Promate proLink.OT User manual

User Guide
proLink.OTG
OTG Hub and Card Reader

proLink.OTG is a mulfunconal accessory compable with Micro- USB port
devices. It has 3 USB ports, MSD and SD card slots. Its’ plug and play opon allows
you to use all the funconalies at the same me. Plug a mouse or a keyboard to
browse your informaon from a Card or connect with USB ports’ devices. Enjoy full
access, transfer between storage devices, without any addional cables or plugs.
Simply connect proLink.OTG to a smart phone or a tablet compable Android, you
will have instant access to all your files and cards.
1. Supported Memory Cards :
A. SD / SDHC / SDXC / EXTREME SD / EXTREME II SD / EXTREME III SD
/ULTRA SD / ULTRA II SD / ULTRA II SD PLUS / SD-ULTRA-X
/ULTRA SPEED SD / SD PRO / SD ELITE PRO / HS SD / MMC / MMC 4.0;
B. Micro SD(T-Flash) / micro SDHC / micro SDXC
2. Fully compliant with high-speed USB 2.0 transfer protocol, the maximum
transfer speed up to 480Mb/s
3. Operang temperature:0 to +60℃
4. Store temperature:-20 to + 60℃
5. Operang humidity: 20-80%
6. Store humidity: 10-95%
7. Operang system Android 2.3 or above OS
• Connecons: SD, Micro SD, 3 USB ports
• Supports OTG funcon
• Supports the latest SD v3.0 UHS-I 104 Specificaons Memory Card
• Interface: micro USB2.0(male)
• Fully compliant with high-speed USB 2.0 transfer protocol, Plug-and-play, no need
for external power supply
• Read connecon with USB ports’ devices and SD or MSD cards at the same me
Introduction
Specification
Features

• Fully compliant with high-speed USB 2.0 transfer protocol, Plug-and-play, no need
proLink.OTG
User Guide
Warranty Card
Inserng SD/micro SD cards into the corresponding slots of the proLink.OTG
direcon picture
Packing Contents
Plug in proLink.OTG to your smartphone or tablet compable OTG funcon
1. The green LED flashes about 2 seconds then goes out while the proLink.OTG is
powered on. It will keep blinking during reading and wring data process, but it
will not light while connecon with USB2.0 devices to its corresponding ports.
Operation Instructions
micro SD
Micro-SD Card
SD Card
LED Indicator

2. Indicator appear on screen of the smartphone or tablet compable OTG
while inserng USB2.0 devices or SD/micro SD cards into the corresponding
posions
3. You can freely transfer data between the SD or micro SD and connect to
USB devices
4. The USB ports and SD or micro SD card slots can be used simultaneously
Note:
5. Before removing the proLink.OTG, perform the necessary operaons to
ensure it is safe to remove the devices. Refer to the operang instrucons of
your operang system.
1. NTFC format for the device is not supported
2. The SD and micro SD slots can’t be used at the same me
Micro-SD Card
SD Card
USB Ports
Card Slots

Product Safety and usage Warnings
Please do not aempt to disassemble this product, it is possible to result in
short-circuit or even damage.
The product should be kept in dry and venlated environment, please avoid
high humidity and high temperature.
Do not install the equipment near heat sources such as fire, power, or other
goods that can product heat.
Please do not use organic solvent to clean product surface.
Please keep the product away from lile children.
Please do not drop, knock or shake the proLink.OTG
Rough handling can break internal circuit boards and mechanics.
Keep the surface clean.