PSC HD User manual

Models SR, HD, LR and XLR
Handheld Bar Code Scanner
User’s Guide

PSC Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
Telephone: [phone]
Telefax: [phone]
All rights reserved. No part of the contents of this documentation or
the procedures described therein may be reproduced or transmitted
in any form or by any means without prior written permission of PSC
Inc. Owners of PSC Inc.’s products are hereby granted non-exclusive,
revocable license to reproduce and transmit this documentation for
the purchaser’s own internal business purposes. Purchaser shall not
remove or alter any proprietary notices, including copyright notices,
contained on this documentation and shall ensure that all notices
appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire
printed versions by contacting PSC Customer Administration. Elec-
tronic versions will either be downloadable from the PSC web site
(www.pscnet.com) or provided on appropriate media. If you visit our
web site and would like to make comments or suggestions about this
or other PSC publications, please let us know via the “Contact PSC”
page.
Disclaimer
Reasonable measures have been taken to ensure that the
information included in this manual is complete and accurate.
However, PSC reserves the right to change any specification
at any time without prior notice.
PSC and the PSC logo are registered trademarks of PSC Inc. All
other trademarks and trade names referred to herein are property of
their respective owners.

User’s Guide 1
Table of Contents
Unpacking and Inspecting Your Scanner..................................... 3
Installation .................................................................................... 4
How to Scan................................................................................. 6
Scanning Range .................................................................... 7
Active Symbologies ............................................................. 11
Enhanced Scanning for Hard-to-Read Bar Codes .............. 11
Test Your Scanner ..................................................................... 12
Laser Cautions ........................................................................... 13
Radio Frequency Interference.................................................... 13
Troubleshooting ......................................................................... 14

2PowerScan™ Scanner
NOTES

User’s Guide 3
Unpacking and Inspecting Your Scanner
After unpacking your new scanner, check the contents of the ship-
ping carton to ensure all the items you ordered are included:
•PowerScan
™handheld scanner
•Interface Cable
•Power Supply (if you ordered one)
•User’s Guide (this manual)
•Programming Guide
•Optional Accessories that you ordered. (The PowerScan
handheld bar code scanner can be purchased with or without
accessory kits.)
If your package contains wrong or missing components, contact your
place of purchase. If there are damaged components, immediately file
a claim with the carrier. You may want to save your packing material
in case you need to ship the scanner at some later time.
NOTE
Manuals for the PowerScan scanner are available
on our website. See the back cover for our web
address.

4PowerScan™Scanner
Installation
Refer to Figure 1 and follow these steps to install the scanner:
Consult your host terminal manual to determine if power must be
turned off before connecting peripheral devices such as the scanner.
1. Should you need to disconnect the interface (I/F) cable from
the scanner, loosen the Phillips head screw at the bottom of
the handle and rotate the cable restraint clip away from the
cable to release it. Reverse this procedure to connect the
cable.
2. Connect the I/F cable to the proper port on the host terminal.
3. If your system requires an AC/DC adapter to power the
scanner, connect the adapter’s power cord at the I/F connec-
tor. (Note: In most cases, the scanner uses Power Off the Ter-
minal [P.O.T.], and does not require this step.) Contact your
PSC dealer if you’re not sure if an AC/DC adapter should be
used with your system.
4. Connect the AC/DC adapter at the wall outlet. (P.O.T. units
skip this step.)
5. Verify operation—point at a flat surface and pull the trigger.
A red beam should be visible. Scan a sample bar code and
confirm that the scanner reads the bar code by beeping and/
or sending the data to the host terminal.
Power Supply
The scanner requires either a Listed Class 2 or Listed LPS power
source which supplies power directly to the scanner.
CAUTION
Do not attempt to pull the End Cap off, as this may
damage the scanner.

User’s Guide 5
Figure 1. Installing the Scanner
1
4
3
5
2

6PowerScan™Scanner
How to Scan
Figure 2 illustrates some tips to help get the best scanning results:
1. The scanner must be pointed at a slight angle to the bar code.
Do not hold the scanner perpendicular to the bar code.
2. The laser beam must cross the entire bar code. The scanner
cannot correctly read if the entire bar code is not scanned.
Figure 2. Scanning Tips
2
2
1
1

User’s Guide 7
Scanning Range
There are currently four different model types for this scanner.
Depending upon the model type of your scanner, you’ll need to hold
the unit at a given distance from the bar code to achieve optimum
scanning results. The following diagrams provide range of field infor-
mation for each of the models when scanning grade A, Code 39 bar
codes: Standard Range (SR), High Density (HD), Long Range (LR)
and Extra Long Range (XLR).
Figure 3. Depth of Field (SR)
NOTE
In the context of the illustration below, a "mil" repre-
sents the minimum bar code element width. Mea-
surements are based on SR models set with the
standard 28°scan width (as opposed to the Half
Angle setting of 14°). Reference the PowerScan Pro-
gramming Manual (P/N R44-1840) for more informa-
tion about the Half Angle feature.
Specifications are subject to change without notice.
Depth of Field
Paper Labels (SR decoded model, Code 39)
0
20 mil
15 mil
10 mil
5 mil
CENTIMETERS
FEET
FRONT OF SCANNER
10
12345
20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
40 mil
7.5 mil
55 mil

8PowerScan™Scanner
Figure 4. Depth of Field (HD)
NOTE
In the context of the illustration below, a "mil" repre-
sents the minimum bar code element width. Mea-
surements are based on HD models set with the
standard 28°scan width (as opposed to the Half
Angle setting of 14°). Reference the PowerScan Pro-
gramming Manual (P/N R44-1840) for more informa-
tion about the Half Angle feature.
Specifications are subject to change without notice.
Depth of Field
Paper Labels (HD decoded model, Code 39)
7.5 mil
5 mil
4 mil
3 mil
INCHES
FRONT OF SCANNER
0
CENTIMETERS
5
1 234567 8
10 15 20
10 mil
20 mil

User’s Guide 9
Figure 5. Depth of Field (LR)
NOTE
In the context of the illustration below, a "mil" repre-
sents the minimum bar code element width. Mea-
surements are based on LR models set with the a
14°scan width (as opposed to the alternate Full
Angle setting of 28°). Reference the PowerScan Pro-
gramming Manual (P/N R44-1840) for more informa-
tion about the Half Angle feature.
Specifications are subject to change without notice.
Depth of Field
Paper Labels (LR decoded model, Code 39)
0
40 mil
20 mil
15 mil
7.5 mil
CENTIMETERS
FEET
FRONT OF SCANNER
10
12345
20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
6789
170 180 190 200 210 220 230 240 250 260 270 280
10 mil
55 mil
Reflective Labels (LR decoded model, Code 39)
70 mil
55 mil
40 mil
CENTIMETERS
FEET
FRONT OF SCANNER
6706506306105905705505305104904704504304103903703503303102902702502302101901701501301109070503010
1
0
2345678910 11 12 13 14 15 16 17 18 19 20 21 22
100 mil

10 PowerScan™Scanner
Figure 6. Depth of Field (XLR)
NOTE
In the context of the illustration below, a "mil" repre-
sents the minimum bar code element width. Mea-
surements are based on XLR models set with a 10°
scan angle width.
Specifications are subject to change without notice.
Depth of Field
Paper Labels (XLR decoded model, Code 39)
0
40 mil
20 mil
15 mil
CENTIMETERS
FEET
FRONT OF SCANNER
12345678910 11 12 13 14 15
45040035030025020015010050
55 mil
Reflective Labels (XLR decoded model, Code 39)
70 mil
40 mil
CENTIMETERS
FEET
FRONT OF SCANNER
11001050100095090085080075070065060055050045040035030025020015010050
1
0
2345678910 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
100 mil

User’s Guide 11
Active Symbologies
The active (enabled) bar code symbologies in the factory defaults are:
•Code 39 (C39)
•Code 128 (C128)
•Interleaved 2 of 5 (I 2 of 5)
Your scanner should be pre-programmed with these standard factory
default settings, unless...
...it was shipped to you programmed with unique, customer con-
figuration settings.
...you or another user have made changes to scanner program-
ming.
Enhanced Scanning for Hard-to-Read Bar Codes
Decoded scanners can be programmed to decode extremely poor
quality bar codes by activating advanced Quadralogic™Decoding.
To select this feature, see the PowerScan™Scanner Programming
Guide (P/N R44-1840) available from your dealer, or you can down-
load the manual from our website.
Scanner programming can also be performed using your PC and the
Configurator Express™On-Screen Programming tool also available
from your dealer.

12 PowerScan™Scanner
Test Your Scanner
The bar code below (Figure 7) is provided to test your scanner’s abil-
ity to read a typical Code 39 label.
Figure 7. Code 39 Bar Code Sample
Figure 8. Scanner Labeling
NOTE
Figure 8 above shows label placement ONLY. For
actual regulatory, patent and other applicable infor-
mation, view the labels on the product itself, or call
your nearest sales or service representative.
Tes t
CLASS No.
SERIAL No.
MFG. DATE:
LASER RADIATION-DO NOT STARE INTO BEAM
1mw - 650-685nm CLASS 2 LASER PRODUCT
Based on 100 sec., EN60825-1/A11:1996
ACN
073200496
CUS
LISTED
NWGQ 2Z78
®
A
V
O
I
D
E
X
P
O
S
U
R
E
—
L
A
S
E
R
R
A
D
I
A
T
I
O
N
I
S
E
M
I
T
T
E
D
F
R
O
M
T
H
I
S
D
E
V
I
C
E
.
Complies with 21CFR 1040
and part 15 of FCC Rules.
Applicable patents are listed
on label inside unit.
CAUTION—LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.
COVERED
BY ONE OR MORE OF THE
FOLLOWING PATENTS:
4,387,297 •4,409,470 •4,460,120
4,593,186 •4,652,750 •4,673,805
4,736,095 •4,816,660 •4,845,350
4,861,972 •4,866,257 •4,879,456
5,179,270 •5,180,904 •5,237,161
5,247,161 •5,247,162 •5,258,604
5,260,554 •5,298,728 •5,311,000
5,330,370 •5,468,949 •5,475,206
5,481,098
Other patents pending

User’s Guide 13
Laser Cautions
The PowerScan bar code scanner is certified in the U.S. to conform to
the requirements of DHHS/CDRH 21CFR Subchapter J for Class II laser
products. Class II products are not considered to be hazardous. The
scanner contains a Visible Laser Diode (VLD) at a wavelength of 650-
670 nanometers and is designed so that there can be no human access
to harmful levels of laser light during normal operation, user mainte-
nance, or during prescribed service operations.
Radio Frequency Interference
This device complies with Part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe B respecte toutes les exigences du
Reglement sur le material broilleur du Canada.
CAUTION
If the scan pattern is a single dot when depressing
the trigger, discontinue operation and return the
unit to the factory. Exception: When using Marker
Beam Mode a single aiming dot is projected
momentarily.
CAUTION
Do not attempt to open or otherwise service any
components in the optics cavity. Opening or servic-
ing any part of the optics cavity by unauthorized
personnel may violate laser safety regulations.

14 PowerScan™Scanner
Troubleshooting
You can isolate problems with your scanning system by performing
these checks (refer to Figure 9):
1. If your scanner’s cable is designed to receive Power Off the
Terminal (P.O.T.), it will not operate unless it is connected to a
working host terminal that is powered on.
2. Ensure that the interface cable is securely attached to the
host. Consult your technical support manager or refer to
your host system manual to identify the proper connection
for the scanner.
3. If an external power supply is used, verify that it is securely
connected to the interface cable and AC outlet. Also ensure
that the power supply is the correct voltage rating for your
area.
4. Check to see that the interface cable is securely connected at
the scanner handle. Push the connector in to assure that it is
firmly seated. Use a Phillips head screwdriver to ensure that
the screw at the bottom of the scanner is fully tightened (but
do not overtighten).
5. If, after checking all connections, the scanner still fails to
function properly, exchange the power supply with a known
good power supply.
6. Ensure that the scanner's interface type is compatible with
the host terminal by consulting your POS system manual
and/or the PowerScan Scanner Programming Guide
(P/N R44-1840).
7. Verify that the bar codes you are scanning are of satisfactory
quality. Bar code label verifiers are available from your
dealer if you need precise reporting of bar code details. Bar
codes that are damaged (wrinkled, smudged, or torn) may
cause the scanner to read poorly or not at all. If bar code
quality seems to be the problem, check to see if the scanner
will read a known good bar code (see Figure 7). You may also
want to modify the programmable setting for advanced
Quadralogic™decoding (see the section in this manual
titled, Enhanced Scanning for Hard-to-Read Bar Codes).

User’s Guide 15
Figure 9. Troubleshooting the Scanner
OFF
ON
OFF
ON
1
2
3
5
7
Programming
Kit
5
99 531 75790
4
6

16 PowerScan™Scanner
NOTES

DECLARATION OF CONFORMITY
PSC hereby declares that the Equipment specified below has
been tested and found compliant to the following Directives
and Standards:
Charles W. Vanlue
Director, Corporate Quality
PSC, Inc.
959 Terry Street
Eugene, OR 97402
U.S.A.
Nigel Davis
Vice President
Europe, Middle East & Africa
PSC Bar Code Ltd.
Axis 3, Rhodes Way
Watford, England
WD24YW
UK
Directives: EMC 89/336/EEC
Low Voltage 73/23/EEC
Standards: EN55022-B EN60825
EN50082-1 EN60950
Equipment
Type: Bar Code Scanning Equipment
Product: PowerScan™Bar Code Scanner
PowerScan™LR Bar Code Scanner
PowerScan™XLR Bar Code Scanner

Asia Pacific
PSC Hong Kong
Hong Kong
Telephone: [852]-2-584-6210
Fax: [852]-2-521-0291
Australia
PSC Asia Pacific Pty Ltd.
North Ryde, Australia
Telephone: [61] 0 (2) 9878 8999
Fax: [61] 0 (2) 9878 8688
France
PSC Sarl
LES ULIS Cedex, France
Telephone: [33].01.64.86.71.00
Fax: [33].01.64 46.72.44
Germany
PSC GmbH
Darmstadt, Germany
Telephone: + 49 (0) 61 51/93 58-0
Fax: + 49 (0) 61 51/93 58 58
Italy
PSC S.r.l.
Vimercate (MI), Italy
Telephone: [39] (0) 39/62903.1
Fax: [39] (0) 39/685496
Japan
PSC Japan K.K.
Shinagawa-ku, Tokyo, Japan
Telephone: [phone]
Fax: [phone]
Latin America
PSC S.A., INC.
Miami, Florida, USA
Telephone: [phone]
Fax: [phone]
United Kingdom
PSC Bar Code Ltd.
Watford, England
Telephone: [phone]
Fax: [phone]
Corporate Headquarters
675 Basket Road
Webster, NY 14580-9787
Telephone: [phone]
Fax: [phone]
PSC Scanning, Inc.
959 Terry Street
Eugene, OR 97402-9150
Telephone: [phone]
Fax: [phone]
Printed on recycled paper
PRINTED WITH
SOY INK
www.pscnet.com
© 2000 PSC INC. R44-2094 (Rev. B) Printed in USA (11/00)