PSM LD161 User manual

LD160 REV.E1-1
PSM LD16x vehicle loop detector installation guide
1. Pin connections
MODEL NO.
PIN
161
162
163
1
110 VAC, LINE
230 VAV, LINE
12~24 VADC
LD-161
1
110 VAC, NEUTRAL
230 VAC, NEUTRAL
12~24 VADC
3
Output B Relay (N.O.)
Output B Relay (N.O.)
4
Chassis Ground
Output B Relay (COM.)
5
Output A Relay (COM.)
Output A Relay (COM.)
6
Output A Relay (N.O.)
Output A Relay (N.O.)
7
Loop
Loop
LD-162
8
Loop
Loop
LD-163
9
Output B Relay (COM.)
Chassis Ground
10
Output A Relay (N.C.)
Output A Relay (N.C.)
11
Output B Relay (N.C.)
Output B Relay (N.C.)
2. Front panel LED and switch
(1) POWER：POWER RED LED→On= Power applied to detector.；Off = No power or fuse is
bad.
(2) DETECT：DETECT GREEN LED→On = Vehicle being detected；Blinking = Loop Failure.
(3) SWITCH 1(SENSITIVITY)：Selections of sensitivity are from 0 to 9 and A to F where 0
stands for the lowest sensitive and F is the highest sensitive.
Unit：-ΔL/L × 100﹪
SENSITIVITY LEVELS
LEVEL 0
2.56
LEVEL 4
0.48
LEVEL 8
0.12
LEVEL C
0.030
LEVEL 1
1.28
LEVEL 5
0.32
LEVEL 9
0.08
LEVEL D
0.020
LEVEL 2
0.96
LEVEL 6
0.24
LEVELA
0.06
LEVEL E
0.015
LEVEL 3
0.64
LEVEL 7
0.16
LEVEL B
0.04
LEVEL F
0.010
(4) SWITCH 2(DIP SWITCH)：
1. DIP 1 & DIP 2 FUNCTION：
DIP NO.
DIP MODE
FUNCTION
DIP 1
□■ON
2 seconds delay for the relay. It will be no output for a vehicle with a speed
that is faster than 8 Km/Hr.
DIP 2
□■ON
Increase detector’s sensitivity to avoid the failed detection. Especially in the
case of trailer or trucks.
2. DIP 3 & DIP 4 －OUTPUT B MODE：
DIP NO.
DIP 3
DIP 4
OUTPUT B MODE
DETECT
DIP MODE
OFF■□
OFF■□
Pulse on entry
Output B mode
□■ON
OFF■□
Pulse on exit
Output B mode
OFF■□
□■ON
Presence mode
Output B mode
□■ON
□■ON
Output B will set to the presence mode when the loop failed.
3. DIP 5 FUNCTION：
DIP NO.
DIP 5
PRESENCE MODE
DIP MODE
□■ON
Continuous detect output is maintained as long as the vehicle remains on
the loop.
OFF■□
Hold time of 5 minutes for any vehicle detected.

LD160 REV.E1-2
4. DIP 6 & DIP 7 & DIP 8 －CONTROLS OUTPUT A EXTEND TIME：
DIP NO.
DIP 6
DIP 7
DIP 8
EXTEND
DETECT
DIP MODE
OFF■□
OFF■□
OFF■□
No extend
Output A
□■ON
OFF■□
OFF■□
2 seconds
Output A
OFF■□
□■ON
OFF■□
5 seconds
Output A
□■ON
□■ON
OFF■□
8 seconds
Output A
OFF■□
OFF■□
□■ON
10 seconds
Output A
□■ON
OFF■□
□■ON
15 seconds
Output A
OFF■□
□■ON
□■ON
20 seconds
Output A
□■ON
□■ON
□■ON
30 seconds
Output A
5. DIP9 & DIP10 －FREQUENCY SELECTION(40K to 80KHz)：
DIP NO.
DIP 9
DIP 10
FREQUENCCY RANG
DIP MODE
OFF■□
OFF■□
High frequency
□■ON
OFF■□
Medium-High frequency.
OFF■□
□■ON
Medium frequency.
□■ON
□■ON
Low frequency.
＊When more than two loops are used, please set up different frequencies in order to eliminate the crosstalk.
(4) RESET Button
RESET button can reset the detector. RESET is needed whenever a frequency is changed.
3. Installation Information
(1) Teflon loop is recommended and the maximum length could reach
500 meter.
(2) Loops should have 3 to 5 rotaries; the remains of the cable need
to have a helix every 15 cm.
(3) Typical saw cut loop installation：
(4) The more rotaries of a loop, the lower of the frequency.
(5) The appropriate way of the rotation of a loop is 1.0 to 2.0M in
length and 0.8 to 1.2M in width.
(6) The loop should be installed in an area where has no electric
overhead door near by.
(7) Any vehicle with a speed of no more than 120Km/Hr will be
detected.
(8) The specification for both outputs is 110VAC/10A.
(9) Appropriate way to correct a failed detector:
Press “RESET” button.
Check the DETECT and POWER LED：
If POWER RED LED is dark, check AC power source and fuse (0.5A, inside of the detector).
If DETECT GREEN LED is blinking, the loop may have a short circuit.
If DETECT GREEN LED is blinking very slowly, loop does not have enough rotaries.
If DETECT GREEN LED is blinking very rapidly, loop has too many rotaries.
When loop has not enough rotaries (frequency will also be too high), change DIP switch to low frequency.
When loop has too many rotaries (frequency will also be too low), increase the loop rotaries.
PERIMETER (M)
NO. OF TURNS
3 ~ 4 M
6
4 ~ 6 M
5
6 ~ 10 M
4
10 ~ 20 M
3
20M ~ UP
2