Prorack K417 User manual

K417
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 2 x 4
Revision No: 5E 1

Fitting Kit K417
MAX kgs (lbs)
W/P WHD
Fiat
Punto, 5dr Hatch 99-03 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto, 5dr Hatch 99-03 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto, 5dr Hatch 99-03 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Punto, 5dr Hatch 99-03 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2

Fitting Kit K417
X
A B C 1 2 3
Punto, 5dr Hatch 99-03 (AU) -280mm 520mm - 775mm 760mm -
-11" 20 1/2ths" - 30 1/2ths" 29 15/16ths" -
Punto, 5dr Hatch 99-03 (EU) -280mm 520mm - 775mm 760mm -
-11" 20 1/2ths" - 30 1/2ths" 29 15/16ths" -
Punto, 5dr Hatch 99-03 (ZA) -280mm 520mm - 775mm 760mm -
-11" 20 1/2ths" - 30 1/2ths" 29 15/16ths" -
Punto, 5dr Hatch 99-03 (NZ) -280mm 520mm - 775mm 760mm -
-11" 20 1/2ths" - 30 1/2ths" 29 15/16ths" -
3

Fitting Kit EN
K417
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K417
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K417
●Remove locking screw.
●Cut grey protective strip in two equal
lengths.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6

Fitting Kit EN
K417
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
7

Fitting Kit EN
K417
Fitment
●Pull back rubber seal to expose fixed points
on vehicle body.
●Locate vehicle's fixed points.
●Attaches to factory-fitted mounting points
located between rubber seals on door
frame
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
8

Fitting Kit EN
K417
●Insert clamp into the mounting point.
●When viewed from the top, clamp should
be lined up with the two lugs on both sides.
●Repeat for all four positions.
9

Fitting Kit EN
K417
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
10