Pure n Natural Systems LA-1400S User manual

LA-1400S CEILING MOUNT AIR CLEANER
INSTALLATION INSTRUCTIONS
IT IS IMPORTANT TO READ THE FOLLOWING INSTRUCTIONS CAREFULLY –DAMAGE
TO THE PRODUCT OR TO INSTALLER AND PROPERTY COULD RESULT IF
INSTRUCTIONS ARE NOT FOLLOWED.
IMPORTANT
1. Do not connect the power source until after the unit is mounted. Shock and/or damage could
result.
2. Be sure to shut the unit off prior to any service work.
3. Wear gloves to protect hands during installation as well as to keep surface of air cleaner free from
dirt and smudges.
4. All electrical wiring must comply with applicable codes and local ordinances. DO NOT connect
power supply until air cleaner has been installed and/or checked.
HOW TO DETERMINE THE NUMBER OF ELECTRONIC AIR CLEANERS REQUIRED
1. Calculate the volume of the room. Volume (cubic feet) = Length x Width x Height
2. Determine the circulation of the air needed, based upon 8 air changes per hour for average
conditions, to reduce the smoke and pollution. Use 16 air changes per hour for high
concentrations of smoke and contaminants, or when one has a desire to reduce smoke and
pollution even further.
3. The LA-1400S produces 800 cfm at low speed and 1100 cfm at high speed. To establish the
correct number of units to use, you should calculate the cubic feet of air in the area to be
cleaned, and then use a figure of 8 air changes/hour in that area for average cleaning, and 16 air
changes per hour for very polluted or smoke filled conditions. You should remember that the
slower the air passes over the surface of the air cleaner, the more efficiently the unit will
operate. Therefore, when calculating the number of units needed, take into account air flow and
cleaning capacity.
EXAMPLE #1
ROOM DIMENSIONS: 50’ X 100’ X 10’ CEILING
TYPE OF AREA: RESTAURANT OR LOUNGE
AIR CHANGES DESIRED: 16/HOUR
STEP 1 –Volume
50’ x 100’ x 10’ = 50,000 CU FT
STEP 2 –Volume to be cleaned
50,000 CU FT x 16 air changes per hour = 800,000 CU FT per Hour
STEP 3 –Volume/Minute to be cleaned
800,000 CU FT per Hour / 60 Minutes per Hour = 13,333 CU FT Min (CFM)
STEP 4 –Number of units needed
13,333 CFM / 1,1000 (CFM of unit) = 12.09 or 12 units

EXAMPLE #2
ROOM DIMENSIONS: 50’ X 30’ 10’ CEILING
TYPE OF AREA: OPEN OFFICE AREA WITH MULTIPLE PERSONNEL
AIR CHANGES DESIRED: SOME SMOKERS & 20 DESKS –USE 8 CHANGES/HOUR
STEP 1 –Volume
50’ x 30’ x 10’ = 15,000 CU FT
STEP 2 –Volume to be cleaned
15,000 CU FT x 8 air changes per hour = 120,000 CU FT per Hour
STEP 3 –Volume/Minute to be cleaned
120,000 CU. FT per Hour / 60 Minutes per Hour = 2,000 CU FT Min (CFM)
STEP 4 –Number of units needed
2,000 CFM / 1,1000 (CFM of unit) = 1.8 or 2 units
PROPER LOCATION OF THE MODEL LA-1400S AIR CLEANER
Locate electronic air cleaners consistent with existing air circulation in the room so that the heating and
air conditioning systems are complemented by the air cleaners. Air cleaners must be mounted to strong
structural parts of the ceiling with adequate head clearance, and should be a minimum of 10 feet from air
intake or exit ductwork.
MOUNTING YOUR LA-1400S ELECTRONIC AIR CLEANER
The LA-1400S comes with a 6’ cord, but it is the responsibility of the purchaser to provide an adequate
outlet which meets local codes. An approved extension cord may be used if it meets local and national
codes.
The LA-1400S is designed with 4 mounting holes on the top and bottom of the unit. Eye bolts are
provided with the units so that they may be hung by chains from supporting beams on the ceiling. If you
choose the optional wall mount for the LA-1400S, see the instruction sheet included with the Model
10009 wall mount. The mount using the included eye bolts, follow the instructions below. The unit may
be hung so the air flow is from the left to the right, or from the right to the left depending on the needs of
the customer.
1. Choose an area which compliments the rest of the air flow in the room
before you mount the air cleaner.
2. Make sure you have correct lengths of chain, and that it is capable of
sustaining the weight of the unit. Standard hardware item, link chain with
working load of at least 100 lbs. Also make sure you have mounting lag
screws or equivalent fasteners to attach the chain to the ceiling beams or
studs. In some instances, it may be necessary to construct a mounting
frame to properly suspend the unit.
3. Locate the ceiling studs or beams and attach the correctly sized chain.
Chain length should be such that it will not allow the LA-1400S to have a
floor to bottom height which would pose a hazard to room occupants. A minimum height of eight
feet from floor to bottom of unit is recommended when chain hung.
4. After securing the chain to the ceiling studs or beams, us 4 “S” hooks on the chain to mount the
air cleaner cabinet to the chain. (It is a good idea to take out the electronic cell and other parts to
make the cabinet lighter when mounting and then to replace the internal parts into the unit.) The

first thing to remember is to remove the shipping screw which holds the cells of all units
while in transit from the factory. This screw is located at the base of the cell and locks the cell
to the cabinet. Remove it with a Phillips head screwdriver.
5. After making sure all the parts are securely replaced into the unit, you may now test the operation
of the unit by plugging it into the nearest outlet and turning the air cleaner on.
OPERATING INSTRUCTIONS
1. Turn the unit on by selecting one of the following modes of operation located on the control box:
a) Low –Air is circulated and the cell is activated
b) High –Air is circulated and the cell is activated
2. Indicator light will appear when any of the “on” modes are selected indicating there is electrical
power to the unit.
LA-1400S CEILING MOUNT AIR CLEANER MAINTENANCE
WASHING THE ELECTRONIC CELLS AND PREFILTER
NOTE: FAILURE TO CLEAN CELLS WILL VOID WARRANTY
The electronic cell must be inspected frequently and the collected dirt removed regularly to prevent
excess accumulation which may result in risk of flashover and fire damage. Inspect electronic cells and
filters every week for the first month or two to determine your required cleaning schedule. Use the
following as a guide for your establishment;
Cocktail Lounge –Every week (if run daily)
Conference Room –Once every month
Restaurant –Every week (if run daily)
REMOVAL OF ELECTRONIC CELL(S) PREFILTER SCREEN AND CARBON
AFTERFILTER
1. Turn the Electronic Air Cleaner off.
2. Disconnect the power supply cord.
3. Open the door containing the cells and remove the prefilter screen and the carbon afterfilter.
4. Slide the carbon filter and the prefilter screen from the cells.
NOTE: The first time you remove the cell from the unit you must first remove the small packing screw
which is used to anchor the cell during shipment.
CLEANING THE PREFILTER SCREENS
Use a damp rag to wipe off the inside and outside of the cabinet which acts as the first prefilter. Remove
the black prefilter screen from the cell assembly and wipe off with a damp cloth. It is your second
prefilter.
CLEAN CARBON AFTERFILTERS by vacuuming or brushing. DO NOT WASH. Replace carbon
afterfilters as needed, using the following as a guide;
Cocktail Lounge –1-2 months

Restaurant –1-3 months
Beauty Salon –1-3 months
Conference Room & Office –6-12 months
REMOVE DIRT OF ELECTRONIC CELL by one of the following methods;
1. Run through full cycle on dishwasher using a detergent marked “safe for aluminum”. Allow to
dry thoroughly.
2. Soaking Method:
a) Use a washing container large enough to hold the cells, such as a laundry tub or trash
container.
b) Fill container with hot water.
c) Dissolve 1 to 1-1/2 cups dishwasher detergent or use a detergent marked “safe for
aluminum”.
d) Soak cell for 20 minutes, agitate and remove.
e) Rinse cell with a fine spray of water.
f) Soak cell in clean hot water for 15 minutes.
g) Allow cell to dry thoroughly
3. High Pressure Steam Cleaner / Car Sprayer Method
a) Saturate cells.
b) Spray on liquid detergent or cleaning solution marked “safe for aluminum”.
c) Wash.
d) Rinse with hot water.
e) Allow cell to air dry thoroughly.
Inspect cells. If any dirt remains, repeat cleaning procedure. If it is necessary to repeat the cleaning
procedure, it is advisable to increase the washing frequency. Check cells for bent plates and broken
ionizing wires. Reinsert cells and carbon filters. DO NOT INSERT CELLS if not completely dry.
Approximately every 6 months, place a drop of oil in the two oil holes on the fan motor. Use non-
detergent electric motor oil only. (SAE 20)
REPAIR AND MAINTENANCE
Before attempting any repairs on your Electronic Air Cleaner, check the following items
first. 1. Check fuse.
2. Check for electrical power to unit.
3. Check that the electronic cell, prefilter screen and carbon filter are “CLEAN”, dry and properly
installed in the Air Cleaner.
Repair work should only be performed by a trained, experienced serviceman. Check with your dealer for the repair
station in your area.

TROUBLE SHOOTING ELECTRONIC AIR CLEANERS
CAUTION: During repair procedures dangerous line voltage circuits are exposed; use care to avoid the hazard of
electrical shock or possible damage to the unit. The following examples are used to aid the serviceman in trouble
shooting any malfunction in the Electronic Air Cleaner quickly and properly.
INDICATOR LIGHT DOES NOT WORK
1. Check fuse.
2. Plug power supply into the proper receptacle.
3. Measure line voltage at power source (120V depending on unit).
4. Replace light.
COLLECTOR CELL MALFUNCTION
1. Remove electronic cell and inspect for bent collector plates. Make sure cell is thoroughly clean and dry.
2. Return electronic cell to air cleaner cabinet. Do not install prefilter screen at this time.
3. Turn air cleaner on and use a long, insulated screw driver to generate an arc between the collector cell
plates; or, use the high voltage DC probe, measure 4,800 at the collector plates.
FAN MOTOR DOES NOT RUN
1. Check power source and fuse.
2. Measure line voltage at two speed switch.
3. Measure line voltage at fan motor.
4. Replace fan motor.
For any questions, please contact our customer service department at 1-800-237-9199.

LA-1400S AIR CLEANER SPECIFICATIONS
The LA-1400S electronic air cleaner can be used in bars, casinos,
restaurants, meeting halls, bowling alleys, clubs or anywhere you
desire clean, fresh air. The LA-1400S's triple action filtering system
works like a pollution magnet, trapping up to 97% of particles as
small as one-millionth of an inch for a healthier business or
industrial environment. The prefilter removes dust, hair, lint and
larger dust particles; the electrostatic filter removes particles as
small as 0.01 microns in size, such as tobacco smoke, fumes, dusts,
mold spores, and vapors; and the activated charcoal after-filter helps
to eliminate even the most stubborn odors, as in cooking, welding
and similar odors. 1 unit recommended for every 800 square feet.
Capacity - 2-Speed (high - 1,300 CFM, low - 800 CFM)
Dimensions - 21.5" W x 19.5" H x 17" L
Shipping Weight - 65 lbs.
Electrical - 5 amps, 120V, AC/60Hz - 720 watts
Electronic Cell Collection Area - 13,284 square inches
Sound Level - 53 - 65 dB(A)
Particle Removal - As small as 0.01 microns
7 year limited warranty
All electrical components and fan motor are UL Listed and CSA Certified.
Pure n Natural Systems, Inc.
P.O. Box 1137 ● Streamwood, IL 60107
Toll-Free –1-800-237-9199 ● Fax – 847-470-1686
www.purennatural.com