Visonic SPY 1 User manual

DE1151 SPY 1, 2, 3, 4 Installation Instructions 1
SPY 1, 2, 3, 4
SPY 1, 2, 3, 4SPY 1, 2, 3, 4
SPY 1, 2, 3, 4
Miniature PIR Detectors
Installation Instructions
1. INTRODUCTION
1. INTRODUCTION1. INTRODUCTION
1. INTRODUCTION
•Ultra-miniature
•Reliable
•Trouble free
•Four different models for different applications.
•Virtually unnoticeable when installed
•Fast, easy installation
•In-ceiling or in-wall installation
•Special anti-false alarm features:
−
−−
−2-step built-in pulse counter
−
−−
−Light rejection filter to reject visible light variations
−
−−
−Dual-element low-noise pyroelectric detector
•RF immunity up to 1000 MHz
•N/C silent relay output
•Low 12.5 mA current drain @ 12 VDC
•10-14 VDC supply voltage
The new SPY series features the smallest passive infrared (PlR)
detectors of their type presently marketed. Models are designed
for in-wall or in-ceiling installation, or behind the wall (or ceiling)
mounting. The only visible part of the SPY after installation is the
ultra miniaturized lens itself.
False alarms caused by environmental disturbances are virtually
eliminated by a combination of light rejection filter and pyro-
electric low-noise detector. The medium angle, wide angle and
curtain SPYs have the additional protection of built-in two-step
pulse counting. With careful attention to installation site and
periodic walk-testing, Visonic Ltd. SPY PlR detectors will give
reliable, long-life, trouble-free service.
Models available:
SPY 1: Long Range. Provides narrow angle corridor pattern with
maximum coverage area of 11 m/17°(35 ft/17°).
SPY 2: Medium Angle. Provides 3 double beams in a single
detection layer with maximum coverage area of 8 m/50°
(25 ft/50°)
SPY 3: Wide Angle. Provides 6 double beams in a single
detection layer with maximum coverage area of 8 m/100°
(25 ft/100°).
SPY 4: Curtain. Provides a solid curtain with maximum coverage
pattern of 2 m width x 4 m height (6 x 12 ft).
SPY RTE-A: Special request-to-exit model, relay output.
SPY RTE-B: Request-to-exit model, open collector output.
SPY 1 - Long Range SPY 2 - Medium Angle SPY 3 - Wide Angle SPY 4 - Ceiling Mounted Curtain
SPY 4 - Wall Mounted Curtain
Note: These units are not designed for pet alley use.
2. SPECIFICATIONS
2. SPECIFICATIONS2. SPECIFICATIONS
2. SPECIFICATIONS
OPTICAL - Detection Patterns
SPY 1 Long Range; narrow angle corridor pattern. Coverage
Area: max. 11 m/17°(35 ft/17°)
SPY 2 Medium Angle; 3 double beams in a single detection
layer. Coverage Area: max. 8 m/50°(25 ft/50°)
SPY 3 Wide Angle; 6 double beams in a single detection
layer. Coverage Area: max. 8 m/100°(25 ft/100°)
SPY 4 Curtain; solid curtain pattern. Coverage pattern: max.
2 m wide x 4 m high (6 x 12 ft)
ELECTRICAL
Voltage: 10 - 14 VDC
Current: 12.5 mA @ 12 VDC
Alarm Output
SPY 1, 2, 3, 4 and SPY RTE-A: Normally closed (fail-safe)
contacts. Rating: 0.1 A resistive / 30 VDC. 18-ohm resistor in
series with contacts.
SPY RTE-B: Open collector output, 50 mA maximum
Alarm Period
SPY 1, 2, 3, 4: 2-10 seconds
SPY RTE-A and B: 1-2 seconds
Detector: Dual-element, low-noise pyroelectric detector
Pulse Counter
SPY 2, 3 and 4: Factory set to 2 pulses alternate polarity
SPY-1 and SPY RTE-A and B: 1 pulse

2 DE1151 SPY 1, 2, 3, 4 Installation Instructions
INSTALLATION
Suitable for wall or ceiling installation, and available with both a
collar and a front or rear mounting plate, depending on the model.
ENVIRONMENTAL
Operating Temperature: 0°C to 50°C (32°F to 122°F)
Storage Temperature: -20°C to 60°C (-4°F to 140°F)
RFl Protection: Greater than 10 V/m to 1000MHz
PHYSICAL
Dimensions: Diameter: 19 mm (0.75 in) Length: 70 mm (2.75 in)
Weight: 30 g (1.1 oz)
Color: White
3. INSTALLATION
3. INSTALLATION3. INSTALLATION
3. INSTALLATION
ATTENTION: Whichever model of SPY PIR detector you are
installing, please observe the following:
1. Never touch the lens. Whenever you are handling the
detector, hold it firmly by the collar, mounting plate, or sides.
2. Splice or solder the wires from the control panel to the SPY
detector. Do not attach by only twisting wires together.
3. Insulate each wire individually. Do not permit uninsulated
wires to touch each other.
4. During the wiring operation, be careful to place the detector
so that the lens is protected.
5. Do not open the detector from either the front (lens end) or
the back (wire end).
FAILURE TO OBSERVE THESE PROCEDURES MAY
INVALIDATE YOUR WARRANTY.
3.1 Choosing the Right Loc tion
SPY PIRs can be installed in a wall or ceiling and are available
with both a collar and a front/rear mounting plate. Three of the
models (SPY 1, 2 and 4) can be installed with the mounting plate
in the front or rear of the detector unit, as required. The choice of
method depends upon the type of wall or ceiling and the degree
to which the detector should be unnoticed.
•SPY Models SPY 1, SPY 2 and SPY 4 are provided with both
a collar and a front/rear mounting plate.
•SPY 3 is provided with a fixed mounting plate for front- of-the-
wall installation.
1. Select the mounting location so that the expected motion of
an intruder will cross the coverage pattern.
2. When wall mounted, the SPY should be installed parallel to
the floor for maximum coverage. Recommended mounting
height: between 80 cm and 1.35 m (2.5 and 4.5 ft).
3. The curtain detector SPY 4 can be mounted in the ceiling or in
the wall. When mounting in the wall it should be installed
parallel to the floor. Maximum ceiling height: 4 m (12 ft).
4. Always install the unit into a firm and stable surface, and
assure that there are no moving objects within its field of view.
Remember: Passive infrared detectors are sensitive to
changes in infrared energy caused by an object moving
across the unit's field of view. Detection depends on the
difference between the amount of infrared energy
transmitted by the moving object and the temperature of the
background.
It is therefore recommended that the detector be aimed toward
the coolest place in the area to be protected, in order to obtain
maximum sensitivity in installations where high ambient tempera-
tures are expected. Do not aim the detector toward areas
containing hot water pipes or windows, which might cause
problems in the operational efficiency of PIR detectors.
BEFORE YOU START:
Do not touch the lens.
Solder or splice wire connections.
Insulate wires individually so that they cannot touch.
3.2 Inst ll tion with Coll r
(MODELS SPY 1 and 2)
1. Drill a 22 mm (7/8 in.) hole in the wall.
2. Hold the detector unit by the sides. Carefully put the collar on
the detector and adjust its
position so that the front of
the detector and the collar
are aligned (Fig. 1).
3. Fish the wiring from the
control panel through the
hole and connect to the
detector unit as described
under WIRING.
4. Feed the wiring into the
prepared hole.
5. Orient the detector unit so
Figure 1 - Installation with
Collar, Models SPY 1, SPY 2
that the mark on the front faces up (Fig. 1).
6. With your fingers on the outer edge of the collar, push the
detector unit, rear end first, into the hole until the retaining
collar is seated securely.
3.3 Front-of-W ll Inst ll tion
(MODELS SPY 1 and 2)
1. Drill a 24 mm (15/16 in) hole in the wall.
2. Hold the detector unit by the sides and put it, lens end first,
into the mounting plate (Fig. 2A).
3. Adjust the detector unit in the mounting plate so that the front
of the detector extends a minimum distance from the wall.
4. Place the locking ring over the rear end of the detector unit
and move it over the tabs of the locking plate until the detector
unit is absolutely stable in the mounting plate (Fig. 2A).
5. Fish the wiring from the control panel through the hole and
connect to the detector unit as described in WIRING.
6. Feed the wiring into the prepared hole.
7. Prepare the mounting plate screw holes on a horizontal line,
making sure that the mark on the front of the detector unit is
facing up (Fig. 2B).
8. Insert the detector unit, rear end first, into the hole with the
mark on the front facing up (Fig. 2B) and secure the mounting
plate to the wall with the screws provided.
Figure 2 (A & B) - Front of Wall Installation, Models SPY 1 and 2
3.4 B ck-of-W ll Inst ll tion
(Models SPY 007.1, 007.2)
1. Drill a 19 mm (3/4 in.) hole in the wall.
2. Hold the detector unit by the sides and put it, lens end first,
into the mounting plate (Fig. 3A).
3. Adjust the detector unit in the mounting plate according to the
thickness of the wall. When installed, the lens end of the
detector should extend about 1 mm (0.05 in.) from the wall.

DE1151 SPY 1, 2, 3, 4 Installation Instructions 3
4. Place the locking ring over the rear end of the detector unit
and move it over the tabs of the locking plate until the detector
unit is absolutely stable in the mounting plate (Fig. 3A).
5. Connect the detector unit and control panel wires as
described in WIRING.
6. Prepare the mounting plate screw holes on a horizontal line,
making sure that the mark on the front of the detector unit
faces up (Fig. 3B).
7. Insert the detector unit, front end first, into the hole with the
mark on the front facing up (Fig. 3B) and secure the mounting
plate to the back of the wall with the screws provided.
Figure 3 (A & B) - Back of Wall Installation, Models SPY 1 and 2
3.5 Inst ll tion of Model SPY 3
1. Drill a 3/4 in. (19 mm) hole in the wall.
2. Fish the wiring from the control panel through the hole and
connect them to the detector unit as described in WIRING.
3. Feed the wiring into the prepared hole.
4. Prepare the mounting plate screw holes on a horizontal line,
making sure that the mark on the front of the detector unit
faces up (Fig. 4).
Figure 4. Model SPY 3 Installation
5. Holding the detector unit by the mounting plate, insert it, rear
end first, into the hole, with the mark on the front facing up
(Fig. 4).
6. Secure the mounting plate to the wall with the screws
provided.
3.6 Ceiling Inst ll tion of Curt in
Model SPY 4
Refer to the ceiling-mounted coverage pattern of SPY 4.
Installation with Collar: Select a location so the curtain pattern
lies across the anticipated direction of motion (Fig. 5A).
1. Refer to Installation with Collar, Models SPY 1 and 2.
2. Replace Step 6 with the following:
Step 5 - Orient the detector unit so that the mark on the unit is
perpendicular to the direction of motion (Fig. 5A).
Installation with Mounting Plate: Select a location that will
place the curtain pattern in the direction of motion (Fig. 5B).
1. Refer to Back of Wall Installation,
2. Replace Step 6 with the following:
Step 6 - Prepare the mounting plate screw holes so they are
in line with the anticipated direction of motion (Fig. 5B).
Step 7 - Install the detector unit, front end first, into the hole
with the mark on the front perpendicular to the path of
travel (Fig. 5B) and secure the mounting plate to the back of
the ceiling with the screws provided.
Figure 5A - Model SPY 4
Installation with Collar
Figure 5B - Model SPY 4
Installation with Mounting Plate
3.7 In-W ll Inst ll tion of Curt in
Model SPY 4
Refer to curtain wall mounted coverage pattern of Model SPY 4.
1. Follow the appropriate instructions above for installation with
collar or mounting plate.
2. Install the detector unit perpendicular to the floor. Recom-
mended mounting height: between 80 cm and 1.35 m (2.5 and
4.5 ft).
3. Position the detector unit with the mark on the front facing up.
3.8 Wiring
Caution: Do not apply power until all connections are made.
A. SPY 1 through 4
Red to +12 VDC White Common (dry contact)
Black to −12 VDC Green Normally Closed (dry contact)
1. Connect wires by splicing or soldering. Avoid any possible
contact between the connected wires by insulating them
separately.
2. Use #22 AWG wire or larger.
3. Connect the 12 VDC (+) and (−) wires to a 10 to 14 Volt DC
power source and check for correct polarity. The power
source should have a back-up battery capable of supplying
power for at least four hours of operation during power failure.
Current drain of each sensor is approximately 12.5 mA @ 12
Volts DC.
4. Connection of relay to control panel: Connect the White and
Green wires to a normally closed burglary protection zone of
the control panel.
Relay contacts will open when motion is detected or during
power loss. The relay contacts are rated at 100 mA, 30 VDC
maximum (resistive load only). An 18 ohm resistor is internally
connected in series with the relay contacts.
2nd. SPY RTE-A and B
Wire the SPY RTE models as shown in Figure 6.
Figure 6. SPY RTE Wiring

4 DE1151 SPY 1, 2, 3, 4 Installation Instructions
3.9 W lk Testing
Apply 12 VDC power and allow 5 minutes for the unit to warm up
and stabilize before testing.
Walk-Test the coverage area by walking slowly across the field of
view, first one way and then the other, while monitoring the N/C
relay contacts with an ohmmeter. Alternatively, place the control
panel in the test mode (if possible). The relay contacts will open
whenever you walk across the PIR detection pattern. This will be
indicated either on the ohmmeter or by whatever signal is
designated through the control panel. Allow 10 seconds between
each test for the unit to stabilize.
NOTE: The range and coverage area should be
checked at least once a year.
To assure proper continuous functioning, the user should be
instructed to perform a walk test at the far end of the
coverage pattern to assure an alarm signal prior to each time
the alarm system is armed.
WARRANTY
WARRANTYWARRANTY
WARRANTY
Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original
purchaser only (the “Purchaser”) against defective workmanship and materials under normal use of
the Product for a period of twelve (12) months from the date of shipment by the Manufacturer.
This Warranty is absolutely conditional upon the Product having been properly installed, maintained
and operated under conditions of normal use in accordance with the Manufacturers recommended
installation and operation instructions. Products which have become defective for any other reason,
according to the Manufacturers discretion, such as improper installation, failure to follow
recommended installation and operational instructions, neglect, willful damage, misuse or vandalism,
accidental damage, alteration or tampering, or repair by anyone other than the manufacturer, are not
covered by this Warranty.
The Manufacturer does not represent that this Product may not be compromised and/or
circumvented or that the Product will prevent any death and/or personal injury and/or damage to
property resulting from burglary, robbery, fire or otherwise, or that the Product will in all cases
provide adequate warning or protection. The Product, properly installed and maintained, only
reduces the risk of such events without warning and it is not a guarantee or insurance that such
events will not occur.
THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO
ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS
WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER, AS AFORESAID.
THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTAL, CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR
EXPENSE, INCLUDING LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR
INDIRECTLY ARISING FROM PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR
FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN
IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR
BODILY INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT,
INDIRECT, INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE
PRODUCT FAILED TO FUNCTION.
However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage
arising under this limited warranty, the Manufacturer's maximum liability (if any) shall not in any case
exceed the purchase price of the Product, which shall be fixed as liquidated damages and not as a
penalty, and shall be the complete and exclusive remedy against the Manufacturer.
When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and
warranty and he recognizes having been informed of.
Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so
these limitations may not apply under certain circumstances.
The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or
malfunctioning of any telecommunication or electronic equipment or any programs.
The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the
Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or
replacement shall not extend the original Warranty period. The Manufacturer shall not be
responsible for dismantling and/or reinstallation costs. To exercise this Warranty the Product must
be returned to the Manufacturer freight pre-paid and insured. All freight and insurance costs are the
responsibility of the Purchaser and are not included in this Warranty.
This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize
any person to act on its behalf in the modification, variation or extension of this warranty. This
warranty shall apply to the Product only. All products, accessories or attachments of others used in
conjunction with the Product, including batteries, shall be covered solely by their own warranty, if
any. The Manufacturer shall not be liable for any damage or loss whatsoever, whether directly,
indirectly, incidentally, consequentially or otherwise, caused by the malfunction of the Product due to
products, accessories, or attachments of others, including batteries, used in conjunction with the
Products. This Warranty is exclusive to the original Purchaser and is not assignable.
This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty
which is contrary to the Law in the state or country were the Product is supplied shall not apply.
Warning:The user must follow the Manufacturer’s installation and operational instructions including
testing the Product and its whole system at least once a week and to take all necessary precautions
for his/her safety and the protection of his/her property.
1/08
W.E.E.E. Product Recycling Declaration
For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not
returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.
Directive 2002/96/EC Waste Electrical and Electronic Equipment.
EMAIL: [email protected]
INTERNET: www.visonic.com
VISONIC LTD. 2014 SPY 1, 2, 3, 4 DE1151- (REV. 4 , 1/14)