PURE PureSteam XL User manual

Standing Fabric Steamer
OPERATION MANUAL
READ BEFORE USING

1
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ……………..………………….......... 1-2
PRODUCT DIAGRAM.........................................………..……….…........…... 3
ASSEMBLING PURESTEAM XL ……………………………….…………….…... 4
USING PURESTEAM XL ……………………………….…………….….…....…... 5
PRESSING WITH STEAM.……………………………............…......…….6
QUICK STORAGE………………….………………...............……..... 7
CLEANING & LONG-TERM STORAGE………….........….............……...... 7-8
PROBLEM SOLVING GUIDE...........................................…………………… 9
REMOVING MINERAL BUILDUP….......................................................... 10-11
PRODUCT SPECIFICATIONS…................................................................. 11
WARRANTY & PRODUCT REGISTRATION......................…………………… 12

2 3
IMPORTANT SAFETY INSTRUCTIONS (Cont'd.)
15. DO NOT let the power cord touch hot surfaces or water. The power cord
should not be kinked or obstructed in any way.
16. DO NOT bend, twist or fold the steam hose.
17. DO NOT steam plastic, vinyl, leather or suede materials.
18. Always keep the steam nozzle elevated above the water container. Do
not lay the hose on the oor.
19. PureSteam XL has a grounded plug. As a safety feature, this plug will t
in a three-prong outlet only one way. If the plug does not t in the outlet,
do not attempt to bypass this safety feature.
20. DO NOT pull the power cord to disconnect it from an outlet. Instead,
grasp the plug to remove it from the outlet.
21. To reduce the risk of contact with hot water and steam, always check
PureSteam XL for steam leaks. Operate PureSteam XL with the steam
nozzle placed in its holder; and inspect the base, hose, handle, and
nozzle for steam leaks.
22. DO NOT operate another high-wattage appliance on the same circuit as
PureSteam XL. Doing so may cause a circuit overload,
23. If an extension cord is absolutely necessary, a 3-pronged cord rated for
at least 20 amperes should be used. Cords rated for less amperage may
overheat. Care should be taken to arrange the cord so that it cannot be
inadvertently pulled or tripped over.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
When using PureSteam XL you should always follow these basic safety
precautions:
1. Use PureSteam XL for its intended purpose only.
2. DO NOT submerge PureSteam XL in water or other liquids.
3. DO NOT allow PureSteam XL to be used as a toy.
4. Keep out of reach of children and always use close supervision when
steaming by or near children.
5. Unplug PureSteam XL from the electrical outlet before adding or
removing attachments and before lling, emptying or cleaning the water
tank.
6. STEAM CAN CAUSE SERIOUS BURNS. Keep your hands, skin, and
hair away from the steam nozzle openings while steaming.
7. DO NOT touch the steam hose while steaming. It gets hot and can burn
your skin.
8. DO NOT point steam nozzle in the direction of people, plants, or pets
while steaming.
9. NEVER attempt to steam clothes while you are wearing them.
10. DO NOT operate PureSteam XL if it is damaged in any way—especially
if the power cord or plug is damaged. Doing so may result in fire,
electrical shock, or injury.
11. DO NOT leave PureSteam XL unattended while plugged in or in
operation.
12. Allow PureSteam XL to cool before storing it.
13. DO NOT use accessories that are not made for PureSteam XL. Doing so
may cause re, electrical shock, or injury.
14. Always turn the power switch off before unplugging or plugging in
PureSteam XL.
1 2

4 5
ASSEMBLING PURESTEAM XL
1: Remove all contents in the box to ensure you
have all the pieces listed on Page 3.
2: Fully extend the Telescopic Pole, To do so, rst
open the clips and loosen the poles. Then, fully
extend the poles and close the clips to lock in
place (see Figure 2). Make sure the pole is locked
into place and cannot be pushed down.
NOTE: To ensure a steady ow of steam it is best
to fully extend the steam hose and telescopic pole
when operating PureSteam XL.
3: To attach the hanger/nozzle holder, align the
tabs in the holder with the grooves on the pole
and push down (see Figure 3).
4: Insert the bottom of the telescopic pole into the
pole insert base (see Figure 4) so that the nozzle
holder faces the rear of the steamer. Pointing
the nozzle holder towards the rear will ensure
the stability of the steamer when garments are
hanging from the hanger holder.
5: To attach the steam hose: Align the screw at the
bottom of the steam hose with the unit base, and
then turn the screw clockwise to tighten the hose
with unit (see Figure 5). Then, place the steam
nozzle on the nozzle holder.
CAUTION: To prevent steam from causing bodily
injury or damage to surfaces, always hang the
steam nozzle on the nozzle holder when not in
use. Do not lay the steam hose on the floor as
condensation may occur and cause unwanted
water droplets in the steam.
CAUTION: Pulling on the steam hose with
excessive force will damage it and may cause a
steam leak.
PRODUCT DIAGRAM
3 4
1: Steam Nozzle
2: Steam Handle
3: Hanger/Nozzle Holder
4: Steam Hose
5: Telescopic Pole
6: Pole Insert Base
7: Water Fill Tank
8: Power Switch
9: Wheel
10: Power Cord
11: Unit Base
12: On/Off Light
13: Steam Hose Base
PureSteam XL also
includes two attachments: a
Garment Hanger and Fabric
Brush (not shown).

6 7
PRESSING WITH STEAM
1. To steam a garment, secure it carefully using the included garment
hanger.
CAUTION: Be careful when handling garments on the hanger.
Pulling on the garment with too much force may cause the unit to tip.
CAUTION: Hot steam can cause serious burns.Use caution.
2. Grasp the steam handle and place the steam nozzle at the bottom of
the garment. Steam will rise along the inside and outside of the fabric,
removing wrinkles. Slowly slide the nozzle vertically, from the bottom to
the top of the garment.
NOTE: Do not allow kinks to form in the hose at any time.
3. Remove the steam nozzle from the garment, and smooth the fabric with
your free hand.
4. Repeat steps 2 and 3 as necessary until the fabric is wrinkle free.
5. When steaming horizontally keep the steam 4 inches from the fabric.
6. To remove wrinkles from towels, handkerchiefs and napkins, drape them
over a rod or towel rack and gently steam.
7. Heavier fabrics may require repeated steaming.
8. To remove stubborn wrinkles, steam both sides of the fabric.
9. The fabric brush may also be used to remove tough wrinkles.
USING PURESTEAM XL
1. Turn off PureSteam XL and unplug the power cord.
2. Remove the water tank. Turn it upside down and unscrew the cap.
3. Fill the water tank with cool water and replace the cap.
NOTE: To prolong the life of PureSteam XL, we recommend using
distilled or de-mineralized water.
4. Place the water tank on the water reservoir. You should hear water
owing into the water reservoir for a short time.
CAUTION: Do not let the steamer operate with a dry water tank. Doing
so will cause damage to the unit.
5. Plug PureSteam XL into a properly grounded three-pronged outlet.
6. Turn the power switch on. The steam will be ready in 45 seconds.
7. To steam your garments hold the handle of the steam nozzle upright at
all times. Tilting it downward, even for a few moments, can cause a leak
that can burn your skin.
8. When nished steaming, turn the power switch off.
5 6

8 9
QUICK STORAGE
1. Turn off the unit and unplug the power cord.
2. Wrap the steam hose around the telescopic pole one time. Do not fold or
bend the hose.
3. Hang the steam nozzle from the nozzle holder.
4. Loosen the top two sections of the telescopic pole and collapse to a
compact height.
5. Roll the unit to a convenient storage location.
CLEANING AND LONG-TERM STORAGE
For maximium performance, you should clean PureSteam XL weekly. Using
distilled or de-mineralized water will help prevent buildup and require less
frequent cleaning. Do the following to clean:
1. Turn the unit off and unplug the Power Cord.
2. Wait for the unit to cool completely (at least 30 minutes).
3. Remove the steam hose and the telescopic pole, and set them aside.
4. Carry the unit to a sink or tub.
5. Remove and drain the water tank. Rinse with fresh water and drain
completely.
6. Tilt upside down to facilitate removal of all water.
CLEANING AND LONG-TERM STORAGE (Cont'd)
7. Flush the unit by lling the water reservoir and the hose base with fresh
water and draining completely.
8. Place the water tank back on the water reservoir.
9. Reattach the telescopic pole and steam hose.
10. Follow steps 3-6 of the Quick Storage procedure on the previous page.
7 8

10 11
PROBLEM SOLVING GUIDE
PROBLEM CAUSE SOLUTION
The unit fails to steam. 1. Steamer is not
plugged in.
2. Water tank is
empty.
3. There may be
mineral buildup.
1. Plug into electrical
outlet.
2. Fill water tank
3. Follow procedure
on the next page
Water drips from nozzle Condensation in hose Extend the hose
vertically to allow water
to drain back into the
water reservoir.
Excessive gurgling of
hose and steam nozzle
Condensation in hose Some gurgling is a
natural effect of the
steaming process. For
excessive gurgling,
extend the hose vertically
to allow water to drain
back into the water
reservoir.
Steam is intermittent Mineral Buildup in the
unit
It is normal for the unit
to periodically stop
steaming for a few
seconds. If the steam
stays off for longer
periods, follow the
procedure on the next
page.
REMOVING MINERAL BUILDUP
One common problem with steamers is mineral buildup caused by the high
mineral content often found in tap water. Mineral residue inside of the internal
pipes and heater can cause intermittent steaming or, in some cases, no
steaming at all.
NOTE: To reduce or eliminate mineral buildup we recommend the use
of de-mineralized or distilled water in the unit.
The procedure below can be used to reduce mineral buildup. If you are
unable to use de-mineralized or distilled water, we recommend you follow this
procedure monthly.
1. Turn the unit off and unplug the power cord.
2. Remove the steam hose and telescopic pole from the unit.
3. Drain the water reservoir by following steps 1-7 of the Cleaning and
Long-Term Storage procedure on Page 7. Leave the water tank off the
unit.
4. Mix a solution of 50% vinegar and 50% water. In most cases, 2 cups of
this solution will be sufcient.
5. Slowly pour the water-vinegar solution into the hose base connector as
shown in Figure 6.
9 10

12
.
REMOVING MINERAL BUILDUP (Cont'd)
6. Continue pouring the solution into the hose base until the solution
appears near the top of the hose base. Pour additional solution into the
water reservoir until it is about half full.
7. Allow solution to sit for 40 minutes.
8. Drain the solution from the water reservoir allowing the liquid to drain into
a sink or tub.
9. Drain the solution out of the hose base by tilting the unit over a sink or
tub and pouring the water out of the hose base.
10. Pour clean water in the hose base and water reservoir inlet and drain.
11. Repeat this step until the vinegar smell dissipates.
12. Reassemble the unit and operate normally.
PRODUCT SPECIFICATIONS
Base Dimensions 14 in x 9.25 in x 12.2 in
Total Height 5 ft, 5 in
Weight 10 lbs, 9 oz
Water Tank Capacity 1/2 gal
Heat Up Time 45 seconds
Steam Time up to 60 minutes per tank rell
Steam Hose Length 5-ft cloth-covered hose
Input 120V AC 60Hz 1500w
Power Cord Length 7 ft
WARRANTY INFORMATION
Pure Enrichment offers an industry-leading 2 Year Warranty on PureSteam XL.
For warranty requests or questions please visit pureenrichment.com.
PRODUCT REGISTRATION
To ensure your 2 Year Warranty, receive product updates, and streamlined
customer support, please register your PureSteam XL at pureenrichment.com.
11 12

14
Santa Ana, CA 92704
www.pureenrichment.com