INSTALLATION 07
MOUNTING.................................................................................................................... 07
4 - CONNECTION TO THE MAINS SUPPLY 08
5 - START UP 08
CONNECT AND DISCONNECT POWER FROM THE PRODUCT.................................. 08
6 - PRODUCT OVERVIEW 09
7 - CONNECTION TO THE MAINS SUPPLY 10
8 - DMX CONNECTION 11
CONNECTION OF THE CONTROL SIGNAL: DMX LINE .............................................. 11
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION ............................................... 11
CONNECTION DAISY CHAIN OF THE DMX LINE ........................................................ 11
CONNECTION OF THE CONTROL SIGNAL: DMX LINE ADAPTERS ........................... 12
CONNECTION OF THE DMX LINE................................................................................ 12
CONSTRUCTION OF THE DMX TERMINATION ........................................................... 12
DMX ADDRESSING ........................................................................................................ 12
OPERATION AS A WIRELESS RECEIVER........................................................................ 13
CRMX TO DMX (RX) ....................................................................................................... 13
9 - CONTROL WITH PUSH ROTATORY KNOB 14
10 - SHORTCUT 15
11 - RDM MENU STRUCTURE 16
12 - RDM FUNCTIONS 18
13 - DMX CHARTS 23
14 - ANIMATION WHEEL / WATER EFFECT REPLACEMENT 28
15 - CUSTOM ANIMATION WHEEL 30
16 - COLOR FILTER AND GOBO MOUNTING 31
COLOR HOLDER / GOBO HOLDER (CODE MFX100CH - MFX100GH) ....................... 31
17 - GOBO SIZE 34
18 - ERROR MESSAGES 35
19 - ACCESSORIES INSTALLATION 36
LENS ACCESSORY ......................................................................................................... 36
SNOOT ACCESSORY ..................................................................................................... 37
ANTI TAMPERING FULL SNOOT WITH FRONT GLASS ACCESSORY .......................... 38
WALL BRACKET.............................................................................................................. 39
SURFACE BRACKET ....................................................................................................... 40
BRACKET FOR WALL MOUNTING AND SUSPENSION ON POLES (CODE
MOSUNIBRACKJR)......................................................................................................... 41
20 - TEST OF IP66 RATING 42
21 - MAINTENANCE 43
MAINTENANCE AND CLEANING THE PRODUCT........................................................ 43
REPLACING THE FUSE................................................................................................... 43
VISUAL CHECK OF PRODUCT HOUSING ..................................................................... 43
TROUBLESHOOTING..................................................................................................... 44

PROLIGHTS - Mosaico FX10002
SAFETY INFORMATION
WARNING!
• Please read carefully the instruction reported in this section before installing, power-
ing, operating or servicing the product and observe the indications also for its future
handling.
This unit is not for household use, only professional applications.
Connection to mains supply
• The Connection to the mains supply must be carried out by a qualied electrical installer.
• Use only AC supplies 100-240V 50-60 Hz, the xture must be electrically connected
to ground (earth).
• Select the cable cross section in according with the maximum current draw of the
product and the possible number of products connected at the same power line.
• The AC mains power distribution circuit must be equipped with magnetic+residual
current circuit breaker protection.
• Do not connect it to a dimmer system; doing so may damage the product.
Protection and Warning against electrical shock
• Do not remove any cover from the product, always disconnect the product from AC
power before servicing.
• Ensure that the xture is electrically connected to ground (earth). And use only a
source of AC power that complies with local building and electrical codes and has
both overload and ground-fault (earth-fault) protection.
• Before using the xture, check that all power distribution equipment and cables are
in perfect condition and rated for the current requirements of all connected devices.
• Isolate the xture from power immediately if the power plug or any seal, cover, cable, or
other components are damaged, defective, deformed or showing signs of overheating.
• Do not reapply power until repairs have been completed.
• Refer any service operation not described in this manual to PROLIGHTS Service team
or an authorized PROLIGHTS service center.
Installation
• Make sure that all visible parts of the product are in good visible condition before its
use or installation.
• Make sure the point of anchorage is stable before positioning the projector.
• When suspending the xture above ground level, secure it against failure of primary
attachments by attaching a safety cable that is approved as a safety attachment for
the weight of the xture to the attachment point on the main frame of the product. ln
case the safety cable, enter in action, it needs to be replaced with a new one.
• Install the product only in well ventilated places.
• For non temporary installations, ensure that the xture is securely fastened to a load-
bearing surface with suitable corrosionresistant hardware.
• For a temporary installation with clamps, ensure that the quarter-turn fastener and/or
screws are turned fully, and secured with a suitable safety cable.
0,5 m Minimum distance of illuminated objects
• The projector needs to be positioned so that the objects hit by the beam of light are
at least 0,5 meters (1,64 ft) from the lens of the projector.
T
45°
C
a
Max operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) exceeds 45 °C (113 °F).

PROLIGHTS - Mosaico FX100 03
T
-20°
C
a
Minimum operating ambient temperature (Ta)
• Do not operate the xture if the ambient temperature (Ta) is below -20 °C (-4 °F).
Protection from burns and re
• The exterior of the xture becomes hot during use. Avoid contact by persons and
materials.
• Ensure that there is free and unobstructed airow around the xture.
• Keep ammable materials well away from the xture
• Do not expose the front glass to sunlight or any other strong light source from any an-
gle. Lenses can focus the sun’s rays inside the xture, creating a potential re hazard.
• Do not attempt to bypass thermostatic switches or fuses.
IP66
Permanent Outdoor use
• This product is rated with an IP (Ingress protection) for permanent outdoor use when
used and serviced according to the instruction contained in this document.
• Never use the xture in places subject to vibrations or bumps.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Excessive dust, smoke uid, and particle build up degrades performance, causes
overheating and will damage the xture.
• Damages caused by inadequate cleaning or maintenance are not covered by the
product warranty.
Light collimation optical system
• This product contains internal light collimation opticsl system. Avoid to expose the
optical system to any intense source of light (including sunlight) from any angle.
T 59°C
c
Temperature of the external surface
• The surface of the xture can reach up to 59 °C (138,2 °F) during operation. Avoid
contact with people and materials.
Maintenance
• Warning! Disconnect the xture from AC mains power and allow to cool for at least
10 minutes before handling.
• Only technicians who are authorized by PROLIGHTS or Authorised service partners
are permitted to open the xture.
• Users may carry out external cleaning, following the warnings and instructions pro-
vided, but any service operation not described in this manual must be referred to a
qualied service technician.
• Important! Excessive dust, smoke uid, and particle build up degrades performance,
causes overheating and will damage the xture. Damages caused by inadequate
cleaning or maintenance is not covered by the product warranty.
Photobiological safety
• This device emits potentially dangerous optical radiation and is identied in the cat-
egory of Risk Group 2 according to EN 62471.

PROLIGHTS - Mosaico FX10004
Do not stare at the operating light source
• Do not look directly at the LED source during operation. It can be harmful to the eyes
and skin.
• During Installation, operation and maintenance, be prepared for the xture to light
and move suddenly when connected to power.
• The device should be positioned so that prolonged staring into the luminaire at adis-
tance closer than 3,482 m (11,423 ft) is not expected.
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10.5 m
34.45 ft
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
10.5 m
34.45 ft
Minimun
distance
Risk
Group 2
Risk
Group 1
0.2 m
0.7 ft
3,482 m
11,423 ft
Disposal
• This product is supplied in compliance with European Directive 2012/19/EU – Waste
Electrical and Electronic Equipment (WEEE). To preserve the environment please dis-
pose/ recycle this product at the end of its life according to the local regulation.
The products to which this manual refers comply with:
• 2014/35/EU - Safety of electrical equipment supplied at low voltage (LVD).
• 2014/30/EU - Electromagnetic Compatibility (EMC).
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS).
• 2014/53/EU - Radio Equipment Directive (RED).
Other approvals

PROLIGHTS - Mosaico FX100 05
1 - PACKAGING
PACKAGE CONTENT
• 1x MOSAICOFX100FC.
• 1x MFX100CH: color holder for MOSAICOFX100FC serie (color lters not included).
• 1x MFX100GH: gobo holder for MOSAICOFX100FC serie (gobo not included) with manual index-
ing.
• 1x MFX100WE1: water effect wheel for MOSAICOFX100FC series, short axis 1.
• 1x MFX100WE2: water effect wheel for MOSAICOFX100FC series, long axis 2.
• 1x BARE END - IP connection adapter.
• 1x 5p XLR - IP connection male adapter.
• 1x 5p XLR - IP connection female adapter.
• User Manual.
OPTIONAL ACCESSORIES
• MFX100BAG1U: Pelican case for 1 pc of MOSAICOFX100FC
• MFX100WBRAKGY: Wall bracket for MOSAICOFX100FC, gray
• MFX100WBRAKBK: Wall bracket for MOSAICOFX100FC, black
• MFX100FBRAKGY: Surface bracket for MOSAICOFX100FC, gray
• MFX100FBRAKBK: Surface bracket for MOSAICOFX100FC, black
• MOSUNIBRACKJR: Bracket for MOSAICOJR for wall mounting and suspension on poles
• MFX100LWGN: 15° FLEX lens for Mosaico FX100 series, narrow beam angle for animation and
gobo
• MFX100LWTM: 30° lens for Mosaico FX100 series, medium beam angle for animation effects
• MFX100LWTW: 50° lens for Mosaico FX100 series, wide beam angle for animation effects
• MFX100LWGVW: 70° FLEX lens for Mosaico FX100 series, very wide beam angle, animation and
gobo
• MFX100LGBM: 30° lens for Mosaico FX100 series, medium beam angle for gobo projection
• MFX100LGBW: 50° lens for Mosaico FX100 series, wide beam angle for gobo projection
• GBVFX100120F06: Cyan lter with white stripes for MOSAICOFX100FC
• GBVFX100220F03: Red lter with white stripes for MOSAICOFX100FC
• GBVFX100320F04: Green lter with white stripes for MOSAICOFX100FC
• MFX100RAINW: Structured glass RAIN effect animation wheel
• MFX100HAMMERHEADW: Structured glass HAMMERHEAD effect animation wheel
• MFX100D35CRED: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., red
• MFX100D35CBLUE: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., blue
• MFX100D35CLGREEN: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., light green
• MFX100D35CLORANGE: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., light orange
• MFX100D35CMARINE: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., acquamarine
• MFX100D35CPINK: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., pink
• MFX100D35CYELLOW: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., yellow
• MFX100D35CMAGENTA: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., magenta
• MFX100D35CCYAN: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., cyan
• MFX100D35CGREEN: Color for MFX100CH for MOSAICOFX100FC, 34,5 mm d., green
• MFX100WE2: Standard structured glass effect wheel, long shaft 2 (included with projector)
• MFX100WE1: Standard structured glass effect wheel, short shaft 1 (included with projector)
• MFX100GW: Gobo wheel for MOSAICOFX100FC series (gobos not included)
• MFX100CW: Color wheel for MOSAICOFX100FC series
• MFX100GH: Gobo holder for MOSAICOFX100FC series (gobo not included) with manual indexing
• MFX100CH: Color holder for MOSAICOFX100FC series (color lters not included)
• MFX100SNOOTBK: Snoot for MOSAICOFX100FCBK series, black
• MFX100SNOOTGY: Snoot for MOSAICOFX100FCGY series, gray
• MFX100SNOOTPROTGY: Anti tampering full snoot with front glass, gray
• MFX100SNOOTPROTBK: Anti tampering full snoot with front glass, black

PROLIGHTS - Mosaico FX10006
• AWEXDC1221ADP: Signal adapter kit from AWEXDC1 series to AWEXDC2 series and vice versa
• AWEXAC12ADP: Power adapter from AWEXAC1 cable series to AWEXAC2 cable series
• AWEXAC1L03: IP67 power extension cable for outdoor architectural projectors, L.03 m
• AWEXAC1L05: IP67 power extension cable for outdoor architectural projectors, L.05 m
• AWEXAC1L10: IP67 power extension cable for outdoor architectural projectors, L.10 m
• AWEXAC1L20: IP67 power extension cable for outdoor architectural projectors, L.2 0m
• AWEXDC1L03: IP67 DMX extension cable for outdoor architectural projectors, L.03 m
• AWEXDC1L05: IP67 DMX extension cable for outdoor architectural projectors, L.05 m
• AWEXDC1L10: IP67 DMX extension cable for outdoor architectural projectors, L.10 m
• AWEXDC1L20: IP67 DMX extension cable for outdoor architectural projectors, L.20 m
• LRLUNA: Single Universe DMX transceiver with Bluetooth
• LLRAURORA: Single Universe DMX/RDM transceiver with WiFi and Bluetooth
• RSR1235B: Steel security cable for hanging bodies, inox steel shackle, L=120 cm, black
• C6002B: Slim aluminum clamp, 200kg loading, 48-51mm tubes, M10 bolt, Black
• UPBOX2P5: Firmware uploader kit, USB IN, 5-pin XLR DMX OUT
2 - TECHNICAL DRAWING
246 mm
[9.7 in]
273 mm
[10.8 in]
237~281 mm
[9.3~11,1 in]
Ø342 mm
[13.5 in]
195 mm
[7.7 in]
Ø48~56 mm
[1,9~2.3 in]
289~333 mm
[11.4~13,1 in]
Weight: 5,7 kg - 12,56 lbs MOSAICOFX100
Fig. 01

PROLIGHTS - Mosaico FX100 07
Fig. 02
3 - INSTALLATION
MOUNTING
Check that the supporting structure can safely bear the weight of all installed xtures, clamps, cables,
auxiliary equipment, etc. and complies with locally applicable regulations.
When suspending the xture above ground level, secure it against failure of primary attachments by
attaching a safety wire that is approved as a safety attachment for the weight of the xture to an anchor
point on the product main frame.
Do not use removable parts or weak anchors for secondary attachment.
Warning! When clamping the xture to a truss or other structure at any angle, use clamps of half-cou-
pler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
C6002A/B
clamp
RSR1235A/B
Steel security cable
98 mm
3,85 in
13 mm
0,51 in

PROLIGHTS - Mosaico FX10008
5 - START UP
CONNECT AND DISCONNECT POWER FROM THE PRODUCT
To apply and disconnect power to the product:
• Check that the product is installed and secured as indicated in the Safety Informations, and that
personal safety will not be put at risk when the xture lights up.
• Connect the power connector into the Mains input socket (100-240 VAC-50/60 Hz).
• The product is then ready for its operations and can be controlled through the available input sig-
nals on board.
• To disconnect power from the product, disconnect the Mains from the socket.
4 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the xture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a
grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts
about proper installation, consult a qualied electrician.
The max power consumption is 127W.
Core (EU) Core (US) Connection Plug terminal marking
Brown Black Live L
Blue White Neutral N
Yellow+green Green Earth

PROLIGHTS - Mosaico FX100 09
6 - PRODUCT OVERVIEW
1. BRACKET.
2. STAND ALONE CONTROL WITH 3 PUSH ENCODER.
3. GORE VALVE.
4. POWER IN: for connection to the Mains 100-240V~/50-60Hz.
5. DMX IN (3-pole): 1 = GND, 2 = sign-, 3 = sign+.
6. ANTENNA.
7. DMX OUT (3-pole): 1 = GND, 2 = sign-, 3 = sign+.
8. POWER OUT: for connection to the Mains 100-240V~/50-60Hz.
9. MAIN FUSE HOLDER: replace a burnt-out fuse by one of the same type only (T2A 250V).).
1
96 84 753
2
Fig. 03

PROLIGHTS - Mosaico FX10010
Fig. 05 - Example conguration (Output at 230 V)
MALE POWER
IP67 CONNECTOR
FEMALE POWER
IP67 CONNECTOR
N L
E
L N
E
Unit 1 Unit 2 Unit 3 Unit 8 Unit 9
POWER
IN
POWER
IN
MAINS 230V
POWER
IN
POWER
IN
POWER
IN
POWER
OUT
POWER
OUT
POWER
OUT
POWER
OUT
NOTE: when not using the Power output connectors, you must seal the cable ends with the sup-
plied caps.
Fig. 04
7 - CONNECTION TO THE MAINS SUPPLY
WARNING: For protection from electric shock, the xture must be earthed!
The product is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz
AC power source from 100-240 Volts.
If you need to install a power plug on the power cable to allow connection to power outlets, install a
grounding-type (earthed) plug, following the plug manufacturer’s instructions. If you have any doubts
about proper installation, consult a qualied electrician.
The max power consumption is 120W.
You can link up to 25 units at 230 V. Never exceed this number. Power linking cords can be purchased
separately.
When connecting the unit to a local power, it may be necessary to use the Schuko to IP67 adapters
supplied with this product.
Core (EU) Core (US) Connection Plug terminal marking
Brown Black Live L
Blue White Neutral N
Yellow+green Green Earth E
. . . . . . . . . . . .
. . . . . . . . . . . .

PROLIGHTS - Mosaico FX100 11
8 - DMX CONNECTION
CONNECTION OF THE CONTROL SIGNAL: DMX LINE
The product has connectors for DMX input and output.
The default pin-out on both connectors is as the following diagram:
Fig. 06
Pin1 : GND - Shield
Pin2 : - Signal
Pin3 : + Signal
DMX - OUTPUT
IP67 CONNECTOR
DMX - INPUT
IP67 CONNECTOR
INSTRUCTIONS FOR A RELIABLE DMX CONNECTION
Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot trans-
mit control data reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters (1000 ft).
Heavier gauge cable and/or an amplier is recommended for longer runs.
To split the data link into branches, use splitter-ampliers in the connection line.
Do not overload the link. Up to 32 devices may be connected on a serial link.
NOTE: To connect the unit to your DMX network, it is necessary to use the adapters XLR 5 pin-
IP67 signal connector, supplied with this product.
CONNECTION DAISY CHAIN OF THE DMX LINE
Connect the DMX data output from the DMX source to the product DMX input (male connector).
Run the data link from the product DMX output (female connector) connector to the DMX input of the
next xture.
Terminate the data link by connecting a 120 Ohm signal termination.
The termination is prepared by 120Ω 1/4 W resistor between pins 2 and 3 of the male DMX connector.
Install a DMX termination plug on the last xture on the link. If a splitter is used, terminate each branch
of the link.
NOTE: when not using the DMX input or DMX output connectors, you must seal the cable ends
with the supplied caps.
The following diagram shows the DMX connection:
1 2
3
2 1
3
Fig. 07 - Example 6 DMX channels conguration
. . . . . . . . . . . .
DMX Address: 33 DMX Address: 75DMX Address: 47 DMX Address: 61
. . . . . . . . . . . .
DMX512 Controller
DMX IN DMX IN DMX IN DMX INDMX OUT DMX OUT DMX OUT DMX OUT

PROLIGHTS - Mosaico FX10012
CONNECTION OF THE CONTROL SIGNAL: DMX LINE ADAPTERS
The product has XLR sockets adapters for DMX input and output.
The default pin-out on both socket is as the following diagram:
Fig. 08
Pin1 : GND - Shield
Pin2 : - Signal
Pin3 : + Signal
Pin4 : N/C
Pin5 : N/C
DMX - OUTPUT
XLR socket
DMX - INPUT
XLR plug
CONNECTION OF THE DMX LINE
DMX connection employs standard XLR connectors. Use shielded pair-twisted cables with 120Ω im-
pedance and low capacity.
CONSTRUCTION OF THE DMX TERMINATION
The termination is prepared by soldering a 120Ω 1/4 W resistor between pins 2 and 3 of the male XLR
connector, as shown in gure:
Fig. 09
Example:
5 pin XLR connector
4
DMX ADDRESSING
In order to start controlling the product via DMX, the rst step is to select a DMX address, also known as the
start channel, this is the rst channel used to receive instructions from a DMX controller. If you wish to control
the product individually, it is necessary to assign a different starting address channel to each xture.
The number of channels occupied from the product depends on the DMX mode selected, so always verify the
DMX Mode before start addressing.
If you assign two xtures the same address, they will be executing the same behaviour. Selecting the same
address to multiple xtures can be useful for diagnostic purposes and symmetrical control.
DMX addressing is limited to make it impossible to set the DMX address so high that you are left without
enough control channels for the product.
Set the xture’s DMX address by RDM with the DATAMASTER.

PROLIGHTS - Mosaico FX100 13
OPERATION AS A WIRELESS RECEIVER
MOSAICOFX100FC can be used as wireless receiver connected to a wireless transmitter.
The unit uses a DATAMASTER for conguration purposes. To use MOSAICOFX100FC as wireless re-
ceiver, have to set this function for please follow the procedure below:
• Turn on the DATAMASTER;
• Select the "RDM" function;
• Wait the discovering of all units;
• Select the desired unit and press ENTER button;
• Search for "Specic PID" item in the menu;
• Select the "Description" function;
• Scroll through the menu items until"CRMX POWER", and set value to 1;
• Select "CRMX LINK RESET" and set value to 1;
• On the transmitter, enable TX LINK to ON to link transmitter to the receivers;
• If the connection is successful and DMX input is available the display the display on the receiver unit
will shows the DMX address. If DMX signal is not available, the display will shows "No signal" but
keeps the transmitter linked;
• If the connection fails, check the position of the receiver;
• Check wireless signal in the "WIRELESS QUALITY" RDM menu item indicates the received signal
strength.
Reset the receiver
Follow the procedure below to reset the receiver.
• Turn on the DATAMASTER;
• Select the "RDM" function;
• Wait the discovering of all units;
• Select the desired unit and press ENTER button;
• Search for "Specic PID" item in the menu;
• Select the "Description" function;
• Scroll through the menu items until"CRMX LINK RESET", and set value to 1.
CRMX TO DMX (RX)
This function enable or disable the retransmission of the wireless DMX signal received throught the
DMX port on the receiver side. Follow the procedure below to activate this function:
• Turn on the DATAMASTER;
• Select the "RDM" function;
• Wait the discovering of all units;
• Select the desired unit and press ENTER button;
• Search for "Specic PID" item in the menu;
• Select the "Description" function;
• Scroll through the menu items until"CRMX TO DMX", and set value to 1.

ENCODER FUNCTION 2
(Motor 2)
ACTION Single Press Jump to next STATE ash 2 times actual color
Turn Modify value of the STATE
CURRENT STATE
Indexing Rotation CW Rotation CCW
0-360° Speed slow to fast Speed slow to fast
ENCODER DIMMER
ACTION
Long Press (3s) Highlight (FULL ON)
Single Press Jump to next STATE
Turn Modify value of the STATE from 0 to 100%
CURRENT STATE
DIMMER R G B W
Flash 3 times full on Flash 2 times full red Flash 2 times full green Flash 2 times full blue Flash 2 times full white
ENCODER FUNCTION 1
(Motor 1)
ACTION Single Press Jump to next STATE ash 2 times actual color
Turn Modify value of the STATE
CURRENT STATE
Indexing Rotation CW Rotation CCW
0-360° Speed slow to fast Speed slow to fast
PROLIGHTS - Mosaico FX10014
Fig. 10
DIMMER FUNCTION 1 FUNCTION 2
DMX IN DMX OUT
ANTENNA
MAINS OUT
MAX 0.95A
DMX512:
1=GND
2=SIGN(-)
3=SIGN(+)
4/5=NC
DISCONNECT POWER
BEFORE SERVICING
WARNING!
• SEE PROLIGHTS.IT FOR INSTALLATION
INSTRUCTIONS • BEFORE OPERATION
ENSURE THAT VOLTAGE AND FREQUENCY
MATCH LOCAL POWER SUPPLY • REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL • TA = 45°C - TCASE = 54,2°C •
DO NOT LOOK DIRECTLY INTO THE LIGHT •
RISK OF FIRE AND ELECTRICAL SHOCK
• LED ARE NOT REPLACEABLE • SUITABLE
FOR WET LOCATIONS • NOT FOR
HOUSEHOLD USE • NOT FOR RESIDENTIAL
USE • REPLACE PROTECTIVE SHIELDS
IF DAMAGED • ALWAYS SECURE FIXTURE
WITH SAFETY WIRE BEFORE SUSPENDING
ATTENTION!
• VOIR PROLIGHTS.IT POUR LES
INSTRUCTIONS D'INSTALLATION
• AVANT
LA MISE SOUS TENSION, VÉRIFIER QUE
LE VOLTAGE ET LA RÉQUENCE SONT
RÉGLÉS SUR VOTRE ALIMENTATION
LOCALE • CONFIER LA MAINTENANCE À
UN PERSONNEL QUALIFIÉ • TA = 45°C -
TCASE = 54,2°C • NE PAS REGARDER
DIRECTEMENT DANS LA SOURCE
LUMINEUSE • RISQUE DE FEU ET DE
CHOC ÉLECTRIQUE •
CONVIENT AUX
EMPLACEMENTS MOUILLES
• REMPLACER
TOUTES LES TÔLES DE PROTECTION
DÉTÉRIORÉES • TOUJOURS INSTALLER
UNE ÉLINGUE DE SÉCURITÉ
RISK GROUP 2 - CAUTION!
• POSSIBLY HAZARDOUS OPTICAL
RADIATION EMITTED FROM THIS PRODUCT
• DO NOT STARE AT OPERATING LAMP
• MAY BE HARMFUL TO THE EYE
GROUPE DE RISQUE 2 - ATTENTION!
• LE RAYONNEMENT OPTIQUE ÉMIS PAR CE
PRODUIT PEUT-ÊTRE HASARDEUX
• NE PAS REGARDER LA LAMPE DE
FONCTIONNEMENT • PEUT ÊTRE NOCIF
POUR LES YEUX
PRODUCT TESTED AGAINST EN62471
• PRODUIT TESTÉ CONTRE EN62471
MAINS IN: 100-240V
AC 50/60 Hz
MAX POWER: 127W
MAX CURRENT DRAW: 1.3A
FUSE T3.15A 250V
USE REPLACEMENT
FUSES RATED
EMPLOYER DES FUSIBLES
DE RECHANGE
COUPER L’ALIMENTATION
AVANT L’ENTRETIEN
WEIGHT: 6,2 kg
MADE IN CHINA
9 - CONTROL WITH PUSH ROTATORY KNOB
The product is equipped with rotatory knobs for manual control of the product, those are enabled only
in Stand Alone mode and they enable access to control certain attributes according to the selected
STAND ALONE mode as indicated below.
In the following image the Rotatory Knob Layout.

BUTTON CONTROL SHORTCUT
Keys Mode Description
Encoder 1 + Encoder 2
long press (3s) - Triggers WDMX Reset - Flash 2 times current color
Encoder 1 + Encoder 3
long press (10s) - Enable/ Disable Key lock - Flash 2 times current color
10 - SHORTCUT
PROLIGHTS - Mosaico FX100 15

PROLIGHTS - Mosaico FX10016
11 - RDM MENU STRUCTURE
The following chart describes the MENU tree of the product, the terms shown in BOLD indicates the
default settings.
1DMX
ADDRESS
001 - 512 Set address used for Fixture.
2DMX MODE STANDARD Set DMX chart for Main Fix-
ture.
3DIMMER
CURVE
LINEAR To choose the dimmer curve.
S-CURVE
SQUARE LAW
INVERSE SQUARE LAW
4DIMMER
SPEED
AUTO To choose the dimmer curve.
FAST
MEDUIM
SLOW
5 LED
FREQUENCY
600Hz Select PWM frequency.
1200Hz
2000Hz
4000Hz
6000Hz
25kHZ
6DMX FAULT HOLD To choose the behaviour of
xture in case of dmx signal
lost.
BLACKOUT
STAND ALONE
7INVERT
ROTATION
OFF
ON
8FAN MODE AUTO Select Fan behaviour.
HIGH
SILENT
OFF
9CALIBRATION
PIDS
RED 125 - 255
GREEN 125 - 255
BLUE 125 - 255
WARM WHITE 125 - 255
...
10 INFORMA-
TIONS
DEVICE TIME FIXTURE
HOURS
TOTAL ( ONLY READ) To check the total working
hours of the unit.
PARTIAL (READ AND RESET)
CURRENT
HOURS
TOTAL ( ONLY READ) To check the current working
hours of the unit.
PARTIAL (READ AND RESET)
SOURCE
HOURS
TOTAL ( ONLY READ) To see the total operating
hours of the LED source.
PARTIAL (READ AND RESET)
POWER ON
CYCLE
TOTAL ( ONLY READ) To see the power cycles of the
machine.
PARTIAL (READ AND RESET)
MAINTENAN-
CE TIME
ELAPSED TIME To choose and reset unit
maintenance warning hours.
ALERT PERIOD 10 -1000
POWER CONSUMPTION To see the power consump-
tion
TEMPERATURE NEAR SOUR-
CE TEMP,
DRIVER PCB
TEMP, LED
PCB TEMP,…
To see the unit temperature.
SOFTWARE VERSION View informations about soft-
ware version.
DEVICE INFO To see device info.
DEVICE LABEL To see device label.
RDM UID View ID for the RDM control.

PROLIGHTS - Mosaico FX100 17
11 STAND
ALONE
MASTER/SLAVE MASTER DMX Allow you to link and operat-
ing in synk multiple units with-
out a DMX console. Choose a
unit to perform as the Master.
This unit must be the rst unit
in line; Set the successive
units to be slave.
MASTER NO
DMX
SLAVE
STATIC STATIC
COLORS
DIMMER: 0-255
MOTOR 1 ROT
MOTOR 2 ROT
Select of the following pre-
dened color combination
and its Dimmer value. After
enabled this mode, the unit
will be automatically assigned
as Master.
WHITE
PRESETS
COLOR
MACRO
MANUAL
RGBW
12 FACTORY
DEFAULT
To reset the unit to factory de-
fault settings.
EXAMPLE
FIXED COLOR
0: R
1: G
2: B
3: W
4: GB
5: RB
6: RG
7: RGB
8: RW
9: GW
10 : BW
11 : RGW
12 : RBW
13 : GBW
14 : RGBW

RDM Model ID
0xA022
PROLIGHTS - Mosaico FX10018
12 - RDM FUNCTIONS
The product can communicate using RDM (Remote Device Management) protocol over a DMX512
Networks.
RDM is a bi-directional communications protocol for use in DMX512 control systems, it is the open
standard for DMX512 device conguration and status monitoring.
The RDM protocol allows data packets to be inserted into a DMX512 data stream without affecting
existing non-RDM equipment. It allows a console or dedicated RDM controller to send commands to
and receive messages from specic xtures.
The PIDs in the following tables are supported in the product.
RDM is also available on Wireless and Tiny's Downstead must be enabled in its custom PIDs to work.
RDM PIDs
Parameter Category PID
Address GET SET Value Description
DEVICE_INFO Product
Information 0x0060 x
PRODUCT_DETAIL_ID_LIST Product
Information 0x0070 x
DEVICE_MODEL_DESCRIPTION Product
Information 0x0080 x
MANUFACTURER_LABEL Product
Information 0x0081 x
DEVICE_LABEL Product
Information 0x0082 x x
FACTORY_DEFAULTS Product
Information 0x0090 x x
SOFTWARE_VERSION_LABEL Product
Information 0x00C0 x
BOOT_SOFTWARE_VERSION_ID Product
Information 0x00C1 x
BOOT_SOFTWARE_VERSION_LABEL Product
Information 0x00C2 x
DMX_PERSONALITY DMX512
Setup 0x00E0 x x
DMX_PERSONALITY_DESCRIPTION DMX512
Setup 0x00E1 x
DMX_START_ADDRESS DMX512
Setup 0x00F0 x x
SLOT_INFO DMX512
Setup 0x0120 x
SLOT_DESCRIPTION DMX512
Setup 0x0121 x
DEFAULT_SLOT_VALUE DMX512
Setup 0x0122 x
DMX_BLOCK_ADDRESS DMX512
Setup 0x0140 x x