Pulsar R1624T User manual

R1624T
v.1.0
R 24V/16x0,5A/TOPIC
RACK mounted power supply.
EN**
Edition: 1 from 22.09.2017
Supercedes the edition: ------------

www.pulsar.pl R1624T RACK POWER
2
Features:
DC 24V/16x0,5A uninterruptible power supply
for powering HD cameras (8A max.)
the adjustment of output voltage in the range
20V÷26V DC available from the front panel of
the power supply unit
16 outputs independently protected
by 0,5A melting fuses
high efficiency 82%
LED optical indication: AC, DC, TEMP, ALARM,
AUX1 ÷ AUX16
acoustic indication of failure
control of voltage presence at the
AUX1 ÷ AUX16 outputs
the ALARM technical output of collective failure
–relay type, activated by:
230V AC power loss
activation of the output fuse in the camera power
supply circuit
too high temperature of the PSU (>70°C)
the PSU failure
protections:
SCP short-circuit protection
OVP overvoltage protection
overvoltage protection
overload protection OLP
forced cooling (fan)
warranty –2 year from the production date
Sample application of the RACK power supply unit.
CONTENTS:
1. Technical description.
1.1. General description
1.2. Block diagram
1.3. Description of PSU components and connectors
1.4. Specifications
2. Installation.
2.1. Requirements
2.2. Installation procedure
3. Operating status indication.
3.1. LED indication
3.2. Technical output
3.3. Acoustic indication
4. Operation and use.
4.1. Overload or short circuit of the PSU output
4.2. Maintenance

www.pulsar.pl R1624T RACK POWER
3
1. Technical description.
1.1. General description.
The R1624Tpower supply unit is designed for uninterrupted power supply of up to 16 HD cameras requiring
stabilized voltage of 24V DC with the total current efficiency of 8A.The output voltage adjustment range is adjusted
via a potentiometer within the range of 20V÷26V DC. The PSU is fitted with 16 outputs protected independently
with melting fuse 0,5A. The power supply is fitted with the ALARM output of collective failure. In case of failure,
relay contacts are switched automatically, which is accompanied by acoustic and optical indication (the
corresponding led goes on). The power supply construction is based on the switch mode PSU with high energy
efficiency and is located in an enclosure adapted for mounting in standard RACK 19” cabinets.
1.2. Block diagram.
Fig.1. The block diagram of the PSU.
1.3. Description of PSU components and connectors.
Table 1. Components of the front panel of the power supply.
Element no.
[Fig. 2]
Description
AC OK –green LED, indicating the presence of 230V voltage
DC OK –green LED, indicating the presence of DC voltage
TEMP –red LED, indicating too high temperature of the power supply (>70°C)
Green LED AUX1 ÷ AUX16 –voltage indication at the outputs AUX
LED ALARM –red LED failure indication
AUX1 ÷ AUX16 –independently protected outputs
ALARM –technical output of collective failure –relay
Potentiometer, output voltage adjustment within the range of 20V÷26V DC
BUZZER, micro switch, turning ON / OFF of acoustic indication
switch in the top position, indication ON
switch in the down position, indication OFF
230V AC INPUT, power socket 230V AC, power cable 1,5m included
FMAINS,fuse in the supply circuit 230V AC, T 6,3A/250V
F1 ÷ F16, melting fuses in the camera power supply circuits AUX (+), F0,5A

www.pulsar.pl R1624T RACK POWER
4
Fig. 2. The front power of the power supply unit.
Fig.3. The view of the PSU.

www.pulsar.pl R1624T RACK POWER
5
1.4. Specifications.
- electrical parameters (tab.2)
- mechanical parameters (tab.3)
- operation safety (tab.4)
- operating parameters (tab.5)
Electrical parameters (tab. 2).
Mains supply
230V AC (-15%/+10%) 50Hz
Current up to
1A max./230V AC
Supply power
192W max.
Efficiency
82%
Output voltage
24V DC
Voltage adjustment range output
20÷26V DC
Output current
16 x 0,5A (I = 8A) max. @24V
Ripple
150 mV p-p max.
Short-circuit protection SCP
16 x F 0,5A melting fuse
Overload protection OLP
105% ÷ 150% of the PSU power, automatic return
Overvoltage protection OVP
29,5 ÷ 35V (PSU restart required)
Surge protection
varistors
Optical indication of operation:
LED: AC, DC, TEMP, ALARM, AUX1÷AUX16
Acoustic operation indication:
Piezoelectric indicator ~75dB/0,3m
The ALARM technical output of collective failure
Relay type: 1A@ 30VDC/50VAC
The FMAINS fuse in the 230V power supply circuit
T 6,3A
F1 ÷ F16, glass fuses in the cameras AUX (+)
power supply circuits
F 0,5A
Mechanical parameters (tab. 3).
Enclosure dimensions
W=19”, H=2U; 482 x 88 x 223 mm (WxHxD)
Fixation
four-point butt mounting to RACK profiles –the set include 4 M6 screws + cage nuts
Net weight
5,4kg / 5,9kg
Enclosure
Steel plate RAL 9005, black
Connectors
230V AC input: the IEC C14 socket with a fuse, power cable 1,5m
(included)
Outputs: BAT, ALARM, AUX1÷AUX16: Φ0,5-2,1 (AWG 24-12) 0,5-2mm2
Notes
Forced cooling (fan)
Operation safety (tab.4).
Protection class PN-EN 60950-1:2007
I (first)
Protection grade PN-EN 60529: 2002 (U)
IP20
Electrical strength of insulation:
- between input and output circuits of the PSU (I/P-O/P)
- between input circuit and PE protection circuit (I/P-FG)
- between output circuit and PE protection circuit (O/P-FG)
3000 V/AC min.
1500 V/AC min.
500 V/AC min.
Insulation resistance:
- between input circuit and output or protection circuit
100 MΩ, 500V/DC
Operating parameters (tab.5).
Environmental class
II
Operating temperature
-10ºC...+45ºC
Storage temperature
-20ºC...+60ºC
Relative humidity
20%...90%, without condensation
Vibrations during operation
unacceptable
Impulse waves during operation
unacceptable
Direct insulation
unacceptable
Vibrations and impulse waves during transport
According to PN-83/T-42106

www.pulsar.pl R1624T RACK POWER
6
2. Installation.
2.1. Requirements.
The PSU RACK shall be mounted by a qualified installer with appropriate permissions and qualifications for
230V/AC installations and low-voltage installations (required and necessary for a given country). The device shall
be mounted in confined spaces, according to the environment class II, with normal air humidity (RH=90% max.
without condensation) and the temperature from -10°C do +45°C.
During normal operation the total current consumption of the receivers cannot exceed I=8A.
As the PSU is designed for a continuous operation and is not equipped with a power-switch, therefore an
appropriate overload protection shall be guaranteed in the power supply circuit. Moreover, the user shall be
informed about the method of unplugging (usually through assigning an appropriate fuse in the fuse-box). The
electrical system shall follow valid standards and regulations.
2.2. Installation procedure.
1. Before installation, cut off the voltage in the 230V power-supply circuit.
2. Mount the power supply in a RACK 19" cabinet as shown below:
- Mount M6 cage nuts
- Secure the enclosure with 4xM6 screws
3. Connect the receivers’ cables to the terminals AUX1...AUX16.
4. If needed, the following technical connections can be made:
- ALARM –technical output of collective failure
5. Connect the ~230V AC power cord with the IEC C13 plug (included) to the 230V AC power supply and turn on the
power (~230V).
6. In the case of an unsafe voltage supply with frequent voltage drops in effective resistance of receiver supply cables
can occur, it is possible to adjust the output voltage using the potentiometer (20V÷26V DC) at the front panel of the power
supply.
7. Check the PSU operation indicator.

www.pulsar.pl R1624T RACK POWER
7
3. Operating status indication.
3.1. LED indication.
The PSU has 20 LED lights at the front panel:
GREEN LED:
on –the PSU is supplied with 230V AC
off –no 230V AC supply
GREEN LED:
on –DC voltage at the output of the switch mode PSU
off –no DC voltage at the output of the switch mode PSU
RED LED:
on –failure
off –no failure
RED LED:
ON –too high temperature of the switch mode power supply
(>70°C)
OFF –standard temperature of the switch mode power supply
GREEN LED:
on –DC voltage in the AUX1…AUX16 output
off –no DC voltage in the AUX1…AUX16 output
3.2. Technical output.
The power supply is fitted with the ALARM output of collective failure (relay type). A collective failure can
be triggered by the following events:
- 230V AC mains power failure
- Melting fuse activation F1÷F16
- Failure of the switch mode power supply
- Too high temperature of the switch mode power supply (>70°C)
Fig. 4. Electrical diagram of the ALARM collective output of failure.
CAUTION! In Fig. 4 the set of contacts shows a potential-free status of the relay, which
corresponds to power supply failure.

www.pulsar.pl R1624T RACK POWER
8
3.3. Acoustic indication.
A collective failure is indicated by the piezoelectric indicator, 1 beep every second. The acoustic indication
can be turned off by changing the ON / OFF position of the switch .
switch in the up position, indication ON
switch in the down position, indication OFF
4. Operation and use.
4.1. Overload or short circuit of the PSU output.
The AUX1 ÷ AUX16 power supply outputs are protected against short circuit by melting fuses; in the case
of fuse failure, it should be replaced with a fuse of the same type.
4.2. Maintenance.
Any and all maintenance operations may be performed following the disconnection of the PSU from the
power supply network. The PSU does not require performing any specific maintenance measures. In case of fuse
replacement, use a replacement of the same parameters.
WEEE LABEL
Waste electrical and electronic equipment must not be disposed of with normal household
waste. According to the European Union WEEE Directive, waste electrical and electronic
equipment should be disposed of separately from normal household waste.
Pulsar
Siedlec 150, 32-744 Łapczyca, Poland
Tel. [phone], Fax. [phone]
E-mail: [e-mail], [e-mail]
http:// www.pulsar.pl, www.zasilacze.pl