Provision ISR NVR-8200(1U) User manual

PROVISION-ISR
NVR-8200(1U)
User Manual
8CH 720P Real-Time Conventional NVR
For H.264 8-channel network video recorder
All rights reserved

CAUTION
Read this user manual carefully and use the device correctly and safely.
NVR warranty requires an intact serial number located on the bottom of the NVR and a valid
invoice or receipt with the date of purchase.
We do not warrant all the content is correct.
The contents of this manual may be out-dated.
If you are not certain of something, you should contact technical support before making any
change, or installing the NVR.
This device should be operated only from the type of power supply indicated on the marking
label. The voltage of the power must be verified before using.
If you plan not to use the NVR for a long time, shut it down and unplug the power cable.
Don't install this device close to a heat sources (e.g. radiators, heat registers, stoves, ec't).
Do not install this device near water.
Clean only with a dry cloth.
Do not block the ventilation openings.
Place the device in a ventilated place.
Do not unplug the DVR when the device is working: the correct method to shut down DVR is
to perform software shutdown by pressing the “shut down” button from the main menu.
PROVISION-ISR NVR-8200(1U) is intended for indoor use only.
Do not expose the NVR-8200(1U) to rain or moist conditions.
If any solid or liquid gets inside the NVR, shut down the NVR and unplug the power supply as
soon as possible, and get it checked by a qualified technician.
Refer all servicing to qualified service personnel.
Do not try to repair the device by yourself without technical aid or approval.
This manual is suitable for the 8 channel Network video recorder NVR-8200(1U)

Contents
1Introduction ............................................................................................................................... 6
1.1 NVR Introduction ........................................................................................................................ 6
1.2 Main Features .............................................................................................................................. 6
2Hardware Installation ............................................................................................................... 7
2.1 Install Hard Drive &DVD Writer................................................................................................. 8
2.1.1 Install Hard Drive.................................................................................................................. 8
2.1.2 Install DVD Writer ................................................................................................................ 8
2.2 Front Panel Descriptions.............................................................................................................. 9
2.3 Rear Panel Instructions .............................................................................................................. 10
2.4 Remote Controller...................................................................................................................... 12
2.5 Control with Mouse ................................................................................................................... 14
2.5.1 Connect Mouse.................................................................................................................... 14
2.5.2 Use Mouse........................................................................................................................... 14
3Basic Function Instruction...................................................................................................... 15
3.1 Startup and Shutdown................................................................................................................ 15
3.1.1 Startup.................................................................................................................................. 15
3.1.2 Shutdown............................................................................................................................. 15
3.2 Login.......................................................................................................................................... 15
3.3 Live preview.............................................................................................................................. 16
3.4 Live playback............................................................................................................................. 16
4Add IP Cameras....................................................................................................................... 18
5Main Menu Setup Guide......................................................................................................... 20
5.1 Basic configuration.................................................................................................................... 21
5.1.1 System ................................................................................................................................. 21
5.1.2 Date & Time ........................................................................................................................ 22
5.1.3 DST ..................................................................................................................................... 22
5.2 Live Configuration..................................................................................................................... 23
5.2.1 Live...................................................................................................................................... 23
5.2.2 Main Monitor....................................................................................................................... 24
5.2.3 Mask.................................................................................................................................... 24
5.3 Record Configuration................................................................................................................. 25
5.3.1 Enable.................................................................................................................................. 25
5.3.2 Record Bitrate...................................................................................................................... 26
5.3.3 Time..................................................................................................................................... 27
5.3.4 Stamp................................................................................................................................... 27
5.3.5 Recycle Record.................................................................................................................... 28
5.3.6 Snap..................................................................................................................................... 28
5.4 Schedule Configuration.............................................................................................................. 28
5.4.1 Schedule .............................................................................................................................. 28
5.4.2 Motion Schedule.................................................................................................................. 29
5.4.3 Sensor Schedule................................................................................................................... 30
5.5 Alarm Configuration.................................................................................................................. 30
5.5.1 Sensor Alarm ....................................................................................................................... 30
5.5.2 Motion Alarm ...................................................................................................................... 32
5.5.3 Other Alarm......................................................................................................................... 33
5.5.4 Alarm Out............................................................................................................................ 33
5.6 Network Configuration .............................................................................................................. 34
5.6.1 Network............................................................................................................................... 34
5.6.2 Email ................................................................................................................................... 35

5.6.3 Server................................................................................................................................... 36
5.6.4 Other Settings ...................................................................................................................... 36
5.7 User Management Configuration............................................................................................... 39
5.8 Advanced ................................................................................................................................... 41
5.8.1 Reset.................................................................................................................................... 41
5.8.2 Import/Export ...................................................................................................................... 41
5.8.3 Block/Allow List ................................................................................................................. 41
6Search, Playback & Backup.................................................................................................... 42
6.1 Time Search ............................................................................................................................... 42
6.2 Event Search.............................................................................................................................. 43
6.3 File Management ....................................................................................................................... 44
6.4 Search by Image......................................................................................................................... 44
6.5 Backup....................................................................................................................................... 45
7Manage NVR............................................................................................................................ 46
7.1 Check System Information......................................................................................................... 46
7.1.1 System Information ............................................................................................................. 46
7.1.2 Event Information................................................................................................................ 46
7.1.3 Log Information................................................................................................................... 47
7.1.4 Network Information ........................................................................................................... 47
7.1.5 Online Information .............................................................................................................. 47
7.1.6 Record Information.............................................................................................................. 47
7.2 Manual Alarm ............................................................................................................................ 47
7.3 Disk Management...................................................................................................................... 47
7.4 Upgrade...................................................................................................................................... 47
7.5 Logoff ........................................................................................................................................ 48
8Remote Surveillance................................................................................................................ 48
8.1 IE Remote Surveillance ............................................................................................................. 48
8.1.1 On LAN............................................................................................................................... 48
8.1.2 On WAN.............................................................................................................................. 49
8.2 Remote Surveillance through Apple PC..................................................................................... 49
8.2.1 On LAN............................................................................................................................... 50
8.2.2 On WAN.............................................................................................................................. 51
8.3 Remote Preview......................................................................................................................... 52
8.4 Remote Playback & Backup ...................................................................................................... 54
8.4.1 Remote Playback................................................................................................................. 54
8.4.2 Remote Backup.................................................................................................................... 57
8.5 Remote System Configuration................................................................................................... 57
8.6 Tools........................................................................................................................................... 58
8.7 Remote Information................................................................................................................... 58
8.8 By Phones with iPhone OS........................................................................................................ 60
8.9 By Phones with Android ............................................................................................................ 66
Appendix A FAQ ......................................................................................................................... 69
Appendix B Calculate Recording Capacity .............................................................................. 73
Appendix C Compatible Devices ............................................................................................... 74
Appendix D NVR Specifications................................................................................................ 75
Notes: .............................................................................................................................................. 76

1Introduction
1.1 NVR Introduction
This series of devices are standard 8 CH real-time 1080P/720P/D1 high resolution NVR,
which adopt the most advanced SOC technique to ensure high definition recording in each
channel and realize outstanding robustness of the system. The series of product support 8 CH
IP input, simultaneous 8 CH playback, and HDMI 1080 P high resolution display. All of these
features make the device meet different security requirements of home, financial, commerce,
enterprise, transportation and government, etc.
1.2 Main Features
COMPRESSION FORMAT
Standard H.264 compression with low bit rate and better image quality
LIVE SURVEILLANCE
Support HDMI/CVBS/ VGA output
8 CH 1080@15fps or 4CH 1080P @ 30 fps or 8 CH 720P@ 30fps IP video input
Support channel security by hiding live display
Display the local record state and basic information
Support USB to make full control
RECORD MEDIA
Support two SATAHDDs to record for a longer time without any limitation
BACKUP
Support USB 2.0 devices to backup
Support built-in SATA DVD writer to backup
Support saving recorded files with AVI standard format to a remote computer through
internet
RECORD & PLAYBACK
Record modes: Manual, Schedule, Motion detection and Sensor alarm recording
Support recycle after HDD full
Resolution, frame rate and picture quality are adjustable
Two record search mode: time search and event search.
Support 8 screen playback simultaneously
Support deleting and locking the recorded files one by one
Support remote playback in Network Client through LAN or internet
ALARM
8 CH alarm inputs and 1 generic output
Support schedule for motion detection and sensor alarm
Support pre-recording and post recording
Support linked channels recording once motion or alarm triggered on certain channel

SECURITY
Customize user right: log search, system setup, two way audio, file management, disk
management, remote login, live view, manual record, and playback.
Support 1 administrator and 63 user designated usernames and passwords.
Support event log recording and checking, events unlimited
NETWORK
Support TCP/IP, DHCP, PPPoE, DDNS protocol
Support IE browser to do remote view
Support setup client connection amount
Support dual stream. Network stream is adjustable independently to fit the network
bandwidth and environment.
Support picture snap and color adjustment in remote live
Support remote time and event search, and channel playback
Support remote full menu setup, changing all the NVR parameters remotely
Support mobile surveillance by phones with iPhone & Android OS
Support CMS/NVMS to manage multi devices on internet
2Hardware Installation
Check the unit and the accessories after getting the device. Please don’t power up the unit till

the physical installation is complete.
2.1 Install Hard Drive &DVD Writer
2.1.1 Install Hard Drive
Notice: 1. This series supports two SATA hard drives. Please use the hard drive the
manufacturers recommend specially for security and safe field.
2. Please calculate HDD capacity according to the recording setting. Please
refer to “Appendix B Calculate Recording Capacity”.
Step1: Loosen the screws to open the top cover of the NVR.
Step2: Connect the power and data cables and place the HDD onto the bottom case as Fig 2-1.
Step3: Secure the HDD with the screws as Fig 2-2.
Fig 2-1 Connect HDD Fig 2-2 Screw HDD
Note: For convenience installation, please connect the power and data cables first and
then secure the HDD by tightening the screws.
2.1.2 Install DVD Writer
Notice: 1. The writers must be the compatible devices we recommend. Please refer to

“Appendix C Compatible Devices”
2. This device is only for backup.
Step1: Loosen the screws to open the top cover of the NVR.
Step2: Connect the power and data cables and place the DVD writer onto the bottom case as
Fig 2-3.
Step3: Secure the DVD writer with the screws as Fig 2-4.
Fig 2-3 Connect the DVD Writer Fig 2-4 Screw the Writer
2.2 Front Panel Descriptions
Notice: The front panel descriptions are only for reference; please make the object as
the standard.

Type
Name
Description
Work
state
indicator
Power
The power indicator turns blue when NVR is powered up.
HDD
The light turns blue when HDD is writing and reading.
Net
The light turns blue when it is able to access the network.
Backup
The light turns blue when backing up files and data.
Play
The light turns blue when playing video.
REC
The light turns blue when recording.
Function
button
Number 1~9
Input number 1~9 or choose camera
MENU/+
1. Enter menu in live 2. Increase the value in setup
BACKUP/-
1. Decrease the value in setup 2. Enter backup mode in live
0/10+
Input number 0, 10, and the above number together with other digital keys
Focus
1. Record manually 2. FOCUS function enables at PTZ mode.
Speed
1. Rewind key 2. SPEED function enables at PTZ mode
IRIS
1. Enter play interface 2. IRIS function enables at PTZ mode
P.T.Z
1. Fast forward 2. Enter PTZ mode in live
Input
button
Direction button
Change direction to select items.
Multi-screen
Change screen display mode like1/4/8 channel.
Enter button
Confirm selection.
IR
receiver
IR
For remote controller
USB
USB port
To connect external USB devices like USB flash, USB HDD for backup or
update firmware; or connect to USB mouse.
2.3 Rear Panel Instructions

Fig 2-6 Rear Panel for 8-ch
Item
Name
Description
1
DC12V
Power input
2
GND
Grounding
3
Alarm Out
Relay Output. Connect to external alarm.
4
Alarm in
Alarm Inputs for connecting sensors
5
K/B
Connect to keyboard, A is TX+, B is TX-
6
P/Z
Connect to speed dome, Y is TX+, Z is TX- (unavailable temporarily)
7
Audio in
1 CH audio input
8
HDMI port
Connect to high-definition display device
9
VGA port
VGA output, connect to monitor
10
USB port
Connect to external USB devices like USB flash, USB mouse, etc
11
LAN
Network port
12
Video Out
Connect to monitor
13
Audio out
Audio output, connect to the sound box
Alarm Out Connection:
Pull out the green terminal blocks and loosen the screws in the alarm out port. Then insert the
wires of the alarm output devices into the port of NO and COM separately. Finally, tighten the
screws. The external alarm output devices also need power supply, you can connect the power
supply as per the following figures.

2.4 Remote Controller
It uses two AAA size batteries.
Open the battery cover of the Remote Controller.
Place batteries. Please take care of the polarity (+ and -).
Replace the battery cover.
The interface of remote controller is shown in Fig 2-9 Remote Controller.
Fig 2-9 Remote Controller
Operation processes with remote controller to control multi-NVR
Button
Function
Power
Button
Switch off—to stop NVR. Use it before turning off the
power
Record Button
To record manually
-/-- /0-9 Digital
Button
Input number or choose camera
Fn1 Button
Unavailable temporarily
Multi Button
To choose multi screen display mode
Next Button
To switch the live image
SEQ
To enter into auto dwell mode
Audio
To enable audio output in live mode
Switch
To switch the output between BNC and VGA
Direction button
To move cursor in setup or pan/title PTZ
Enter Button
To confirm the choice or setup
Menu Button
To enter into menu
Exit Button
To exit the current interface
Focus/IRIS/Zoo
m/PTZ
PTZ Control button
Preset/Cruise/Tr
ack/Wiper/Light
Button
Enter preset/cruise/Track/Wiper/Light setup in PTZ mode.
You shall press PTZ button to go into PTZ setup mode. Then
select a channel and press PTZ button again prior to enabling
these buttons
Clear Button
To return to the previous interface
Fn2 Button
Unavailable temporarily
Info Button
Get information about NVR like firmware version, HDD
information
To control playback. Play/Pause/Stop/Previous Section/Next
Section/Rewind/Fast Forward
Snap Button
To take snapshots manually
Search Button
To enter into search mode
Cut Button
To set the start/end time for backup in playback mode
Backup Button
To enter into backup mode
Zoom Button
To zoom in the images
PIP Button
To enter into picture in picture setting mode

The default device ID of the NVR is 0. It’s not necessary to reset the device ID when a remote
is to be used to control a single NVR. However when controlling multiple NVRs with multiple
remote controllers, you would need to configure the device ID, please refer to below steps:
Activate remote controller to control the NVR: Turn the IR sensor of the remote controller
towards the IR receiver on the front panel, press the number key 8 twice on the remote, then
input device ID of the NVR to be controlled (Range from: 0-65535; the default device ID is 0)
press ENTER to confirm.
You can check the device ID of a NVR from System SetupBasicDevice ID. You can also
set multiple NVRs with the same device ID however this can cause interference if the NVRs
are kept close to each other.
Key points to check in case the remote doesn’t work.
1. Check batteries polarity and the remaining charge in the batteries.
2. Check IR controller sensor for any masking.
3. Check the ID of the remote with respect to the NVR.
If it still doesn't work, please try using a good known remote, or contact your dealer.

2.5 Control with Mouse
2.5.1 Connect Mouse
It supports USB mouse through the ports on the rear panel.
If mouse is not detected or doesn't work, check below steps:
1. Make sure the mouse is plugged in the USB mouse port.
2. Try with a good know mouse.
2.5.2 Use Mouse
During live:
Double-click on any camera window to see the full screen. Double-click again to return to the
previous screen.
Right click to reveal the control menu on the screen. Right click again to hide the menu.
In Configuration:
Click to enter a particular option. Right click to cancel the option or to return to the previous
menu.
In order to input a value in a particular screen, move cursor to the input box and click. An
input window will appear as Fig 2-10. It supports digits, alphabets and symbols input. Click
Shift button to input Capital letters and symbols; click Shift button again to return.
It supports mouse drag. Take setting up motion detection area for example: Click customized,
hold down the left button and drag to set motion detection area.
Fig 2-10 Digital Numbers and Letters Input Window
In Playback:
Click to choose the options. Right click to return to live mode.
In Backup:
Click to choose the options. Right click to return to previous picture.
In PTZ Control:
Click left button to choose the buttons to control the PTZ. Click right button to return to live.
Note: Mouse is the default tool for all operations unless an exception, as indicated.

3Basic Function Instruction
3.1 Startup and Shutdown
Please make sure all the connections are done properly before you power on the unit. Proper
startup and shutdown are crucial to expanding the life of your NVR.
3.1.1 Startup
Step 1: Connect with the power.
Step 2: The device will boot and the power LED would turn blue.
Step 3: AWIZZARD window will pop up and show some information about time zone, time
setup, network configuration, record configuration and disk management. You can set up here
and refer to the concrete setup steps from the corresponding chapters. If you don’t want to set
up Wizard, please click Exit button to exit.
Note: The default output is HDMI output. Hold and press ESC key to switch the video
output.
3.1.2 Shutdown
You can shut down the device by using IR remote controller and mouse.
By IR remote controller:
Step 1: Press Power button. This will bring up a shutdown window. The unit will shut down
by clicking “OK” button.
Step 2: Disconnect the power.
By mouse:
Step 1: Click button and select “Shut Down” icon. This will take you to a shutdown
window.
Step 2: Click OK. Then the unit will power off after a while.
Step 3: Disconnect the power.
3.2 Login
You can login or log off the NVR system. Once logged off you cannot do any other operation
except changing the multi-screen display.

Fig 3-1 Login
Notice: The default user name and password is “admin” and 123456”.
For complete operational steps for changing password, adding or deleting user please
refer to section 5.7 User management Configuration.
3.3 Live preview
Fig 3-2 Live Preview Interface
3.4 Live playback
Click Play button to playback the record. Refer to Figure 3-3. You can do complete
operation by clicking the buttons on screen.
Symbol
Meaning
Green
Manual record
Yellow
Motion detection record
Red
Sensor Alarm record
Blue
Schedule record

Fig 3-3 Live Playback

4Add IP Cameras
This chapter mainly introduces how to connect multiple IP cameras through NVR. Once you
finish adding IP cameras, you can see the live images through the monitor of the NVR.
To add IP cameras via LAN:
Step 1: Please Enter into MenuIP Camera tab. Refer to Fig 4-1. Click “Search” button to
search the devices in the same local network.
Fig 4-1 Device Management
Step 2: Enter into the search tab. Click “Refresh” to refresh the searched devices. You can
modify the IP address of the searched device by checking the device and clicking “Setup”
button.
Fig 4-2 Search Devices
Note: If the network of IP cameras and NVR are in LAN, their IP address must be in the
same network segment. For example: If the IP address of NVR is 192.168.013.057, the
IP address of IP camera must be 192.168.013.XXX.
Step 3: Choose the searched devices and click “OK” button to add these devices. The added

cameras will be listed in the device management interface.
Step 4: Choose the camera device and click “Setup” button to enable the camera. Refer to Fig
4-3. Check the “enable” checkbox, select channel and input the username and password of this
device. Then click “OK” to save settings.
Fig 4-3 Add Device
To add IP cameras via WAN:
Step 1: Please enter MenuIP Camera tab. Refer to Fig 4-1.
Step 2: Click “Add”button to pop up a window similar to Fig 4-3. You need to check
“Enable” box, select channel, manufacturer and product model and manually input IP address,
server port, username and password of this device.
Note: If the NVR and the IP cameras you want to add are in WAN, the IP address of the
IP camera input here must be WAN IP. You should forward the LAN IP address and port
of the IP camera in the router and use its WAN IP address, provided that the IP camera
is in local area network, otherwise, the NVR cannot connect this IP camera.

5Main Menu Setup Guide
Click right mouse or press ESC/Stop button on the front panel to display the main menu toolbar
on the bottom of the screen. Refer to Fig 5-1:
Fig 5-1 Main Menu Toolbar
Click the icon beside the screen mode to display a channel select dialog.
Screen Mode: You can choose a screen display mode to show the live images.
PIP: Click this button to set PIP. Click this button to choose the bigger picture and then click
the little PIP button beside the word “None” to set the smaller picture. After that, you can see a
picture in picture.
Dwell: Dwell means to display live images from different cameras in a sequence. The images
may be displayed as a single channel or in a grid fashion from different cameras. Dwell mode
is enabled only when the chosen display mode is not able to display all the available cameras.
Color: If this button is enabled, you can adjust the color of live images.
E-Zoom: Single channel large screen electronic amplification.
Audio: Enable sound.
PTZ: Click the PTZ button to control rotation position, speed and auto scan of the PTZ
connected to the IP camera.
Record: Click this button to start/stop recording.
Playback: Click this button to playback the recorded files.
You can click Move Tool button and drag it anywhere with the left mouse to move the main
menu bar anywhere.
Click Main Menu button to pop up a window as Fig 5-2; you can also press MENU button on
the front panel or operate with remote controller to display the main menu. Clicking Setup icon
will pop up the configuration menu:
Fig 5-2 Main Menu