Proshade 2127286 User manual

R
Umbrella Base with Wheels
ITM. / ART. 2127286
ASSEMBLY INSTRUCTIONS
READ CAREFULLY
IMPORTANT, RETAIN FOR FUTURE REFERENCE:
For assistance with assembly, parts, or problem resolution please contact customer
service in US and Canada at 1-877-730-1583, 9:00AM - 5:00PM EST, Monday - Friday,
English, French, and Spanish spoken or visit proshade.com.
THIS ITEM IS INTENDED FOR OUTDOOR DOMESTIC USE ONLY,
NOT FOR COMMERCIAL USE
1
CARE INSTRUCTION:
Clean gently with environmentally - friendly soap solution and water
using a sponge. Do not use abrasive materials, wire brushes,
chemicals, cleansers or bleach. Do not use a pressure washer.
Rinse well. Allow to air dry.
SAFETY INSTRUCTIONS:
1. Do not use the umbrella base with wheels before filling it with weight.
2. The heavier the umbrella base, the more stable it will be.
3. Do not use in windy conditions. Never tilt your umbrella in windy
conditions. Always close and remove the umbrella from the base in
windy conditions.
4. Use the umbrella base with wheels on flat surfaces only. The locking
wheels are meant to keep the umbrella base with wheels locked in place
on flat surfaces. The locking wheels are not meant for locking the
umbrella base with wheels in place on sloped surfaces.
5. Keep the wheels locked except when moving your umbrella base with wheels.
The locking wheels may wear down over time making the brake
mechanism less effective. Check for wear and replace the locking
wheels when necessary.
6. Do not move, lock, or unlock the umbrella base with wheels with bare feet.
7. The umbrella base with wheels is not designed to roll in sand or grass ground.
Submerging the wheels in sand or grass will clog the ball bearings.
8. Do not allow children to play with or operate the umbrella base with wheels.
CAUTION:
Before assembling the umbrella base, read this manual and follow
the safety instructions.

2 3
NOTE: Parts shown on parts list are not to scale.
Reducer A
Reducer B
Locking device
and Reducers
Stem
Base Cover
Base
Substructure
Locking Wheels Non-Locking
Wheels
A
NO PARTS LIST DESCRIPTION QTY
1
Base Cover
1
Base
Substructure
B
1
Stem
C
1
Locking device
and Reducers
D
2
Non-Locking
Wheels
E
2
Locking Wheels
F
16
Screws
G
16
WashersH
1
Paper coverI
ASSEMBLING THE BASEParts list
Step1 - Fasten Wheels to Base Substructure.
Note: Use screws with washers to secure four wheels. Tighten screws
firmly but do not over-tighten.
Over-tightening may strip the holes.
Please note the slots for locking wheels and non-locking wheels are
different. Make sure wheels fixed at right slots.
Step 2 - Fill the Base with Bricks and Sand.
Cover the center hole with the paper cover to prevent sand from entering this area.
Place 12 bricks (see Brick Specifications) in the Base Substructure in the pattern shown.
Fill sand all around and between the bricks. Fill sand up to the height of the edge of the
Base Substructure.
Note: Sand-only can not reach the total weight 125lbs, we recommended using
bricks and sand to reach weight 125lbs. Rocks can also be used as long as the
total weight could reach 125lbs.
Remove paper cover from the center hole.
Brick Specification:
Standard size:
8 x 3 5/8 x 2 1/4 in
Weight: approx. 4 1/2 lbs
Paper cover
E
F
Screws and Washers
slot
Before assembly, have 12 bricks (recommended size 8 x 3 5/8 x 2 1/4 in ) and
50 lbs of sand ready.

45
Step 5 - Select Reducer.
The unit comes with a Reducer that fits a 1.38 inch, 1.5 inch or 1.9 inch diameter
umbrella pole.
After choosing the correct reducer then insert umbrella pole in stem, turn the handle
of locking device clockwise to secure the umbrella. The handle is equipped with a
button on the end.
Push the button and pull the handle out at the same time and you can rotate the
handle to align with the stem without loosening the stem from the pole.
MOVE WITH CAUTION:
• Base is suitable for 3.36M / 11ft Market Umbrella, or other umbrellas under
18kgs / 39.68 lbs
• Make sure umbrella is in closed position and free of objects before moving base.
Step 3 - Install the base cover.
1. To lock – press down the pedal on the locking wheels.
2. To unlock - Lift up the pedal on the locking wheels.
Locking device
Reducer B
Reducer A
LOCKING WHEELS INSTRUCTIONS
Step 4 - Install the Stem.
Insert the Stem into the Base Cover and
twist.
Push

Distributed by:
Costco Wholesale Corporation
P.O. Box 34535
Seattle, WA 98124-1535
USA
1-800-774-2678
www.costco.com
Costco Wholesale Australia Pty Ltd
17-21 Parramatta Road
Lidcombe NSW 2141
Australia
www.costco.com.au
Costco France
1 avenue de Bréhat
91140 Villebon-sur-Yvette
France
01 80 45 01 10
www.costco.fr
Costco Wholesale Japan Ltd.
3-1-4 Ikegami-Shincho
Kawasaki-ku, Kawasaki-shi,
Kanagawa 210-0832 Japan
0570-200-800
www.costco.co.jp
Costco Wholesale Korea, Ltd.
40, Iljik-ro
Gwangmyeong-si
Gyeonggi-do, 14347, Korea
1899-9900
www.costco.co.kr
Costco Wholesale New Zealand Limited
2 Gunton Drive
Westgate
Auckland 0814
New Zealand
Costco (China) Investment Co., Ltd.
Room 1003, Block 2, 2388 Xiupu Road,
Pudong New Area, Shanghai
China 201315
[phone]
Costco Wholesale UK Ltd /
Costco Online UK Ltd
Hartspring Lane
Watford, Herts
WD25 8JS
United Kingdom
01923 213113
www.costco.co.uk
Costco Wholesale Spain S.L.U.
Polígono Empresarial Los Gavilanes
C/ Agustín de Betancourt, 17
28906 Getafe (Madrid) España
NIF: B86509460
900 111 155
www.costco.es
Costco Wholesale Iceland ehf.
Kauptún 3-7, 210 Gardabaer
Iceland
www.costco.is
Costco Wholesale Sweden AB
Saluvägen 5
187 66 Täby
Sweden
Costco Wholesale Canada Ltd.*
415 W. Hunt Club Road
Ottawa, Ontario
K2E 1C5, Canada
1-800-463-3783
www.costco.ca
* faisant affaire au Québec sous
le nom les Entrepôts Costco
Importado por:
Importadora Primex S.A. de C.V.
Blvd. Magnocentro No. 4
San Fernando La Herradura
Huixquilucan, Estado de México
C.P. 52765
RFC: IPR-930907-S70
(55)-5246-5500
www.costco.com.mx
6 7
Umbrella Base with Wheels
ITM. / ART.
2127286
LETTER OF WARRANTY
Please be advised that the manufacturer provides a two-year warranty that the
umbrella base with wheels will be free from defects in original materials
and workmanship.
Frame
Frames are warranted to be free from defects in materials and workmanship for
a period of two years. Damage to frames or welds due to improper assembly or
exposure to water and sub-freezing temperatures is not covered. Do not allow
water to accumulate inside frames.
Finish
The finish is warranted against peeling, cracking, or blistering for a period of two
years, provided the unit has not been scratched or abraded. Scratches and chips
resulting from abnormal wear and tear are not covered.
AUSTRALIA: Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and for compensation for any other reasonably foreseeable loss
or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major
failure.
Note: All operation should be according to the instruction manual.
* This warranty DOES NOT COVER the following items:
Failure caused by unreasonable or abusive use; failure caused by neglect of
reasonable and necessary care; acts of nature (including but not limited to wind,
hurricanes, tornadoes, and storms) are not covered by this warranty.
The product is not covered by this warranty after two years from the date
of purchase.