ProStart CT-3471 TW User manual

Doc#: 110602 Rev: 1.3 © 2011 - CT-3471TW - -FcN- Canada
TWO-WAY 6-BUTTON LCD AUTOMATIC/MANUAL TRANSMISSION
REMOTE STARTER
CT-3471 TW
User Guide
WARNING
!
It is the responsibility of the vehicle operator to ensure their vehicle is parked
in a safe and responsible manner.
1. a) Manual transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in the NEUTRAL position and
the parking brake is engaged in order to avoid accidents upon remote starting.
b) Automatic transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in “Park” in order to avoid
accidents upon remote starting.
(Note: Make sure that the automatic vehicle cannot start in "Drive".)
2. It is the user's responsibility to ensure that the remote starter is disabled or put
into valet mode before servicing.
A note concerning the battery inside the transmitter:
Depending on your usage of the transmitter, the battery can last anywhere between 3 to 6 months. When the
battery is low, the transmitter will produce two beeps in a repetitive cycle. At that point you should replace
your battery with a new one. That is why we recommend that you keep a spare battery somewhere handy
such as the glove compartment.
INDUSTRY CANADA USER NOTICE:
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of
the device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (EIRP) is not more than that required for successful
communication.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modifications to this equipment. Such modifications could void the user's authority to operate the
equipment.

P.2 User Guide
TABLE OF CONTENT
INTRODUCTION .......................................................................................................................3
WHAT IS “ESH”TECHNOLOGY?........................................................................................................3
VEHICLE PRESETS..........................................................................................................................3
HEATER..........................................................................................................................................3
WINDSHIELD WIPERS &RADIO &HEADLIGHTS...................................................................................3
USING THE REMOTE CONTROL.....................................................................................................3
LCDREMOTE FUNCTIONS................................................................................................................3
BASIC VEHICLE OPERATIONS............................................................................................................4
TRANSMITTER MODE SELECTION ......................................................................................................5
HOW TO ACCESS REMOTE’S FUNCTION MENUS:...................................................................................5
TIMER COUNTDOWN ADJUSTMENT....................................................................................................5
ARMING AND DISARMING THE STARTER KILL...........................................................................6
REMOTE-STARTING YOUR VEHICLE.............................................................................................7
SETTING YOUR VEHICLE INTO READY MODE......................................................................................7
REMOTE-STARTING..........................................................................................................................8
DRIVING OFF...................................................................................................................................8
REMOTE STARTER FEATURES......................................................................................................8
REMOTE DOOR LOCKS.....................................................................................................................8
REMOTE TRUNK RELEASE................................................................................................................8
IDLE MODE......................................................................................................................................8
VALET MODES.................................................................................................................................9
PANIC MODE.................................................................................................................................10
QUICK LOCKOUTTM........................................................................................................................10
COLD WEATHER MODE..................................................................................................................10
EXTENDED RUN TIME.....................................................................................................................11
LEDFLASHING..............................................................................................................................11
CONSTANT OUTPUT........................................................................................................................11
MISSING A START OR A STOP CONFIRMATION........................................................................12
ADVANCED FEATURES: INSTALLATION-PROGRAMMABLE OPTIONS..................................12
IGNITION-CONTROLLED DOOR LOCKS..............................................................................................12
SECURE LOCK...............................................................................................................................12
SAFE START..................................................................................................................................13
ENGINE RUN TIME.........................................................................................................................13
TURBO MODE................................................................................................................................13
“HOME VALETTM”MODE.................................................................................................................14
AUX1..........................................................................................................................................14
MULTI-CAR OPERATION..................................................................................................................14
OEM-STYLE ALARM......................................................................................................................15
INTRUSION CODES VIA HORN...........................................................................................................15
MULTI-LEVEL FEATURES .............................................................................................................16
TROUBLESHOOTING POOR TRANSMITTING RANGE...............................................................17
PARKING LIGHT FLASH TABLE...................................................................................................18
PROSTART LIMITED LIFETIME WARRANTY...............................................................................19

User Guide P.3
Introduction 
This is a state-of-the-art remote car starter system. The system is packed with advanced features
such as priority access to the driver’s door (commodity features), the Safe Start children safety
feature and SmartStart™.
SmartStart™ is a groundbreaking technology that enables your remote starter features to be
accessed by your smartphone. Features include keyless entry, trunk release, panic, remote
start/stop toggle and alarm notifications1. Note: SmartStart™ must be professionally installed. For
more information, see your nearest authorised Directed Canada dealer.
With many advanced functions, this product will satisfy any one of your expectations from high-end
commodity and security systems, without neglecting any standard feature commonly offered by
entry-level starters.
Whatis“eSH”Technology?
"eSH" technology uses Manchester decoding, along with advanced custom data filters, to help
reduce data-bit transfer errors. This filtering mechanism minimizes dropped commands by the
transceiver and develops more reliable range. By using narrow band filtering and unique software
driven noise filters, the radio set is able to achieve much better input sensitivity resulting in up to
2,000 feet of operating range.
VehiclePresets
Heater
When leaving the vehicle it is recommended to preset the accessory controls in preparation for the
next remote start. Settings for the blower motor (fan), front and rear, should not be left on HIGH. It
is recommended to leave the settings on LOW or MEDIUM instead.
WindshieldWipers&Radio&Headlights
Certain vehicles require the radio and / or windshield wiper and / or headlight circuits to become
energized while running under remote start. When leaving the vehicle you must ensure that the
windshield wiper and headlight switches are OFF. Leaving the headlight switch ON on certain
types of vehicles could cause them to remain ON even after remote starter shut down, resulting in
a dead battery.
UsingtheRemoteControl
Your remote car starter is equipped with a 6-button multi-channel remote control. It can operate
two independent vehicles equipped with a remote car starter.
LCDRemoteFunctions
The transmitter offers several command-confirmation and timer features. This section explains
some of the key functions available. The next section gives a summary of the button combinations
used to access the functions.
1Certain conditions apply. See your authorized Directed Canada dealer.

P.4 User Guide
Note: If you wish to exit a function while still in the process of accessing it, simply stops and wait at
least 10 seconds: the transmitter will return to its normal state.
The functions of the transmitter are as follows:
BasicVehicleOperations
Function
Button pressed
Icon
Sound
Instructions
/
description
Lock
1 beep Lock and arm the starter kill
Unlock 2 beeps Unlock and disarm the starter
kill
Trunk or aux 3 1 beep Trunk output
Start *
(see runtime
options below) + Melody Start the engine
Stop None Melody Stop the engine
Back light On for 5 seconds Press once
Cold weather + 1 beep See Cold Weather Mode
section
Remote valet + 1 beep See Vale mode section
Panic None 1 beep See Panic Mode section

Function Button:
. Turns On the backlight
. For accessing Multi-level
functions
UNLOCK Button:
Unlocks all Doors and
disarms the Starter Kill TRUNK Button:
Activates the Trunk
output (AUX3)
LOCK Button:
Locks all Doors and
arms the Starter Kill
START/STOP Button:
Starts or Stops the engine (Normal
functions
)
A
uxiliary Button:
•Activates
Panic Mode

User Guide P.5
TransmitterModeSelection
Function
Button pressed
Icon
sound
Instructions /description
Vibration mode Press and hold
and then press Vibrates 4x
A
larm clock mode
on/off + Melody
zPress once to have
alarm clock on
zPress twice to have
alarm clock off
Howtoaccessremote’sfunctionmenus:
User
Transmitter
1.Press until the remote beeps once Îappears on screen.
2.Press a 2nd time for 2 second and release ÎRemote beeps once and
appears on screen.
3.Press a 3rd time for 2 second and release ÎRemote beeps once and
appears on screen.
4.Press and hold button a 4th time until 2
beeps are heard. ÎYou have now accessed the first
function of the remote.
Press the button to toggle between remote’s functions menu:
a. Press the button to increase the value or to activate or deactivate a function or to toggle
through the melodies.
b. Press the to decrease the value or to activate or deactivate a function or to toggle through the
melodies.
c. To save modifications, do not touch any buttons for approx 5 to 10 seconds. There will be a
beep and the display will return to the time.
Function Menu Table:
Function 1:
A
djust clock time (hour and
minutes) Function
5: Timer
countdown
Function 2:
A
djust alarm clock (hour and
minutes) Function
6:
Melody selection for timer
countdown
Function 3:
Melody selection for the alarm
Function
7:
Turn ON/OFF timer
countdown
Function 4: Turn ON/OFF alarm cloc
k
TimerCountdownAdjustment
By pressing Icon
Sound
Instructions / description
+ 1st time
Melody 10 min parking countdown mode
+ 2nd time
Melody 20 min parking countdown mode
+ 3rd time
Melody 30 min parking countdown mode
+ 4th time
Melody 60 min parking countdown mode
+ 5th time
Melody 90 min parking countdown mode
+ 6th time
Melody 120 min parking countdown mode
+ 7th time
Melody Parking countdown off mode

P.6 User Guide
Once the Countdown is activated it will continue counting down until reaching 0:00. If the Timer has not
reached 0:00 and you are starting the vehicle, you should reset your Countdown Timer to 0:00 before starting
your vehicle as to avoid being startled.
ArminganddisarmingtheStarterKill
This added security feature will prevent the vehicle from starting with the Ignition key when the
starter kill is armed. If the system was installed with the starter kill option, you will not be able to
start the vehicle with the key unless the system has been unlocked first or put into Valet Mode
(page-9).
Note: If the Starter Kill is installed, the vehicle will benefit from a protection against starter
motor damage that could occur after remote-starting the engine should the user, by force of
habit, turn the ignition key to the CRANK position.
The Starter Kill (if installed) can be configured by the installer either to Passive Mode (so as to arm
automatically) or Active Mode (so as to require the user’s intervention for arming). By default, your
Remote Car Starter is configured to Passive Mode.
Passive mode:
To arm the Starter Kill, press the button on the transmitter, OR
1. In Passive Mode, the Starter Kill will automatically arm 1 minute (by default) or 3
minutes (if configured this way) after the ignition is turned OFF or once the last door is
closed (if the doors are monitored).
2. The LED on the antenna will flash quickly during the countdown preceding the activation
of the Starter Kill.
3. Once the activation countdown expires, the LED will send a series of quick double
flashes to indicate that the Starter Kill is now armed.
To disarm the Starter Kill, press the button on the transmitter.
•The Starter Kill will automatically rearm itself after 1 minute (by default) or 3 minutes (if
configured this way) if no door is left opened (if the doors are monitored) and the ignition
is not turned ON.
Active Mode:
To arm the Starter Kill, press the button on the transmitter.
1. The parking lights will flash once.
2. The LED on the antenna will flash slowly.
3. If remote door locks are installed, this will also lock the doors and arm the OEM-style
alarm.
To disarm the Starter Kill, press the button on the transmitter.
1. The parking lights will flash twice.
2. The LED on the antenna will remain OFF.
3. If remote door locks are installed, this will also unlock the doors.

User Guide P.7
RemoteStartingYourVehicle
SettingYourVehicleIntoReadyMode
If your vehicle has a manual transmission you must read the following indications. The unit must
first be set to Ready Mode in order to start the vehicle by remote. If the unit is not set to Ready
Mode, it cannot remote start the vehicle.
Please note that Ready Mode can be enabled by the remote or the handbrake, depending on the
option that was selected by your installer. Therefore, you must follow the appropriate procedure
between the two described below in order to set your vehicle into Ready Mode.
Once the system is set to Ready Mode, the vehicle can be remote started and stopped at any time.
The system will exit Ready Mode if a door, the hood or the trunk is opened, if the brake pedal is
pressed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON
(RUN) position.
To set the system to Ready Mode:
If Ready Mode is enabled by remote
If Ready Mode is enabled by handbrake
1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the
neutral position.
2. With the engine already running, apply the
parking brake once and release the brake
pedal.
2. With the engine already running, apply the
parking brake twice within 10sec.
Make sure to release the brake pedal.
The parking lights will flash 3 times quickly
and remain lit.
Skip to step 4.
3. Within 20 sec. of engaging the parking
brake, press and hold , or on
the transmitter.
The parking lights will flash 3 times quickly
and remain lit.
-
4. Remove the key: the engine will continue running.
5. Exit the vehicle and close all doors, hood and trunk.
6. Press for approx. 1 second either:
•to lock the doors and shut down the engine;
•to unlock the doors and shut down the engine;
•to shut down the engine without affecting the doors.
7. The icon will appear on your screen.

P.8 User Guide
Remotestarting
1. Press the button. The remote will beep once.
2. Approximately 5 seconds later, the remote will play a start melody to confirm the
remote starter’s activation.
If your vehicle has an automatic transmission and it does not start at the first attempt, the system
will shut down, wait a few seconds and try to start the engine again. There will be 3 start attempts
before the system gives up.
DrivingOff
With the vehicle running under remote control, press the button to disarm the starter kill (if
installed) and unlock the doors. Enter the vehicle and do the following:
•Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK
position while the engine is running. This would cause the starter motor to re-engage.)
•Press the brake pedal to disengage the remote starter unit.
You are now ready to drive off.
RemoteStarterFeatures
RemoteDoorLocks
If your system was installed with the Remote Door Locks option, you will have the convenience of
remote keyless entry.
To lock your doors and arm the starter kill (if installed):
1. Press and hold the button for approx. 1 sec.
2. The remote will beep once then display the icon to confirm that the doors have been
locked.
To unlock your doors and disarm the starter kill (if installed):
1. Press and hold the button for approx. 1 sec.
2. The remote will beep twice then display the icon to confirm that the doors have been
unlocked.
RemoteTrunkRelease
If your system was installed with the Remote Trunk Release option, you can open your trunk by
pressing the button until the remote displays on the screen. In addition, this will also
disarm the OEM style alarm.
IdleMode
Convenience feature: Idle Mode allows you to keep the engine running and the doors
locked while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the
Ignition Switch) while the engine is running.
If your vehicle has an automatic transmission, proceed as follows to set the system to Idle
Mode:

User Guide P.9
1. With the engine running, make sure to release the brake pedal and press the , or
button on the transmitter until the parking lights come ON.
2. Remove the ignition key from the ignition switch.
The engine will continue running.
3. Exit the vehicle and close all doors, hood and trunk.
4. Press the button to lock the doors, to arm the starter kill and to arm the OEM style
alarm.
If your vehicle has a manual transmission, Idle Mode can be activated through the same routine
as that used for Ready Mode (page-7); at the last step, press button to lock the doors, arm the
system and leave the engine running.
Note1: The engine will continue running until the user re-enters the vehicle or until the expiration of
the engine run time.
Note2: If the pre-programmed run-time expires or if the user shuts down the engine by remote
control, the vehicle will enter Ready Mode.
Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.
ValetModes
When the vehicle is in Valet Mode, the remote starter and alarm functionalities are disabled. If the
vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent the engine from
being remote-started accidentally.
Any of the following features will put your remote car starter into Valet Mode:
Ignition Valet: This feature allows you to put your system into Valet Mode by using the
ignition key.
Remote valet: This feature allows you to put your system into Valet Mode by using the
transmitter.
ToputthesystemintoValetMode
To put the system into Valet mode using the KEY (Ignition Valet Mode):
1. Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times
successively into the IGNITION/RUN and OFF positions.
2. The parking lights will flash three times.
3. Turn the ignition OFF.
4. The LED on the antenna will come ON solid to indicate that the vehicle has successfully
entered Valet mode.
5. The icon will appear on your LCD remote.
To put the system into Valet mode using the TRANSMITTER (Remote Valet Mode):
1. Press the and buttons simultaneously until the icon will appear on your LCD
remote.
2. The LED on the antenna will come ON solid to indicate that the vehicle has successfully
entered Valet mode.

P.10 User Guide
TotakethesystemoutofValetMode
To take the system out of Valet mode using the KEY (Ignition Valet Mode):
1. Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times
successively into the IGNITION/RUN and OFF positions.
2. The parking lights will flash twice.
3. Turn the ignition OFF.
4. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet
mode.
5. The icon will disappear on your LCD remote.
To take the system out of Valet mode using the TRANSMITTER (Remote Valet Mode):
1. Press the and buttons simultaneously until the icon will disappear from your
LCD remote.
2. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet
mode.
The system will warn you if someone attempts to remote start the vehicle while in Valet Mode:
The parking lights will:
Turn ON then OFF; then
Flash twice.
PanicMode
Note: Panic mode can only be activated if the horn has been adequately configured by the
installer.
In an emergency situation, you can activate panic mode by pressing and holding the AUXILIARY
BUTTON until the horn starts honking. If the vehicle is under a remote start, the engine will
shutdown automatically before setting off the horn. You can stop the horn by pressing:
(this will lock your doors and deactivate panic mode), or
(this will unlock your doors and deactivate panic mode).
Furthermore, the panic mode can be stopped by activating Valet Mode (page-9)
* Panic Mode will automatically shut down after 30sec.
QuickLockoutTM
(Also called Secure Panic.) For fast protection in emergency situations, the system will LOCK all
doors when you press the brake pedal while you hear the sound signal. (Quick Lockout is only
available when panic mode has been set off.)
ColdWeatherMode
If the vehicle has a Manual transmission, Ready mode (page-7) should be set before entering
Cold Weather. When cold weather mode is active, the engine starts every 2 hours and runs for 3
minutes (or for 8 or 20 minutes with diesel engines). Cold weather mode automatically ends after
24 hours. The vehicle must be set in ready mode (manual transmission) before the cold weather
mode can be activated.
To enter Cold Weather Mode:
1. Press the for 1 second and release. The remote will beep once and will
appear on the display.
2. Press and hold the button until the icon will appear on the display.

User Guide P.11
To exit Cold Weather Mode, do any one of the following actions:
•Open the hood.
•Start the engine by remote.
•Turn the ignition key to the IGNITION ON (RUN) position.
•Press the for 1 second and release. The remote will beep once and will
appear on the display.
•Press and hold the button until the icon will disappear on the display.
To verify whether the system is in cold weather mode:
•The icon should appear on your remote display.
•OR
•Press the brake pedal:
•If the vehicle is in cold weather mode, the parking lights will remain ON while the brake
pedal is pressed. (Automatic transmission ONLY).
ExtendedRunTime
While the vehicle is running under a remote start, press and hold the button until the remote
plays the start melody. This will reset the run time counter to zero and restart the run time cycle
from the beginning. The extended run time procedure can only be carried out once per
remote start.
To stop the vehicle, at any moment, simply press the button.
Example: If your remote car starter is programmed for a run time of 3 minutes and your vehicle
has been running for 2 minutes already, pressing the button will reset the counter
to zero and allow the engine to run for another cycle (in this case, 3 minutes).
LEDflashing
To disable the LED: Press and hold and simultaneously until the remote beeps once,
pause for 2 seconds, then beeps once again. Release the buttons. The parking light will flash 3
times.
To Enable the LED: Press and hold and simultaneously until the remote beeps once,
pause for 2 seconds, then beeps once again. Release the buttons. The parking light will flash 1
time.
Constantoutput
•Pressing and holding the button for more than 3 seconds will lock all doors and will send a
constant pulse as long as the button is held down (maximum of 15 seconds). This constant
pulse can be configured to activate certain functionalities such as rolling up the windows –
Please refer to your installer to see if your vehicle is compatible with this option.
•Pressing and holding the button for more than 3 seconds will unlock all doors and will send a
constant pulse as long as the button is held down (maximum of 15 seconds). This constant
pulse can be configured to activate certain functionalities such as rolling down the windows –
Please refer to your installer to see if your vehicle is compatible with this option.

P.12 User Guide
MissingaStartoraStopConfirmation
If you have not received a Start or the Stop confirmation after pressing the button, pressing the
button will refresh the display and will confirm if the vehicle was started or stopped.
If no Start Confirmation Was Received:
•Press the button:
¾The remote’s icon will start flashing
¾The icon and runtime time countdown will be displayed.
If no Stop Confirmation Was Received:
•Press the button:
¾The will be displayed
¾The remote’s icon and the runtime countdown will disappear.
AdvancedFeatures:InstallationprogrammableOptions
The remote starter was designed with flexibility and OEM integration in mind. With its program-
mable options, this unit can single-handedly control nearly any electrical system in your vehicle.
Caution: The programming of your system should be left to a professional. Changing any
one of the settings may affect the operation of your remote starter.
IgnitioncontrolledDoorLocks
This is an added security feature. If your Remote Car Starter was installed with the Ignition-
Controlled Door Locks option, the doors will automatically lock as soon as the ignition key is turned
to the IGNITION ON (RUN) position while the brakes are pressed. The remote car starter will also lock
any door that was unlocked and opened (then closed) the next time the brake pedal is pressed.
When the key is turned to the OFF position, the doors will automatically be unlocked.
SecureLock
Before it can remote-start your vehicle, the remote starter must first disarm the factory security
system. The secure lock feature may be required on certain vehicle models with factory security
systems thatautomatically unlock the doors when the security system is disarmed.
To keep your vehicle protected when the factory security system is disarmed for a remote start,
secure lock will relock your doors as soon as the vehicle has started. Once the engine run cycle
ends, secure lock will rearm your factory security system.

User Guide P.13
SafeStart
This feature will eliminate accidental remote starts, e.g. when children are playing with the
transmitter.
Safe start enabled: If this feature is enabled, the user must press the button twice within
3 seconds to remote-start the vehicle.
Swap start: If this feature is enabled;
1. Press the for 1 second and release.
2. The remote will beep once and will appear on the display.
3. Press to remote start the vehicle.
The AUX 2 output can be activated by pressing the button.
EngineRunTime
If you have a gas engine, your remote starter can be programmed to run the engine for 3, 15, or
25 minutes (15 minutes by default). If you have a diesel engine, the remote starter can be
programmed to run the engine for 8, 20, or 30 minutes (20 minutes default).
TurboMode
If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user
leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it
is shut down by remote control), then shut down the engine.
If your vehicle has an automatic transmission, proceed as follows to set the system to Turbo
Mode:
1. With the engine running, make sure to release the brake pedal and press the ,
or button on the transmitter until the parking lights come ON.
2. Remove the ignition key from the ignition switch.
The engine will continue running.
3. Exit the vehicle and close all doors, hood and trunk.
4. Press the button; this will lock the doors, arm the OEM-style alarm (if configured|)
and confirm that the vehicle is in Turbo Mode.
5. The engine will shut down after 60 seconds.
If your vehicle has a manual transmission, follow all steps of the Ready Mode routine (page-7) to
activate Turbo Mode. At the last step,
•Press to lock the doors and have the engine shut down after 60 seconds;
The parking lights will flash 3 times and remain lit.
The OEM-style alarm and starter kill (if configured) will be armed.
•Press to unlock the doors and have the engine shut down after 60 seconds;
The parking lights will flash 3 times and remain lit.
•Press to shut down the engine without affecting the doors.
Note: The vehicle will enter Ready Mode once the engine run time expires.

P.14 User Guide
“HomeValetTM”Mode
If configured at installation, this feature will remotely set the vehicle to a no-remote-start mode: if
the vehicle is parked indoors there is no danger of it starting accidentally by remote control. If the
vehicle has a manual transmission, it should be set into ready mode before activating the Home
Valet™.
Note: Once the Home Valet Mode is activated, the vehicle will not start by remote, but the
OEM alarm functions will remain active.
To take the system into home valet mode:
1. Press the or button.
2. Within 3 seconds, press the and buttons simultaneously until the transmitter beep
once and display icon on the LCD screen.
To take the system out of home valet mode:
•Turn the ignition key to the IGNITION ON (RUN) position.
The system will warn you if someone attempts to start your vehicle while it stands in home valet
mode. The parking lights will:
Turn ON then OFF; then
Flash twice, pause; then
Flash twice again.
AUX1
Note: This 500 mA negative Aux 1 output can be used for many different applications
Priority door:
This great feature allows the user to unlock solely the driver’s door with a single press of the
button on the transmitter, and to unlock the other doors, if desired, by pressing the
button for a second time.
The output will provide a 1-second negative output when the button is pressed a second
time on the transmitter.
Horn Confirmation:
AUX 1 can be programmed to trigger the horn every time the button is pressed, or when
the button is pressed twice within 3 seconds. When horn confirmation is activated, panic
mode is enabled. If horn confirmation is disabled, panic mode will not be available.
MulticarOperation
This option allows the owner of two vehicles, both equipped with the same remote starter model, to
control both systems with a single remote control. To control the second vehicle:
•Press + :..................................................................LOCK
•Press + :...................................................................UNLOCK
•Press + :........................................................................................START
•Press + :.....................................................................STOP
•Press ¾+ :......................................................TRUNK
or

User Guide P.15
•Press ¾¾+ :.................................................LOCK
•Press ¾¾+ :..................................................UNLOCK
•Press ¾¾+ :...................................................................START
•Press ¾¾+ :....................................................STOP
•Press ¾¾+ :..................................................TRUNK
Start/Stop While in Safe Start Mode
Function
Button press
Icon
Sound
Description
Start on safe start
mode + x 2 + Melody
Press +
simultaneously twice within 3
seconds. Press for 1 sec- a
beep will be heard- then
press 1sec and a melody will
be heard again.
Stop on safe start
mode + None Melody
Note: Your remote control must be configured for second car operation by the installer.
OEMStyleAlarm
The OEM-style alarm (if configured by your installer) monitors the doors, hood and ignition switch
of your vehicle. It will sound the horn if a door or the hood is opened, or if the key is turned in the
ignition.
•To arm the OEM-style alarm, press the button on the transmitter.
-The OEM-style alarm will ONLY arm if the button on the transmitter is pressed.
- The LED on the antenna will flash slowly to indicate that the OEM-style alarm is now
armed.
•To disarm the OEM-style alarm, press the button on the transmitter.
- To stop the horn from sounding if the OEM-style alarm is triggered, press the or
button, or put the systemin and out of Valet Mode (page-9)
IntrusionCodesviahorn
The system monitors the following:
•Doors
•Hood
•Ignition
Note: If an intrusion has occurred the HORN will sound for a maximum of 1minute.
If an intrusion has occurred and pressed, the horn provides an intrusion code corresponding to
the type of intrusion that occurred.
Diagnostic table:
1x = power interruption 4x = Doors intrusion
3x = Hood 6x = Ignition

P.16 User Guide
MultiLevelFeatures
Basic Features (press the button 1X) Level 1
¾............................................................. aux 2
¾............................................................. cold weather
Multi-Car Operation (press the button 2X) Level 2
¾¾............................... :2
nd car lock
¾¾............................... :2nd car unlock
¾¾............................... :2
nd car start/stop
¾¾............................... :2
nd car trunk
Customized Features (press the button 3X) Level 3
(May not be compatible with some vehicles)
Your installer can add customized features such as turning on the radio, opening sliding doors, etc.
¾¾¾...................... :customized feature 1
¾¾¾...................... :customized feature 2
¾¾¾...................... :customized feature 3
¾¾¾...................... :customized feature 4
Accessing the Multi-Level Features and Other Transmitter Functions
xTo access a Level 1 feature, press and hold the button until you hear a “beep”; within three
seconds of hearing the “beep”, release the button. will be displayed. This display
means that you are now in Level 1. Simply press the corresponding button to access the
desired feature.
xTo access a Level 2 feature, press and hold the button until you hear a “beep within three
seconds of hearing the “beep”, release the button and press and release the button
once more. will be displayed. This display means that you are now in Level 2. Simply
press the corresponding button to access the desired feature.
xTo access a Level 3 feature, press and hold the button until you hear a “beep”; within three
seconds of hearing the “beep”, release the button and press and release the button
two more times. will be displayed. This display means that you are now in Level 3.
Simply press the corresponding button to access the desired feature.
xTo access the transmitter functions (clock and alarm adjustments), press and hold the
button until you hear a “beep”; within three seconds of hearing the “beep”, release the
button and press and release the button three more times. There will be two quick “beeps”
indicating that you are now in the transmitter functions adjustment menu. The Hour position will
be flashing. Simply press and release the button until you reach the desired location and
proceed with the adjustment by pressing the or buttons.
Your installer can customize the system as to personalize these multi-level features in an order that
best suits you. Your options are:

User Guide P.17
Option 1:
Level 1 (requires pressing the button 1X) ÆMulti car operation
Level 2 (requires pressing the button 2X) ÆBasic features
Level 3 (requires pressing the button 3X) ÆCustomized features
Option 2 (by default):
Level 1 (requires pressing the button 1X) ÆBasic features
Level 2 (requires pressing the button 2X) ÆMulti car operation
Level 3 (requires pressing the button 3X) ÆCustomized features
Option 3:
Level 1 (requires pressing the button 1X) ÆCustomized features
Level 2 (requires pressing the button 2X) ÆMulti car operation
Level 3 (requires pressing the button 3X) ÆBasic features
Option 4:
Level 1 (requires pressing the button 1X) ÆBasic features
Level 2 (requires pressing the button 2X) ÆCustomized features
Level 3 (requires pressing the button 3X) ÆMulti car operation
Example: If the multi-level feature was set to option 3, the setup would be as follows:
For “basic features”:
xTo access the aux. 2 feature, the user needs to press on the button three (3) times followed
by the button.
xTo access cold weather mode, the user needs to press on the button three (3) times
followed by the button.
TroubleshootingPoorTransmittingRange
Many factors may affect the operating range of the transmitter. Some of these are:
•The condition of the battery in the transmitter.
•The operating environment (for example: downtown radio-frequency noise, airports, cellular
phone towers…)
•Metal: any type of metal will affect operating range. This includes the metal in the car.
•The shape of the vehicle can affect range as well; vans in general have an especially poor
range.
•The shape of the roof and A-pillars brings about considerable radio-frequency deflection (in
this case the signal from the remote control). As a result, the direction in which the vehicle is
facing in relation to the remote control can affect the range. Straight on – standing in front of
the vehicle – generally gives you the greatest range; the second best performance is from the
back. Using the remote control from either side of the vehicle will usually give the lowest
range.
•The range will be significantly lower in a crowded parking lot than in open space.
•Always hold the transmitter high, approximately at shoulder height. Holding the transmitter
against your chin will also increase your range: your head acts as an antenna.

P.18 User Guide
•The operating range will be somewhat lower on vehicles equipped with an aftermarket or
factory alarm.
ParkingLightFlashTable
Parking lights flashes Description
1
•Doors locked.
•Trunk released.
•Start signal received from the remote.
•Runtime has expired
2 slow •Shutdown by remote
2 fast •Doors unlocked
•Valet mode is deactivated
3 slow •Runtime is extended.
3 fast •Valet mode activated.
4 fast •Shutdown by brake
•A remote start was attempted while the brake pedal is engaged.
10 fast •Shutdown by hood
•A remote start was attempted while the hood is open.
ON Îtwice •Cold weather mode deactivated
ON Î3 times •Cold weather mode activated.
Solid ON •Engine is running under remote start.
Flash for 30 sec. •Panic mode is triggered.
Flash for 60 sec. •Alarm is triggered.
ON Îtwice Îtwice •A remote start was attempted while the system is in home valet.

User Guide P.19
PROSTART LIMITED LIFETIME WARRANTY
REMOTE STARTERS:
As the manufacturer, DIRECTED ELECTRONICS, CANADA INC. (“Directed”) warrants to the original consumer purchaser only (non-transferable)
that the remotestarter module (control box)shall be free from defectsin materialsand workmanshipfor as long as the original consumer
purchaser continuously owns the vehicle in which the remote starter was originally installed, as specified below:
1) For the first year after the date of purchase, as specified by the date on the original proof of purchase, Directed will replace the
remote starter module freeof charge with anew remote starter module. Consumers shall providea copy of theproof of purchase at
the point of purchase for the exchange to take place. The remainder of the coverage period of the original warranty will apply to the
new module.
2) For the second year after the date of purchase, as specified by date on the original proof of purchase, Directed will replace the
remote starter module freeof charge with a repaired orrefurbished remote startermodule. Allproduct returnsto Directed for
warranty service requirea Return Merchandise Authorization (RMA). This RMA must be issuedprior to returning product to
Directed. Products returned without this RMA number will be refused & returned to you at your expense. Consumers shall send the
module (only)and a copy ofthe proof of purchase, freight prepaid, along with theirname, address and telephone number, to the
PROSTART SERVICE CENTER for the exchange to take place. MODULES RETURNED TO THE POINT OF PURCHASE AFTER
THE ONE-YEAR REPLACEMENT PERIOD WILL NOTBE ACCEPTED. A module will be returned to the consumer, freight collect,
within 4 weeks of receipt of the module. The remainder of the coverage period of the original warranty will apply to the exchanged
module. Directed will not be heldresponsible for modules sent without a proof of purchase. Directed will notbe held responsible for
modules lost ordamaged while in transit.
3) For the third year andany consecutive year after the date ofpurchase, as specified by the date on theoriginal proof of purchase,
Directed will provide to the original consumer purchaser a repaired or refurbished remote starter module, for arepair and
shipping/handling charge of $45.00 plus applicable taxes, a cheque or money order made payable to DIRECTED ELECTRONICS,
CANADA INC must accompany the remote starter module. A module will be returned to the consumer, freight prepaid, within 4
weeks of receipt of the module. Directed will not be held responsible for modules sent without a cheque or money order and/or proof
of purchase. The consumershould follow the same procedure as in(2), and allconditions apply asin (2).
ACCESSORIES:
Directed warrants to the original consumerpurchaser only(non-transferable) that it will replace any Directed accessory part for a one-year period
from date of purchase. Accessories will only be replaced if proven defective in material or workmanship, and if, when the accessory is returned to the
point of purchase, the retailer is provided with a copy of the proof of purchase.
THE WARRANTY IS VOID IF:
1) The product hasbeen damaged, alteredin any way ortampered with, without theexplicit written consentof a
Directed technician. For remote starter modules, this includes the opening or removal of the plastic covering of the
module, or the removal oralteration ofthe barcode label on the plastic covering of the module.
2) The product isdamaged due to accident,fire, flood, shipping and handling, misuse, neglect, or otherconditions
beyond the control of Directed.
3) The product hasbeen installed or repaired by anyone other than a certified technician.
4) The product has been improperly installed or used.
THE WARRANTY DOES NOT COVER:
1) Batteries.
2) Scratched or worn transmitter cases.
3) Installation and/or removal charges for all remote starter modules and accessories.
4) Shipping and handling charges incurred for product exchange or replacement.
5) Any material damages other than to the product itself.
6) Harnessing, LED lights, switches, inverters, relays, etc.
THIS LIMITED LIFETIME WARRANTY SHALL CONSTITUTE THE SOLE LIABILITY OF DIRECTED FOR OUR PRODUCTS, AND IS IN LIEU OF
ALL OTHER WARRANTIES, EXPRESSED ORIMPLIED. THERE ARE NO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO ASSUME FOR AUTOSTART ANY OTHER LIABILITY
WITH RESPECT TO THE SALE OR USE OF OUR PRODUCTS. DIRECTED’S LIABILITY, WHETHER BASED ON CONTRACT, TORT,
WARRANTY, STRICT LIABILITY, OR ANY OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT
FOR DAMAGE IS THE BASIS OF THE CLAIM. UNDER NO CIRCUMSTANCE WILL AUTOSTART, ITS DISTRIBUTORS OR THEIR AGENTS
BEAR ANY LIABILITY WHATSOEVER FOR INCIDENTAL OR CONSEQUENTIALDAMAGES.
The parties hereto elect that any dispute regarding the present documentbe submitted to the appropriate Court located in the Province of Quebec,
District of Montreal. The parties hereto agree that thisdocument is governed by and interpreted inaccordance with the law of Quebec. If the
purchaser is located in a provinceof Canada other than Quebec, all matters dealing with the warranty of quality will be governed byand interpreted
in accordance with the law of Ontario. If the purchaser is located outside Canada, all matters dealing with the warranty of quality will be governed by
and interpreted in accordance with the United NationsConvention on Contracts forthe International Saleof Goods (the “Vienna Convention”).
PROSTART SERVICE CENTRE / WARRANTY PROGRAM
2750, Alphonse-Gariépy
Lachine, Québec
H8T 3M2
Phone: [phone] (Return Merchandise Authorization and/or Warranty- related questions only)