Pure n Natural Systems FM-2000 User manual

FM-2000 AIR CLEANER USERS MANUAL
READ AND SAVE THESE INSTRUCTIONS
Pure n Natural Systems, Inc. recommends that a licensed electrician or licensed
contractor install units.
WARNINGS:
1. Always unplug or disconnect the air cleaner from power supply before servicing.
2. To reduce the risk of electric shock or injury to persons, do not expose to water or
rain, do not use in a window.
3. Do not use this fan with any solid state speed control device.
FILTER CHANGING:
1. Pre Filter - Replace every 3 to 4 weeks.
2. Carbon Panel Filter - Replace at least every 2 months.
3. H.E.P.A. Filter - Replace at least every 12 months.
Step 1. The Pre Filter is located behind the intake door (service door). The Pre Filter is a
blue and white polyester, pre-tack filter. The intake door is located closest to the
HI/OFF/LO switch on the face of the system. Unclip the two latches on the intake door
and the door will swing down. The Pre Filter is the first filter behind the intake door. Peel
away dirty Pre Filter and discard. Install the new Pre filter with the white side out. Close
door. DO NOT WASH PRE FILTERS.
Step 2. The carbon filter is located behind the Pre Filter. Follow Pre Filter changing
instructions from Step 1. Remove Carbon Filter, discard and replace with new Carbon
Filter. DO NOT WASH CARBON FILTERS.
Step. 3. Remove the adjustable louver door. Remove the H.E.P.A. Bar. The H.E.P.A.
Filter is a pleated media surface with a metal frame. Slip the H.E.P.A. Filter out of the
system, discard and replace with new H.E.P.A. Filter. DO NOT WASH H.E.P.A.
FILTER.
Filter maintenance may vary according to each situation.
For any questions, please contact our customer service department at 1-800-237-9199.

INSTALLATION OF FM-2000 AIR CLEANER
EQUIPMENT:
1. Each FM-2000 unit is equipped with two (2) eye bolts, two (2) eye lags and
industrial hanging wire for easy installation.
2. The FM-2000 has a ten foot power cord and a three prong grounded plug.
Electrical: 120 Volts, 9 Amps.
3. Each unit includes a 1-year supply of filters, which consists of twelve (12) pre-
filters, three (3) charcoal filters and one (1) H.E.P.A. filter.
INSTALLATION:
Step 1. Remove the system from the shipping container. Remove the adjustable louver
door from inside the system. After you have removed the adjustable louver door, remove
the industrial staples and the H.E.P.A. bar and then slip out the H.E.P.A. filter. The
H.E.P.A. filter is a pleated media surface with a particle board frame. Removing the
H.E.P.A. filter will make the system lighter for installation purposes.
Step 2. On either side of the system there are two mounting holes where the eye bolts are
inserted. It is easiest to screw the eye bolts into these mounting holes before mounting
into the ceiling. If the area above the drop ceiling is tight for space, then you may need to
put the eye bolts in the mounting holes after you have the system into the drop ceiling.
Step 3. Remove the ceiling tile(s). The system will fit into either one 2’x 4’ or two 2’x 2’
tiles.
Step 4. A system being installed into a drop ceiling that has joints, steel girders or
exposed beams above can be hung without the eye lags (see step 5). At least one eye lag
will be needed if your system is being installed into a ceiling that is solid above (see step
6).
Step 5. Locate either a joist, girder or beam that is directly above the tile where your
system will be installed. After you have located a joist, girder or beam, drape the
industrial hanging wire over the apparatus so that either side is evenly dispersed. Line up
the eye bolts with the hanging wire so they are vertical. Thread one end of the hanging
wire through one of the eye bolts, loop the wire and twist tightly together. Thread the
opposite end of the hanging wire through the opposite eye bolt. Pull the wire tight. The
system should be only slightly resting on the grid work of the drop ceiling. After you
have adjusted the weight of the system on the grid work, then loop the wire and twist
tightly together.

Step 6. Locate a stud in the solid ceiling that is directly above the tile where the system
will be installed. Fasten the eye lag into the stud making sure to line up the eye lag with
the eye bolts on the system so the hanging wire will hang vertically. Thread the hanging
wire through the eye lag so that either side is evenly dispersed. Thread one end of the
hanging wire through one eye bolt, loop the wire and twist tightly together. Thread the
opposite end of the hanging wire through the opposite eye bolt. Pull the wire tight. The
system should be only slightly resting on the grid work of the drop ceiling. After you
have adjusted the weight of the system on the grid work, then loop the wire and twist
tightly.
Step 7. After the system is installed, put your H.E.P.A. filter back into the system. Make
sure the H.E.P.A. filter is snug. Replace the H.E.P.A. bar and the adjustable louver door.
For any questions, please contact our customer service department at 1-800-237-9199.

FM-2000 FLUSH MOUNT AIR CLEANER
APPLICATION
The FM-2000 flushmount Air Cleaner is designed to drop into a suspended ceiling. It
replaces either 1 - 2' x 4' tile or 2 - 2' x 2' tiles from the suspended ceiling. In order to
install the FM-2000 flushmount easily, the clearance above the
suspended ceiling needs to be at least 18" and is recommended
that the air cleaner is installed in areas that do not exceed a 13
foot ceiling height. The weight of the system does not rest on the
ceiling grids but is secured above the suspended ceiling to a
permanent structure such as a joist or beam. All filters in the
FM-2000 flushmount are accessible from the louvered door and
hinge door on the face of the system. 1 unit recommended for
every 2000 square feet.
• 2000 C.F.M.
• Fits in 2 - 2'x2' or 1 - 2'x4' ceiling tile
• 46-3/4" L x 23-3/4" W x 17" H
• Aluminum
• Shipping Weight - 135 lbs.
• 9.2 amps, 120V, Hi/Lo/Off settings
• 10 ft. power cord, 3 prong ground plug
• Three Filter System: HEPA (21-1/2" x 16-1/2" x 5-7/8"), Activated Carbon, Pre-Filter
• All systems carry a lifetime motor/blower warranty
• All electrical components and fan motor are UL Listed and CSA Certified.
For any questions, please contact our customer service department at 1-800-237-9199.
Pure n Natural Systems, Inc.
P.O. Box 1137 ● Streamwood, IL 60107
Toll-Free –1-800-237-9199 ● Fax – 847-470-1686
www.purennatural.com