Propel RC Navigator User manual
WARNING: Never leave product charging unattended for extended periods of
time. Always disconnect STUNT DRONE from charger immediately after the
STUNT DRONE is fully charged. Please refer to enclosed safety instructions.
INSTRUCTION BOOKLET
Colors and styles may vary slightly.
V 1.0 US
PACKAGE CONTAINS:
2.4G Wireless Controller Instruction BookletSpare Parts
FCC Part 15 C Notice
CAUTION:Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against
harmful interference in a residential installation.This equipment generates,uses and can radiate radio
frequency energy and,if not installed and used in accordance with the instructions,may cause harmful
interference to radio communications.However,there is no guarantee that interference will not occur in a
particular installation.If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,the user is encouraged to try to correct
the interference by one or more of the following measures:
connected.
This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions :
(1) This device may not cause harmful interference,and
(2) this device must accept any interference received,including interference that may cause undesired
operation.
14
CHOKING HAZARD
-
Small parts.
Not suitable for children under 3 years.
WARNING!
This product is manufactured by AMAX Group
12645 Memorial Drive Suite F1 #388 Houston, TX 77024
Propel™ and Propel RC™ are the licensed trademarks of Rooftop Group LTD Singapore.
©2018 All rights reserved. Visit us at www.propelrc.com
NAVIGATOR™ is the property of Eastern Design Group, USA.
©2017 All rights reserved.
Made in China
Conforms to safety requirements of FCC.
HIGH PERFORMANCE STUNT DRONE
A
B
B
A
HIGH PERFORMANCE STUNT DRONE
instruction booklet as it contains valuable information on how to properly fly and care your Stunt Drone.
FEATURES
REMOTE CONTROL BATTERY INSTALLATION
1.Unscrew and remove the battery cover from the back of the controller.
2.Install 2“AAA”alkaline batteries into the controller as shown in diagram A
4.Turn over the controller and push the power button,you will see the
indicator light turn on and start flashing.
TABLE OF CONTENTS
Features............................................................................................................2
Remote Battery Installation.......................................................................................2
Charging The Stunt Drone...........................................................................................2
Stunt Drone Diagram, Remote Diagram.........................................Syncing Your Stunt Drone...........................................................................................4
Preparing For Flight..................................................................................................4
Flying Tips............................................................................................................4
Recognizing the Front and Rear of the ..............................................................5
............................................................................................ 5
........................................................................................... 5
........................................................................................Speed Setting Button ..................................................................T (Training)MODE ......................................................................4 Channel Flight Control ........................................................................................... 7
........................................................................................... 8
Calibrating The Stunt Drone ........................................................................................ 9
..................................................................................................... 9
Replacing The Propeller Blade....................................................................................11
Battery Warnings, Care and Maintenance......................................................................12
.................................FCC Part 15 C Notice................................................................................................14
1 2
C
A.
Battery Compartment
(2“AAA”batteries not included)
CHARGING THE STUNT DRONE
1. Make sure the Stunt Drone’s power switch is in the“OFF”position and plug the USB charging cord into the
charging socket of the Stunt Drone(see diagram B ).
Caution:The USB plug fits the charging socket only in one way.Do not force it.
2.
Connect the USB end of the charging cable to your computers USB port or a USB wall charger (see diagram C).
Note these charging times are based on 5.0V system with 2.0A or higher USB outlet.
Note:If the red LED lights up,either the charging is complete or the USB plug is not properly connected.
4. The charging time will vary depending on the percentage of battery already charged.The average charging time is
The Low battery indication:the Stunt Drone‘s LED lights will begin to flash to notify you that the battery is running
low.The lights will continue to flash before the Stunt Drone automatically lands.
B
D
plug lights up when
charging is complete
STUNT DRONE DIAGRAM
REMOTE DIAGRAM
FLYING TIPS
200 foot radius.
Wind can greatly affect the performance of the Stunt Drone.
Important! When syncing your Stunt Drone quadrocopter with the controller always make sure
that the quadrocopter is on a flat level surface and that your digital trim settings are in the center
position.This ensures that the 6 Axis gyro is properly programmed to mimic your trim settings.
Your Stunt Drone utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side
by side in the same wireless range with no interference.
For One Person Play:
1.Before starting,make sure that your controller is OFF and the Stunt Drone’s battery is disconnected.
Make sure that there are no other 2.4G devices in the area as well.
2.Turn ON the Stunt DroneStunt Drone
should begin to flash rapidly.
throttle stick all the way up until it stops and then pull it back all the way down to the bottom.When
indicating lights on the drone and controller will stop flashing and stay solid on.Your Stunt Drone and
remote should have successfully synced.Should this not happen,repeat all steps again.
For Multi Person Play:
4.Before starting,make sure that the power on all Stunt Drone’s and Controllers are OFF. Make sure that
there are no other 2.4G devices in the area as well.
5.Each person will have to sync his Stunt Drone individually at a different time to avoid interference.
After syncing a player’s Stunt Drone,it should be left ON until all players have synced their quadrocopters.
SYNCING YOUR Stunt Drone
DO NOT ATTEMPT TO FLY YOUR Stunt Drone IF THERE IS RAIN,SNOW,HEAVY WINDS,THUNDER OR LIGHTNING
OUTDOORS.IT COULD DAMAGEYOUR PRODUCT AND POSSIBLY EVEN CAUSE BODILY HARM.
PREPARING FOR FLIGHT
3 4
DO NOT FLY YOUR DRONE IN FOUL WEATHER!
WARNING
Direction Control
Right Trim
Backward Trim
Forward Trim
Speed Setting Power Switch
Power Indicator
Safety Guard
Rotor Blade Charging
Socket
The safety guard is easy to clip on and off.Simply pull the clips away
from each motor mount and remove the Stunt Drone from below.
OFF ON
Stunt Roll
NOTE: The use of the Trim buttons are accompanied with a Beep tone.A single long Beep indicates the
product is center trimmed.No beeps after press indicates the product is trimmed to the maximum on a
particular side.
UNDERSTANDING TRIM ADJUSTMENTS
Forward/Backward Trim
driftsthe moving stops and proper flight is maintained.
drifts backwards,push and release the FORWARD TRIM (F)button in the same
manner until the problem is resolved.
Banking Left/Right Trim
the banking stops and proper flight is maintained.
manner until the problem is resolved.
SPEED SETTING BUTTON
The Stunt Drone has 4 speed settings;T(Training),1(SLOW),2(MEDIUM) and 3(HIGH).The Default
setting when you first turn on your Stunt Drone is 1(SLOW).To change speed,just press and release the
sounds,one beeping sound for slow speed,two for medium speed and three for high speed.
AUTOMATICALLY TAKE OFF / LAND
Make sure you have properly synced The Stunt Drone .
take off.
will descend and land automatically.
Tips:You also can move the two control sticks simultaneously down to the inside or outside corners,hold
them till the blades start spinning.Release the control sticks and push the throttle stick slowly to take off
manually.
UNDERSTANDING THE ALTITUDE LOCK SENSOR
The control and
stability.It allows the user to ease into piloting the drone.The sensor locks in the altitude of the
drone while allowing the user to adjust the directional controls without having to hold the throttle.
After starting the drone,fly it upwards to a safe height.Once at a safe height,release the throttle to the
neutral position.Now your Stunt Drone should be locked in the altitude and you can focus on getting
used to the directional controls of the Stunt Drone.The drone always will tends to self correct and go
back to the last locked height after moved up or down by outside forces.
Note:The altitude sensor does have some tolerance based on atmospheric conditions and could have a
slight variation in altitude.
Forward/Backward
Trim Controls
Push and release
to go backward
If flying forward... If flying backward...
Push and release
to go forward
Left/Right Banking Controls Push the left button to
increase left banking
sensitivity
Push to right button to
increase right banking
sensitivity
5 6
Front
F
Forward/ Backward
Trim
Bank
Bank
RECOGNIZING THE FRONT AND REAR OF THE QUADROCOPTER
"forward" facing direction and "rear" or backwards facing direction.
side with two gray blades (see diagram F ).The rear or”backward”
and the two black propellers (see diagram F).
NOTE:The front of the Quadrocopter displaysWHITE LED lights and the
back of the Quadrocopter displays RED LED lights.
T (Training)MODE
Simply press and hold the Speed Setting Button;till you heared a long beep,now you are inT Mode.T
mode allows you to learn how to operate your Stunt Drone at a very slow speed.Also in T mode a
minumum and maximum height limit are set to help avoid crashing into the ground or ceiling while
learning. To exit T mode just short press the speed setting button again.
3/4 CHANNEL SELECT
Stunt Dronechannel mode (beginner) or 4 channel mode (advanced flying).
The Stunt Drone default setting is 4 channel mode.
PRESS the Direction Control stick vertically down then release,
Stunt Drone now is
Rear
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
4 CHANNEL FLIGHT CONTROL
fly your Stunt Drone it is best to start with a large space until you get used to the basic controls.As you
master flying your Stunt Drone you can move to more advanced maneuvering techniques.Practice makes
Move the leftThrottle stick up to increase the
speed and the Stunt Drone will accelerate and
ascend.
Move the leftThrottle stick down to decrease the
speed and the Stunt Drone will decelerate and
descend.
Move the leftThrottle stick left and the Stunt
Move the leftThrottle stick right and the Stunt
Move the right Direction Stick up and the Stunt
Drone will move forward.
Move the right Direction Control down and the
Stunt Drone will move backward.
3 CHANNEL FLIGHT CONTROL
fly your Stunt Drone it is best to start with a large space until you get used to the basic controls.As you
master flying your Stunt Drone you can move to more advanced maneuvering techniques.Practice makes
Move the right Direction Control left and the
Stunt Drone will bank to the left.
Move the right Direction Control right and the
Stunt Drone will bank to the right.
7 8
speed and the Stunt Drone will accelerate. the speed and the Stunt Drone will descend.
Move the right directional stick RIGHT to
Move the Right Direction Stick forwards and
the Stunt Drone will move forward.
Move the Right Direction Stick backwards down
and the Stunt Drone will move backwards.
To change back to 4 Channel mode:
PRESS the Direction Control stick vertically down then release again,you will hear 4 short beeps
indicating the Stunt Drone is now set to 4CH mode.
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
A
A
B
A
A
A
B
B
B
B
B
A
A
A
A
A
A
A
A
A
A
B
A
A
B
B
B
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
A
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
A
B
B
A
J
9 10
FRONT
REPLACING THE PROPELLER BLADE
Gray Blade Front Left = A
Gray Blade Front Right = B
Black Blade Back Left = B
Black Blade Back Right = A
Your Stunt Drone propeller system is a precision instrument that may need repair or replacement from
to your Stunt Drone propellers.
1.The Stunt Drone has four blades,two gray color ones on front,and two black color ones on back (see
2.When replacing the propeller blades,make sure to match both the color and indication letter on the
HOW TO DO 360º STUNT ROLLS
1.In order to make your Note:The Stunt Drone means you are now in“STUNT MODE."
Stunt Drone
will instantly roll in the associated direction.See diagram below.
Note:
REAR
1.Place the
Stunt Drone
on a flat level surface.
2.Make sure the
Stunt Drone
is on and that the controller is synced
(refer to syncing pg 4).Do not start the blades.Instead move both the
throttles and control stick down and to the right corner (see diagram
E).You will hear a beep and see the lights on the drone rapidly flash
and stop.Once the lights stop flashing you have completed your
TROUBLE SHOOTING:
If you do not see the lights flash,first turn off
the switch from the drone then turn off your controller and start
again.Always make sure to turn on the switch in first,then turn on your controller.Push the left throttle stick up
all the way and then pull back down again.When you hear the beep the Stunt Drone is synced to the controller
and you are ready to calibrate.
CALIBRATING THE STUNT DRONE
E
A
B
B
A
11 12
STUNT DRONE WARNING
:
The Stunt Drone is designed for INDOOR or OUTDOOR. The Stunt Drone blades revolve at high speeds and
can cause damage to the user,spectators and animals.Stand away from the Stunt Drone to reduce the risk
of getting into the flight path.Warn spectators that you will be flying your Stunt Drone so that they are
aware of its position.Before flight,inspect the rotor blades to make certain that the blades are securely
fastened to the Stunt Drone.
WARNING!
any other battery.
BATTERY WARNINGS
RECHARGEABLE BATTERY:
battery properly according to local disposal requirements.
CONTROLLER BATTERIES:
Remote control requires 2“AAA”batteries (not included).Please read the important battery safety warning below.
according to state or local government ordinances and regulations.
CARE AND MAINTENANCE
extended period of time.
Limited 90-Day Warranty NORTH AMERICA
AMAX Group USA warrants to the original consumer that this product is free from any
electrical or mechanical defects for a period of 90 DAYS from the date of purchase.If any such
defect is discovered within the warranty period, AMAX Group USA will repair or replace the
unit free of charge upon receipt of the unit,shipped postage prepaid and insured to our
warranty center. The warranty covers normal consumer use and does not cover damage that
occurs in shipment or failure that results from alterations, accident, misuse,abuse, neglect,
wear and tear, inadequate maintenance,commercial use or unreasonable use of the unit.
Removal of any parts/components voids all warranties.This warranty does not cover cost of
repairs made or attempted outside by third-party individuals or companies. Any applicable
implied warranties, including warranties of merchantability and fitness, are hereby limited to
90 DAYS from the date of purchase.Consequential or incidental damages resulting from a
breach of any applicable express or implied warranties are hereby excluded. Some states do
not allow limitations on the duration of implied warranties and do not allow exclusion of
incidental or consequential damages,so the above limitations and exclusions in these
instances may not apply.
REPAIR/REPLACE PRODUCT
If your product begins to malfunction or stop working, immediately email our warranty
center at the email listed below. If it is determined that a return is necessary, our warranty
department will issue you an RMA number/form and an address to the nearest return center
for shipping the product to.IMPORTANT NOTICE:We will reject all returns that are not
accompanied by an issued RMA form and number so make sure to contact our warranty
center before attempting to return your product!
PREPARATION FOR SHIPPING YOUR PRODUCT
Please repack your product in a durable box,preferably in the original carton, and send it
prepaid,and adequately insured. Include the RMA form that was issued by our warranty
department along with your daytime telephone number and email address inside the
shipping carton. If your warranty has expired,contact our warranty center for charged service.
IMPORTANT NOTICE! DO NOT ATTEMPT TO SHIP
YOUR PRODUCT BACK WITHOUT FIRST CONTACTING
OUR WARRANTY DEPARTMENT BY EMAIL AT:
customercare@amaxbrands.com
Table of contents
Other Propel RC Drone manuals
Propel RC
Propel RC TILT User manual
Propel RC
Propel RC BATWING User manual
Propel RC
Propel RC DART 1.0 User manual
Propel RC
Propel RC SPYDER X User manual
Propel RC
Propel RC PROTON-Z User manual
Propel RC
Propel RC cloud force User manual
Propel RC
Propel RC SNAP 2.0 User manual
Propel RC
Propel RC ATOM X User manual
Propel RC
Propel RC HD SONIC DRONE User manual
Propel RC
Propel RC FLEX 2.0 User manual
