Proluxe DPR2000 User manual

Operations Manual
DPR2000 - Single Pass Dough Sheeter
Model #: DPR2000









WWW.PROLUXE.COM

Version: 51719

Congratulations on your selection of
the Single Pass Dough Sheeter is a
leading manufacturer of food
preparation and cooking equipment
designed for the most demanding
commercial kitchens. Proluxe
equipment is a result of the highest
quality engineering and time-tested
design.

This manual includes installation,
operation, and maintenance
procedures for your new dough
sheeter. Please read this manual
carefully and keep it with your
machine for proper operation and
lasting service.


Electrical:
208V/50-60Hz/2800W/13.5 Amps
1 phase

Also available; specify when ordering:
●Voltage: 208
●Amps: 13.5/14.2
●Watts: 2800

Includes: 72” cord and 6-30P NEMA
approved plug.

Shipping Weight:
88lbs. (39kg)



G E T T I N G S T A R T E D

Please read carefully before attempting to
use this appliance. DO NOT touch hot
surfaces.

1. Carefully unpack and clean platen
with mild soap and wipe clean with
water.

2. Place in location where it will be used
allowing for clearances per the
dimensions.

3. Plug into proper 208V wall outlet. If
other appliances are connected to
the same circuit make sure the total
load does not exceed maximum
ampacity of the circuit.


H O W T O O P E R A T E

Guidelines for operating your new dough
roller safely:

1. Turn on the unit by pressing the
green power button.

2. Adjust the thickness of the rollers by
rotating the easy adjust arm on the
right side of the unit.

3. Pre flour the hopper to make sure the
rollers have been coated. Apply a
liberal amount of flour to your
pre-portioned dough ball.

4. Slide your dough ball through the
hopper, and catch it on the other end.
You may have to run your dough ball
through multiple times to achieve
your desired thickness.
1

H O W T O C L E A N 

Proluxe machines are relatively maintenance
free. For a long lifespan, please follow the
following care procedures.

1. Unplug the unit before cleaning.

2. Loosen the 2 housing screws on the
front panel of the machine. Then lift
up the front panel.

3. Start by removing the two springs off
of the lower scraper.

4. Detach springs at each end.

5. Remove all scapers.

6. Clean rollers, scrapers, tray, and
machine housing with mild soap and
wipe clean with a damp cloth.

7. Re-attach the scrapers and springs.

8. Lower the front panel and tighten the
two housing screws.

Service Problems
Contact our factory at [phone] (U.S.
only) or approved service agency. When
contacting the factory for information, parts
or service instructions, please provide the
serial number of the machine be provided.
This number can be found on the serial plate
located on the rear of the machine.





































2

3

4




5

Part List - Model #: DPR2000


ITEM #
DESCRIPTION
DPR2000A
DPR2000B
QTY.
1
APPLIANCE LEGS 4" STAINLESS STEEL
1101097091
1101097091
4
2
RUBBER FOOT
1101097096
1101097096
4
3
GROMMET, RUBBER 3/8 ID, 7/8" OD, 3/16 THIK
110969116
110969116
1
4
BRACKET, RELAY
1101097080
1101097080
1
5
THREADED SPACER
1101097074
1101097074
2
6
BELT GUARD
11059052
11059052
1
7
NUT COUPLING 5/16-18 X 1-1/8
1101097094
1101097094
2
8
ADJUSMENT PLATE
1101097119
1101097119
1
9
HANDLE ADJUSMENT ASSEMBLY
1101097118
1101097118
1
10
PROXIMITY SWITCH SENSOR
1101097082
1101097082
2
11
MIDDLE ROLLER SPACER
1101097105
1101097105
2
12
THUMB SCREW WITH SHOULDER
1101097086
1101097086
2
13
RELAY, TERMS 30A 250V
1101097081
1101097081
1
14
STRAIN RELIEF
MPS90014
MPS90014
1
15
TERMINAL BLOCK #1 SINGLE
6991
6991
1
16
SCREW, PAN HEAD PHILLIPS 8-32 X 5/8
SP83258
SP83258
2
17
NUT, HEX 4-40
NH440
NH440
4
18
POWER CORD
110969174
110969175
1
19
NUT, HEX 10-32
NH1032
NH1032
1
20
WASHER, SAE 5/16
WSAE516
WSAE516
8
21
NUT, HEX 1/4-20
NH1420
NH1420
5
22
WASHER, INTERNAL TOOTH LOCK #6
WLIT6
WLIT6
4
23
MOTOR BASE
110623006
110623006
1
24
WASHER 3/8 SPLIT LOCK
WL38
WL38
4
25
WASHER, SAE 3/8
WSAE38
WSAE38
4
26
START-STOP COMBINATION BUTTON, W/EXTENDED
STOP
1101097083
1101097083
1
27
GEAR MOTOR ASSEMBLY 120 VOLT US MOTOR
1101097134
1101097134
1
28
BOLT, HEX 3/8-16 X 1 STAINLESS STEEL
BH38161S
BH38161S
4
29
CONNECTOR, 1/2" MALE X 3/8" CLAMP
100455167
100455167
1
30
SCREW, PAN HEAD PHILLIPS 8-32 X 5/8
SP83258
SP83258
2
31
SCREW, PAN HEAD PHILLIPS 10-32 X 3/8
SP103238
SP103238
1
6

32
PULLEY, GUIDING IDLER ASSEMBLY
11059504
11059504
1
33
PAD, VIBRATION DAMPENING
1101745768001
1101745768001
1
34
TENSIONER BAR ASSEMBLY
1101097009
1101097009
1
35
PULLEY, IDLER TENSIONER ASSEMBLY
1101097123
1101097123
1
36
PULLER, IDLER ASSEMBLY
1101097124
1101097124
1
37
PULLEY, MOTOR
1101097125
1101097125
1
38
TOP ROLLER ASSEMBLY
1101097021
1101097021
2
39
DOUBLE SEALED BEARING
1101097026
1101097026
4
40
MIDDLE ROLLER SHAFT
1101097033
1101097033
1
41
MIDDLER ROLLER BRACKET ASSEMBLY
1101097034
1101097034
1
42
PULLEY, MIDDLER ROLLER
1101097126
1101097126
1
43
PLASTIC GUARD
1101097103
1101097103
2
44
MIDDLE FRONT SCRAPER #3 SPRING PIN
1101097064
1101097064
1
45
1/4-20 SERRATED HEX NUT
NHSF1420
NHSF1420
18
46
TOP CONCENTRIC BRACKET ASSY DPR2000
110100110
110100110
1
47
PIN, ROLL 3/16 X 1 1/4
PR316114
PR316114
2
48
UPPER ROLLER SHAFT
1101097027
1101097027
1
49
RIGHT SIDE CAM
1101097029
1101097029
1
50
LEFT SIDE CAM
1101097030
1101097030
1
51
PULLEY, ROLLER UPPER
1101097127
1101097127
1
52
BOLT, HEX 5/16 X 1-1/4 STAINLESS STEEL
BH51618114S
BH51618114S
4
53
WASHER, 5/16" SPLIT LOCK
WL516
WL516
4
54
SCREW, BUTTON HEAD 1/4-20 X 1/2 STAINLESS STEEL
SB142012S
SB142012S
17
55
WASHER, SAE #8
WSAE8
WSAE8
8
56
WASHER, INTERNAL TOOTH LOCK #8
WLIT8
WLIT8
7
57
SCREW, PAN HEAD PHILLIPS 8-32 X 3/4 STAINLESS
STEEL
SP83234S
SP83234S
1
58
NUT, HEX 8-32
NH832
NH832
10
59
SCREW, BUTTON HEAD 5/16-18 X 1/2
SB5161812
SB5161812
3
60
TOP ROLLER GAUGE DECAL
DP110109720T
DP110109720T
1
61
SIDE COVER
11059508
11059508
1
62
SPRING, EXTENSION 12" O.D. X 3.0" LONG X 1/16" THK
SE123116
SE123116
1
63
BELT, V TYPE 1/2" WIDE X 5/16" THICK X 43" LONG
BV1251643
BV1251643
1
64
SLIDING PLATE
11059509
11059509
1
65
SAFETY COVER ASSEMBLY
11059506
11059506
1
66
SCREW, SET 1/4-20 X 3/4"
SST142034
SST142034
1
7

67
NUT, ACCORN 1/4-20 NICKLE PLATE
NA1420
NA1420
2
68
LOWER FRONT SCRAPER #3 SUB ASSEMBLY
11017770517
11017770517
1
69
MIDDLE FRONT SCRAPER #3 BAR
1101097063
1101097063
1
70
ANGULAR WELD STUD FOR SCRAPER #2
1101097101
1101097101
2
71
SCRAPER, TENSION SPRING
1101097052
1101097052
4
72
TOP FRONT SCRAPER #2 SUB ASSEMBLY
11017770513
11017770513
1
73
TOP FRONT SCRAPER #2 BAR
1101097057
1101097057
1
74
WASHER, INTERNAL TOOTH LOCK #10
WLIT10
WLIT10
1
75
THREADED SPACER, DPR2000
11059503
11059503
1
76
SCREW, SET 1/4-20 X 1/2
SST142012
SST142012
1
77
SCREW, BUTTON HEAD 5/16-18 X 3/4
SB5161834
SB5161834
4
78
SCREW, SET 1/4-20 X 3/8
SST142038
SST142038
2
79
FRAME WELDING ASSEMBLY DPR2000
11059501
11059501
1
80
SCREW, ROUND HEAD 4-40 X 1/2"
SR44012
SR44012
2
81
COVER, BACK
11059507
11059507
1
A1
GEAR MOTOR KIT ASSEMBLY
1105797120
1105797120
1
A2
TOP ROLLER ASSEMBLY
11059505
11059505
1
A3
MIDDLE ROLLER ASSEMBLY
1101097130
1101097130
1
A4
MIDDLE FRONT SCRAPER #3 ASSEMBLY
11017770516
11017770516
1
A5
TOP FRONT SCRAPER #2 ASSEMBLY
11017770512
11017770512
1














8



Warranty & Return Policy


Proluxe warrants all products manufactured
by it against defects in workmanship or
materials from the date of purchase for a
period of 1 year on parts and labor. This
warranty applies to only equipment
purchased and used in the United States.

Warranty period shall begin when equipment
ships. Warranty travel will only be covered
for 60 miles.

ALL WARRANTY SERVICE CALLS MUST BE
APPROVED BY PROLUXE. IF THIS
PROCEDURE IS NOT FOLLOWED,
WARRANTY SERVICE WILL NOT BE
COVERED. WARRANTY SERVICE WILL BE
PAID ON STRAIGHT TIME, OVERTIME
WILL NOT BE COVERED.

Service Calls
Contact our factory to obtain warranty
service. Proluxe must issue a return
authorization number, and call tag, or find
the name and location of a Factory
Authorized Service Center nearest you.
When calling for service, please furnish the
model number, serial number, and a
description of the problem.


E X C L U S I O N S

The warranties provided by Proluxe DO
NOT apply to the following:

●Damage due to misuse, abuse,
alteration, or accident.
●Improper or unauthorized repairs.
●Submerged in water.
●Damaged in shipment.
●Equipment exported to foreign
countries.

Special Order Equipment and
Accessories
Cannot be canceled and are not returnable
unless defective within the terms of this
warranty.
In no event shall Proluxe be liable for
consequential damages arising out of the
failure of any of its products if operated
improperly or caused by normal wear or
damaged by operator abuse.

Limited Lifetime Warranty on
Heating Elements
If replacement is needed, Proluxe will send
the new part at no charge but labor will not
be covered unless the unit is still under the 1
year manufacturer warranty.


R E T U R N E D M E R C H A N D I S E
P O L I C Y

Should it become necessary to return any of
the company’s products, the following
instructions must be adhered to: First,
contact our customer service department for
approval and a return authorization number.
9

Please have the serial number of your item
available at that time. All merchandise must
be shipped freight prepaid by customer or
service agency. Subject to the inspection of
the product by the company, a restocking
charge of 20% of the Net purchased price
paid to Proluxe will be assessed.
Merchandise may not be returned for credit
without prior written approval of Proluxe.

Collect shipments will not be accepted. No
returns after 60 days of original shipment
date on machines. Purchased parts may not
be returned after 30 days. If upon inspection
by Proluxe or its authorized agent it is
determined the equipment has not been used
in an appropriate manner, has been modified,
or has not been properly maintained, or has
been subject to misuse, misapplication,
neglect, abuse, accident, unauthorized
modification, damage during transit, delivery,
fire, flood, act or war, riot or act of God, then
this warranty shall be deemed null and void.


T E R M S & C O N D I T I O N S

1. Price List prices are suggested retail prices
and are shown in U.S. Dollars.

2. Terms of Payment: 1% 10 days, NET 30
days.

3. New Accounts: Satisfactory credit
information must be provided before open
account status can be extended.

Unless agreed otherwise, all shipments will
be made C.O.D., Cash in advance.

4. Pricing: Prices, specifications, model
numbers, capacities and accessories are
subject to change without notice.

5. Freight/Routing: Method of shipment will
be determined by Proluxe unless otherwise
advised by purchaser.

6. Damaged Claims: All merchandise shipped
at purchaser’s risk. Inspection must be made
by purchaser at time goods are received. If
goods are damaged, the PURCHASER shall
request that the agent of the transportation
company make a written notation on the
proper shipping documents immediately and
then file a claim for damages.

Note  : Goods damaged in shipping are
non-returnable.

7. Returns: Machines may not be returned
after 60 days. Purchased parts may not be
returned after 30 days. A restocking fee of
20% will be assessed on non-warranty
returns.

8. Taxes: Prices indicated herein DO NOT
include State, Federal, Local or foreign taxes
or duties, nor do they include fees, permits,
insurance or other levies, all of which are the
responsibility of the purchaser.

9. All orders are subject to acceptance by
Proluxe.

10. Possession of this price list shall not be
considered an offer to sell



10