Owon SLC601 User manual

1
SLC601 ZigBee Smart Relay Module
Quick Start Guide

2
WARNING: Failure to follow these safety notices could result in 󽗉re,
electric shock, other injuries, or damage to the Smart Relay Module
and other property. Read all the safety notices below before using
the Smart Relay Module.
• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit on your own.
• Do not expose the unit or its accessories to 󽗊ammable liquids, gases
or other explosives.
Safety Handling

3
Technical Speci󽗉cations
Wireless Connectivity
ZigBee • 2.4GHz IEEE 802.15.4
ZigBee Pro󽗉le • ZigBee HA1.2
RF Characteristics
• Operating frequency: 2.4GHz
• Range outdoor/indoor: 100m /
30m
• Internal PCB Antenna
Physical Speci󽗉cations
Operating Voltage • 100~240 Vac 50/60 Hz
Power consumption • < 0.7W
Max. Load Current
• 5A Resistive Load:
1) 500W incandesent bulb or
halogenated bulb
2) 100W 󽗊uorescent lamp
3) 60W LED lamp
Operating environment • Temperature: -20℃~+55℃
• Humidity: ≤ 90% non-condensing
Dimensions • 55.3 (L) x 39(W) x17.7(H) mm
Weight • 42g
Certi󽗉cate • CE, ROSH

4
The SLC601 is a smart relay module that allows you to turn the power
on and o󽗈 remotely as well as set on/o󽗈 schedules from the mobile
app.
This guide will provide you with an overview of the product and help
you get through the initial setup.
Note: Use the smart relay module for no more than rated current 5A.
• ZigBee HA1.2 compliant
• Upgrades existing lighting to a remote control lighting system (HA)
• Easy installation by simply inserting the Power Relay into the existing
power line
• Extra control cables available to integrate with existing physical
switch
Features:
1Welcome

5
Installation
2
Please refer to the installation diagram below to install the smart relay
module.
Please make sure the main power in your facility is off before
installing.
Op�onal
Control light or hea�ng/
ven�la�on to On/Off
Physical switch
Live
Neutral
Wiring diagram

6
Get to know your device
3
Reset button
LED status What it means
Green The load is ON.
Red The load is OFF.
Steady light Device has joined a ZigBee network.
Keep Flashing Device has not joined a ZigBee
network.
Flashing rapidly for 3 times Identify mode/Reset
LED indicator
The LED status gives the following information:
Reset: Press and hold the reset button for ten seconds until the LED
indicator 󽗊ash for 3 times at third seconds and 󽗊ash again for 3 times
at tenth seconds. The indicator will keep 󽗊ashing when the device is
returned to default factory setting.
Identify: Press and hold the reset button for three seconds until the
LED indicator 󽗊ashes for 3 times. The LED indicator will keep 󽗊ashing
and the identify mode will last for one min.
LED indicator
Reset button

7
4.1 To get started, you will need:
• A Zigbee Gateway.
• A mobile phone with a mobile APP installed.
4.2 Adding to the gateway's network
1. Set your gateway to permit joining (see your gateway's manual).
2. Power on the smart relay module and make sure the LED indicator
is 󽗊ashing (If not, reset it to factory defaults).
3. Make sure the smart relay module is in the range of gateway’s
network. After few seconds the the smart relay module will join the
gateway automatically and the LED indicator will become steady when
successfully joined.
4.Now you are able to control the smart relay module using the mobile
app.
Note: If the adding is failed, simply reset the smart relay module and
retry.
5FAQ
Q 1. Can I control this relay module using a wireless switch?
Yes. You could use a ZigBee wireless switch such as SLC602 wireless
switch to control it rather than using the mobile app. You can refer to
SLC602 guide to pair with it.
Con󽗉gure Network
4