Purell Onvation 8 series User manual

PURELL

ONVATION 8 Series PAN Module Setup and Validation

Objectives

You will learn how to perform the following system setup procedures:

•Recording required MAC ID of PURELL PAN Module

•Installing PAN Module into 8 Series Dispenser

•Provisioning the PAN Module to the ONVATION Hub

•Validating PAN Module connectivity

•Troubleshooting setup issues

Equipment

•PURELL ONVATION 8 Series PAN Modules

•Recording device for MAC ID

•ONVATION Installer App

Module MAC ID Identification and Recording

Step Illustration

1. Open module static bag and record MAC ID onto

recorder with association to dispenser location.

2. Record Dispenser location on the static bag.

3. Using recorded MAC ID’s enter them into the

ONVATION Installer App.

4. Install the Dispenser per the Dispenser

Installation Guidelines.

Step

5. Open the 8 Series dispenser by

pressing in the

left and right buttons on the side to release the

door on the dispenser.

6. Discard the circuit board cover.

Insert the module by aligning the module

connection receptacle with the SMARTLINK

connector on the pumphouse.

Load the refill into the dispenser and l

dispenser door back up to close it

(if you are

installing using adhesive for the

dispenser, utilize

the refill collar shipped with the modules

than the full refill to ensure proper adhesion

9. Once the module is installed d

ispense 3x so the

module can recognize what dispenser it is

connected to.

10. Confirm on the ONVATION

Installer App that the

module has ‘checked-

in” with the ONVATION

Hub.

Illustration

pressing in the

left and right buttons on the side to release the

Insert the module by aligning the module

connection receptacle with the SMARTLINK

Load the refill into the dispenser and l

ift the

(if you are

dispenser, utilize

the refill collar shipped with the modules

rather

than the full refill to ensure proper adhesion

ispense 3x so the

module can recognize what dispenser it is

Installer App that the

in” with the ONVATION

Page 2of 6

Wi-Fi/BLE Provisioning Exceptions

Issue Code

Dispenser Not Communicating with

Onvation Module

If the dispenser is not communicating with Onvation, then try

the following steps:

1. Hold a magnet near the {Special Location} on the

module. The Red and Green LEDs will turn on.

Remove the magnet immediately when the LEDs turn

on.

If the magnet is held for a short period of time, the

module will enter pairing mode. Once paired, the

module will connect to Onvation.

2. Alternately a factory reset may be performed:

If the magnet is held for a long period of time, all LEDs will turn

on. This means a factory reset of the module is performed.

All parameters are erased. The module enters a “Dispenser

Detect” state where a dispense must be performed after a

factory reset.

PAN Module Light Patterns

Status

Pairing Mode

If the magnetic switch is engaged for 500ms (1/2 second), the device will enter pairing mode.

When the button is released, the module will enter pairing mode and will attempt to make a connection to the hub.

Note: We have seen instances where on the first connect to the hub, the hub will determine that it no longer has bond

information and will automatically disconnect before parameters are sent. The module will then re-attempt a

connection attempt 1 minute later and this time, the connection will succeed.

Pairing mode will be ignored in certain modes such as the connected mode.

Factory Reset

If the button or magnetic switch is engaged for 4 seconds, the device will perform a factory reset. When a factory

reset is performed, any settings and bond information are erased from the module. In addition, the module will restart

in a mode where it attempts to detect the dispenser type.

Defaults

The default settings for the module board are as follows:

Synchronization Interval: 60 minutes (may be set to any value [30-720])

Dispense Count Threshold: 50 dispenses (may be set to any value [5-255])

Device Compliance

Onvation Module FCC/IC Label

Please include on dispenser packaging or enclosure the following:

"Contains FCC ID: O76ONVATION, IC: 10391B

This equipment has been tested and found to comply with the limits for a Class A digital d

the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will

be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This

device may not cause harmful interference, and (2) This device must accept any in

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

authority to operate the equipment

This device complies with Indu

stry Canada license

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de

l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

compromettre le fonctionnement.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This

device may not cause harmful interference, and (2) This device must accept any interference received, including

interference that may cause undesired operation.

Please include on dispenser packaging or enclosure the following:

"Contains FCC ID: O76ONVATION, IC: 10391B

-ONVATION"

This equipment has been tested and found to comply with the limits for a Class A digital d

evice, pursuant to part 15 of

the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

be required to correct the interference at his own expense.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This

device may not cause harmful interference, and (2) This device must accept any in

terference received, including

interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's

stry Canada license

exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the

device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)

l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This

device may not cause harmful interference, and (2) This device must accept any interference received, including

interference that may cause undesired operation.

Page 4of 6