Prorack S16 User manual

K306
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 4
Revision No: 5E 1

Fitting Kit K306
MAX kgs (lbs)
W/P WHD
Nissan
Murano Mk1, 5dr SUV 03-08 EU 75 kgs (165 lbs) 75 kgs (165 lbs)
Murano ST, 5dr SUV Aug 05-09 NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
Murano ST, 5dr SUV Aug 05-09 AU 75 kgs (165 lbs) 75 kgs (165 lbs)
Murano, 5dr SUV 03-07 US 75 kgs (165 lbs) 75 kgs (165 lbs)
2

Fitting Kit K306
X
A B C 1 2 3
Murano Mk1, 5dr SUV 03-08 (EU) -200mm 600mm - 895mm 870mm -
-7 -7/8ths" 23 5/8ths" - 35 1/4ths" 34 1/4ths" -
Murano ST, 5dr SUV Aug 05-09 (NZ) -200mm 600mm - 895mm 870mm -
-7 -7/8ths" 23 5/8ths" - 35 1/4ths" 34 1/4ths" -
Murano ST, 5dr SUV Aug 05-09 (AU) -200mm 600mm - 895mm 870mm -
-7 -7/8ths" 23 5/8ths" - 35 1/4ths" 34 1/4ths" -
Murano, 5dr SUV 03-07 (US) -200mm 600mm - 895mm 870mm -
-7 -7/8ths" 23 5/8ths" - 35 1/4ths" 34 1/4ths" -
3

Fitting Kit EN
K306
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K306
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K306
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6

Fitting Kit EN
K306
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pads (supplied with fitting kit) to
foot.
●Make sure the pad fits into the holes
underneath the foot.
7

Fitting Kit EN
K306
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
8

Fitting Kit EN
K306
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9

Fitting Kit EN
K306
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10