Pulsar PSU-B-13,8V/S-3,5A/1/EL-TR-17Ah/MC User manual

PSU-B-13,8V/S-3,5A/1/EL-TR-17Ah/MC
PSBC 3512
v.1.2
Buffer, sw tch ng power supply un t
EN
Edition: 3 from the 24
th
June 2010
Supercedes edition: 2 from the 16
th
December 2008

2
Features of the power supply un t:
• 13.8 VD uninterruptible power supply
• ontrolling of the battery charging and
maintaining
• Protecting the battery against excessive
discharging (UVP)
• BAT output is full protected against short-
circuit and reverse connection
• Selectable battery charging current
• START function of manual battery actuation
• AUX output fuse check
• LED optical signalisation
• BS outlet for the signalling of the 230V
network collapse
• AW output of power supply unit failure, tripped
by:
• short-circuit (S P)
• overload (OLP)
• failure of D /D voltage converter
• Safety equipment:
• S P short-circuit protection
• OLP overload protection
• OHP overheat protection
• Overvoltage protection
• Against sabotage
CONTENTS:
1. Techn cal descr pt on.
1.1. General descr pt on
1.2. Block d agram
1.3. Descr pt on of elements and power supply connectors
1.4. Techn cal parameters
2. Installat on.
2.1. Requ rements
2.2. Installat on procedure
3. Mon tor ng of the power supply operat on.
3.1. Opt cal s gnal ng
3.2. Techn cal output
4. Serv ce and operat on.
4.1. Overloads or short c rcu ts to the PSU
4.2. Battery ass sted operat on.
4.3 Ma ntenance
1. Techn cal descr pt on.
1.1. General descr pt on.
The buffer power-supply is used for uninterrupted supply of alarm systems devices requiring stabilized
voltage of 12V/DC (+/-15%). The power-supply provides voltage within the following range: U= 11.0 V÷ 13.8 V DC
of total current efficiency equal to Imax=3.5A. In case of power voltage decay, prompt switching to battery supply
occurs.
The power-supply has got a metal casing (RAL 9003 color) with a space for 17Ah/12V battery. The casing
features a microswitch indicating door (front) opening.
Informat on about add t onal equ pment for PSBC 3512 power-supply (opt ons of max mal conf gurat on):
- 1 x LB5/AW fuse block (AWZ 536) + 17Ah
- 3 x converter D /D 2.5A/5V (AD 255) + 7Ah
- 2 x D /D 2.5A/5V (AD 255) + 1x voltage reducer RN-2.5A/12V (RN250) + 7Ah
- 1 x D /D 2.5A/5V (AD 255) + 1x RN-2.5A/12V (RN250) + LB5/AW (AWZ 536) + 7Ah
- 2 x LB5/AW (AWZ 536) + 1x RN-2.5A/12V (RN250) + 7Ah

3
1.2. Block d agram (f g.1).
Fig.1. Block diagram of the power-supply unit.

4
1.3. Descr pt on of elements and connect on l nks of the power-supply un t (tab.1, tab.2, f g.2).
Table 1.
Element no.
[F g. 2] Descr pt on
[1] F1 fuse in the battery circuit
[2] START pushbutton (power activation without A supply)
[3]
JP-B, jumper - configuration of UVP battery protection function
• JP-B= protection function (disconnection) of the battery off
• JP-B= protection function (disconnection) of the battery on
(disconnection U<10V)
Legend:
jumper installed jumper removed
[4] P1 potentiometer, voltage adjustment
[5] AC, LB, AUX optical indication of the power-supply unit operation
[6] OUTPUTS connector (Tab.2)
[7] AC, AUX onnection link of the output of the additional optical indication
[8] TAMPER, contact of antisabotage protection (NC)
[9] F2 witch in the Power supply circuit (230V/A )
[10] L-N
power-supply connector 230V/A , PE protection connector
[11] BAT+/BAT-: outputs, battery connectors +BAT=red, - BAT=blacks
[12]
J1, jumper – battery charging current selection
• J1= I
BAT
= 0,25 A
• J1= I
BAT
= 0,70 A
Legend:
jumper installed jumper removed
Tab.1. The elements of the power-supply unit.
Table 2.
[6] Descr pt on of power-supply un t outputs
~AC~ A supply input (18 V÷ 22 V A )
+BAT
-BAT
D supply output of the battery
(+BAT= red, -BAT=black)
+AUX
-AUX
D supply output
(+AUX= +U, -AUX=GND)
BS
A absence technical output –O type
level hi-Z = state: A power supply
level L = state: A power supply failure
AW
technical output of power supply operation status –O type
level L = state: correct operation
level hi-Z = state: failure, overload
Tab.2. Output terminals of the power-supply unit.

5
Fig.2. The view of the power-supply.

6
1.4. Techn cal parameters:
- electrical parameters (tab.3)
- mechanical parameters (tab.4)
- operation safety (tab.5)
- operation parameters (tab.6)
E lectr cal parameters (tab. 3).
Supply voltage 230V/A (-15%/+10%)
Supply frequency 50Hz
PSU power P 49 W
urrent consumption from the transformer 0.39 A (5.0 A „cold boot”)
Output voltage 11.0 V÷ 13.8 V D – buffer operation
10.0 V÷ 13.8 V D – battery assisted operation
Output voltage setting, escalation and
keeping time
20ms/50ms/10ms@Inom., Uac
Voltage setting range 11.5 V÷15.0 V
Voltage adjustment range ± 1%
Ripple voltage 60 mV p-p max.
Output current 3.5 A max.
urrent consumption by PSU systems 17 mA – battery assisted operation
Battery charging current 250mA / 700mA (± 5%) – jumper J1 selectable
Short-circuit protection S P
200% ÷ 250% of supply power – limitation of current and/or
fuse failure in the battery circuit (fuse-element replacement
required)
Overload protection OLP
110% ÷ 150% (@25º ÷55º ) of power supply – current
limitation with the PT automatic fuse, manual restart (the
fault requires the disconnection of the D output circuit)
Protection of the battery circuit S P 5A- current limitation, F1 fuse (failure requires replace of the
fuse-element)
Surge protection U>22V varistor
Excessive discharge protection UVP U<10,0 V (± 5%) – disconnection of (-BAT) battery
Technical outputs:
- BS output indicating failure of A power
supply
- AW technical output indicating operation
status of the power supply
- TAMPER output indicating opening of the
power-supply casing
- O type, 50mA max. normal status: level hi-Z, failure:
level L (0V), 20s time lag.
- O type, 50mA max. normal status: level L (0V),
failure: level H (hiZ), (automatically recovered after returning
correct operation)
- microswitch, N contacts (close casing),
0,5A@50V D (max.)
F1 fuse
F2 fuse
F 5A /250V
T 630 mA/ 250V
Mechan cal parameters (tab.4).
asing dimensions 235 x 305 x 98 (WxHxD) [mm] (+/- 2)
Fixation 205 x 275 x Φ 6 x4pcs (WxH)
Battery space 17Ah/12V (SLA) max.
Net/gross weight 2,90/3,10 kg
asing color RAL 9003
losing heese screw x 1 (at the front)
onnectors Power-supply: Φ0,63-2,50 (AWG 22-10)
Outputs : Ф0,41÷1,63 (AWG 26-14)
BAT battery outputs: 6,3F-2,5, 30cm
TAMPER output: wires, 30cm
Notes The casing is distant from the assembly surface so that cables can be installed

7
Operat on safety (tab.5).
Protection class PN-EN 60950-1:2004 I (first)
Protection grade PN-EN 60529: 2002 (U) IP20
Electrical strength of insulation:
- between input (network) circuit and output circuits of power-supply (I/P-
O/P)
- between input circuit and PE protection circuit (I/P-FG)
- between output circuit and PE protection circuit (O/P-FG)
3000 V/A min.
1500 V/A min.
500 V/A min.
Insulation resistance:
- between input circuit and output or protection circuit 100 MΩ, 500V/D
Operat on parameters (tab. 6).
Operation temperature -10º ...+40º
Storage temperature +5º ...+40º
Relative humidity 30%...90%, without condensation
Vibrations during operation
Unacceptable
Impulse waves during operation
Unacceptable
Direct isolation
Unacceptable
Vibrations and impulse waves during transport According to PN-83/T-42106
2. Installat on.
2.1 Requ rements.
The buffer power-supply shall be mounted by the qualified installer having appropriate (required and
necessary for a given country) permissions and qualifications for connecting (operating) 230V/A installations and
low-voltage installations. The device shall be mounted in closed rooms, according to the environment class II, of
the normal air humidity (RH=90% max. without condensation) and the temperature within the range from -10° to
+40° . The power-supply shall operate in a vertical position so that free and convectional air flow through
ventilating holes of the casing is guaranteed.
Before installation is started, the balance of the power-supply load shall be performed. During the normal
operation, the sum of currents collected by receivers shall not exceed I=3,5A (P=49W) including the battery
charging current Ibat.
As the power-supply is designed for a continuous operation and is not equipped with a power-switch,
therefore an appropriate overload protection in the power supply circuit shall be guaranteed. Moreover, the user
shall be informed about the method of isolation of the power supply from the power voltage (usually through
assignment and marking of an appropriate fuse in the fuse-box). The electrical system shall be made in
accordance with valid standards and regulations.
2.2 Installat on procedure.
1. Before nstallat on s started, the voltage n the 230V power-supply c rcu t shall be solated.
2. The power-supply shall be mounted in a selected location and connection cords shall be lead.
3. The power cables (~230Vac) shall be connected to L-N terminals of the power supply. The earth conductor shall
be connected to the terminal marked by the earth symbol . The connection shall be made by means of a three-
core cable (with a yellow and green PE protection wire). The power cables shall be lead to appropriate terminals of
the connection board through bushing.
The c rcu t of the shock protect on shall be performed w th a part cular care, .e. the yellow and
green protect on w re of the power cable shall be connected from one s de to the term nal marked
by the symbol of n the cas ng of the power-supply. Operat on of the power-supply w thout the
properly made and fully operat onal c rcu t of the shock protect on s
UNACCEPTABLE!
It can result n fa lure of dev ces and electr c shock.
4. onnect the conductors of consumers to the +AU, -AUX terminals of the terminal box on the power-supply unit.
5. If necessary, connect the conductors from the equipment to the technical outputs:
- BS A status indication (alarm panel, controller, signaling unit, LED diode, etc.)
- AW technical output of operation status of the power supply

8
RED DIODE:
• lights – the power-supply unit supplied with 230V AC
• does not light – no 230V AC supply
GREE DIODE
• lights – DC voltage at the AUX output of the power-supply unit
• does not light – no DC voltage at the AUX output of the
power-supply unit
- TAMPER signalization of power-supply unit opening
6. Set appropriate battery charging current - jumper ‘J1’ (refer to table 1 and figure 2).
7. Using the dip switch ‘JP-B’ determine whether the function of disconnecting the discharged battery U<10V (+/-
5%) is to be on or off.
The battery protect on s on f the d p sw tch ‘JP-B’ s removed.
8. Activate the ~230V/A supply (the A red diode should be permanently illuminated, and AUX diode should be
permanently illuminated)
9. heck the output voltage (the PSU voltage without load should be anywhere between 13,6 V÷ 13,9 V, and
during battery charging 11 V÷ 13,8 V). If the value of the voltage requires adjustment, the setting should be made
by means of the potentiometer P1, monitoring the voltage at the AUX output of the PSU .
10. onnect the battery in accordance with the indications: +BAT red to ‘plus’ , -BAT black to ‘minus’, (the LB diode
should go on and the lighting intensity should reduce with the charging time elapsed increasing).
11. Once the tests and control operation have been completed, lock the enclosure, cabinet, etc.
3. The power supply operat on nd cat on.
3.1 Opt cal nd cat on.
The is equipped with two diodes on the front panel:
Moreover, the PSU is equipped with three diodes indicating operation status: A , LB, AUX placed on the
P B of the power supply unit :
• AC- red d ode: under normal status (A supply) the diode is permanently illuminated. The absence of A
supply is indicated by the A diode going off.
• LB- red d ode: indicates the battery charging process; the intensity of illumination is dependent on the
charging current.
• AUX- green d ode: indicates the D supply status at the output of the PSU . Under normal status, the
diode is permanently illuminated and in the case of short-circuit or overload, the diode goes off.
3.2 Techn cal outputs:
The PSU is equipped with indication outputs allowing transmitting the information of the absence of A supply.
• BS- absence of AC supply output: - O output type indicates the loss of A supply in a normal status,
with the supply equal to 230V, the output is deactivated and in case of power supply loss the PSU activates
the output after 20s.
• AW- techn cal output of the power supply: O output type indicates failure of the power supply (short
circuit, overload) in a normal status (while correct operation) of the stabilizer, the AW output is shorted to
ground – state L (0V), in case of incorrect operation parameters (voltage, temperature) the output is
switched into hi-Z state (high impedance).
• TAMPER- output nd cates open ng the power-supply un t: output as volt-free contacts which indicate
power-supply unit door status, unit closed: N , unit opened: NO.

9
4. Handl ng and operat on.
4.1 Overloads or short c rcu ts to the PSU.
The AUX output of the PSU is equipped with the PT polymer fuse assisted protection. If the load of the
PSU exceeds I
max
(load 110% ÷ 150% @25º of the PSU power), the output voltage is automatically
disconnected and this is indicated by the green diode going off. The voltage at the output may be restored by
disconnecting the output load for the period of about one minute.
In the case of the short-circuit to the AUX, BAT output, (load 200% ÷ 250% of the PSU power) or incorrect
connection of the battery, the fuse F1 in the battery circuit becomes permanently damaged and the restoration of
the voltage at the BAT output requires the replacement of the fuse.
4.2 Battery ass sted operat on.
In the case of power failure, in the unit will instantly switch to the battery assisted operation.
In order to activate the operation of the PSU from the battery itself, connect the BAT connectors in
accordance with the indications: +BAT red to ‘plus’ and, -BAT black to 'minus’ of the battery and press and keep
depressed for five seconds the START pushbutton on the equipment board.
The PSU s equ pped w th the d scharged battery d sconnect on system (UPV); the conf gurat on of
funct ons through the d p sw tch ‘JP-B’. The battery protect on s on f the d p sw tch ‘JP-B’ s removed.
4.3 Ma ntenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the
power supply network. The PSU does not require performing any specific maintenance measures, however, in the
case of significant dust rate, its interior is recommended to be cleaned with compressed air. In the case of fuse
replacement, only the substitutes in conformity to the original ones are allowed.

10
WEEE MARK
The waste electr c and electron c products do not m x w th general household waste.
There are separate collect on system for used electr c and electron c products n
accordance w th leg slat on under the WEEE D rect ve and s effect ve only w th EU.
Not ce: The power supply unit is adapted for cooperation with the sealed lead-acid battery (SLA). After the
operation period it must not be thrown but recycled according to the applicable law.
GENERAL WARRANTY CONDITIONS
1. Pulsar K. Bogusz Sp.j. (manufacturer) grants a two-year quality warranty for the equipment, starting from the date of purchase
placed on the purchase order.
2. Should such purchase order be missing when the claim is submitted, the three-year guarantee period is counted from the date
of the manufacturing of the device.
3. The warranty includes free-of-charge repairing or replacing with a functional equivalent (the selection is made by the
manufacturer) of the malfunctioning device, due to reasons attributable to the manufacturer, including manufacturing and
material defects, unless such defects have been reported beyond the warranty period (item 1 and 2).
4. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the
manufacturer.
5. The warranty applies to complete equipment, including the type of defect specified in writing, using a properly filled warranty
claim.
6. Should the claim be accepted, the manufacturer is obliged to render warranty repairs, as soon as possible, however not later
that within 14 days from the delivering of the equipment to the service centre of the manufacturer.
7. The repair period mentioned in item 5 may be prolonged, if there is no technical capability to carry out the repairs, and in the
case that the equipment has been accepted conditionally, due to the failing of the warranty terms by the claimant.
8. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.
9. The warranty does not cover the defects of the equipment, resulting from:
- reasons beyond the manufacturer's control,
- mechanical damage,
- improper storage and transport,
- use that violates the operation manual or equipment application,
- random events, including lightning discharges, failures of power networks, fire, flooding, high temperatures and chemical
agents,
- improper installation and configuration (at variance with the rules set forth in the manual),
10. Each confirmation of structural modifications or repairs, carried out beyond the service centre of the manufacturer, or any
modification of serial numbers or warranty labels, results in the loss of the rights resulting from the warranty.
11. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the
wholesale prices suggested by the manufacturer on the day of purchase.
12. The manufacturer shall not be responsible for the defects that resulted from the damaging, malfunctioning or inability to
operate the equipment, particularly, if such defects are the result of failing to abide by the recommendations and requirements
contained in the manual, or the use of the equipment.
Pulsar K.Bogusz Sp.j.
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
e-mail: [e-mail], sale[email protected]
http:// www.pulsar.pl