PVI Industries TEMPTRAC User manual

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 1 of 30 PV7069-T 03/17
Part number 129209
Installation and interface must be performed by a qualified controls technician.
IMPORTANT: THIS MANUAL CONTAINS INFORMATION REQUIRED FOR INSTALLATION, INTERFACE AND
CONFIGURATION OF THIS EQUIPMENT. READ AND FOLLOW THE INFORMATION IN THIS MANUAL AND ALL
OTHER PROVIDED INSTRUCTIONS, LABELS AND MARKINGS BEFORE INSTALLING, OPERATING OR SERVICING
THIS UNIT.
Contents
OVERVIEW OF INTERFACE METHODS:.................................................................................................2
TEMPTRAC PROTOCOL ...........................................................................................................................4
ITEMS REQUIRED FOR GATEWAYINTERFACE:...................................................................................4
ITEMS REQUIRED FOR MODBUS DIRECT INTERACE:.........................................................................4
IDENTIFY EQUIPMENT:.............................................................................................................................5
WIRING BAS TO GATEWAY AND THEN GATEWAY TO TEMPTRAC:..................................................6
WIRING OF TEMPTRAC TO BAS (Direct, no Gateway):...........................................................................7
GATEWAY CONFIGURATION CONNECTION:........................................................................................7
CONFIGURE GATEWAY DIP SWITCHES:...............................................................................................8
CONFIGURE THE GATEWAY USING THE HTML INTERFACE:.............................................................9
CONFIRM OPERATION:...........................................................................................................................10
TROUBLESHOOTING GATEWAY:..........................................................................................................10
HOOKUP OVERVIEW:..............................................................................................................................11
APPLICATION SPECIFICS:......................................................................................................................12
POINTS LIST:............................................................................................................................................16
TYPICAL POINTS:.....................................................................................................................................16
ALL POINTS INCLUDING ADVANCED:...................................................................................................18
ADVANCED MODBUS LIST:....................................................................................................................25
TO THE INSTALLER / CONTROLS INTEGRATOR: After installation and integration, these instructions must be
given to the equipment user or left near the appliance.
SPECIAL INSTRUCTIONS TO THE OWNER: Retain this manual for future reference. These instructions contain
important integration information that will help you in maintainingand operatingthis appliance.
PVI INDUSTRIES, LLC - Fort Worth, Texas 76111 - Web www.pvi.com - Phone [phone]

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 2 of 30 PV7069-T 03/17
Part number 129209
OVERVIEW OF INTERFACE METHODS:
This document is a quick reference for connecting the TempTrac water heater / boiler control to a Building
Automation System (BAS). Direct connection via MODBUS RTU or using a gateway to interface to
protocols other than MODBUS RTU are the methods covered in this manual.
BAS to Heaters direct, using MODBUS RTU:
Building Automation System (BAS) connecting directly to water heaters using MODBUS RTU twisted pair
wire. (Wiring is RS-485 physical layer.)
BAS to heaters using a Protocol Gateway:
Building Automation System (BAS) connecting to a PVI gateway. This can provide interface to BACNET
MSTP, BACNET IP, LONWORKS, and MODBUS TCP.
(Wiring from gateway to heaters is RS-485 physical layer. Wiring from BAS to gateway will depend on
Protocol.)
BAS to heaters using discrete connections:
This is simply control of the heater using the external ENABLE/DISABLE contacts, remote equipment
contacts and the alarm contacts. See wiring diagram of equipmentfor details.
Other equipment
GATEWAY
PVI WATER HEATERS
BAS
Other equipment
PVI WATER HEATERS
BAS

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 3 of 30 PV7069-T 03/17
Part number 129209
TempTrac Heater MODBUS fixed settings:
Most of theMODBUS RTU and Port settings are not adjustable
Baud Rate: 9600bps (Not adjustable)
Data Length: 8 bit (Not adjustable)
Parity: None (Not adjustable)
Stop Bits: 1 (Not adjustable)
Start/Stop: Silent interval of 3 characters minimum
Minimum Time Between Retry: 500 msec.
Maximum read command is 5 words
Steps to change the TempTrac MODBUS address:
Editing parameters should be done without any device trying to communicate through the MODBUS port.
To avoid interference from a gateway or BAS, you should unplug the MODBUS adapter port on the back
of the TempTrac atthe white header, while making changes tothe TempTrac parameters.
The first step tointerfacing with a TempTrac or group of TempTracs will be the assignment of theaddress
number for each boiler. The default for TempTrac is Address #1. You can assign any number in the range
of 1-247. This is the limitations of the MODBUS RTU standard.
The MODBUS address is the Adr parameter, and it is in the Pr2 menu.
Enter the Programming mode by pressing the SET and DOWN key for more than 3 seconds. (Lead with
the SET key.)
Pressing the DOWN key, parameters will display in top, and value in bottom.
Select Pr2 / PAS (parameter / value), and press the SET key.
The lower display will show the value 0 --with a flashing zero.
Use UP or DOWN keys to inputthe security code in the flashing digit; confirm
each digit by pressing SET. The security code is 321.
After hitting SET on the last digit, you will be in the Pr2 menu.
Once you have entered the Pr2 menu press the DOWN key to move through
the parameters until the Adr parameter appears on the top display.
Now press the SET key once and the value number will begin to blink. Use
the arrow key to set the address and then hit the SET key.
After hitting the SET, it will automatically go to the next parameter. Let it time
out, or cycle power to the TempTrac.
Each TempTrac on a RS-485 network must have a unique MODBUS
address.
The TempTrac MODBUS adapter port:
The MODBUS adapter is an orange dongle with 2green screw terminals attached to an 8 inch cable that
plugs intothe back of the TempTrac at a white header. This can be an option installed on heater, or it may
be a separate line item part.When the option is available, it is MBUSC option code. As a standalone part,
it is PN: 11807.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 4 of 30 PV7069-T 03/17
Part number 129209
TEMPTRAC PROTOCOL
The MODBUS RTU protocol is well established industry protocol and technical references for this are
readily available on the Internet.
Data Types Used
The TempTrac only uses one data type
Holding Registers (40001 –49999) Read/Write
Other data types such as Coils are not implemented in the TempTrac control.
Only the data points in the POINTS LIST should beaccessed.
Physical Layer RS-485
MODBUS RTU uses the physical layer RS-485.
RS-485(EIA-485):A2wire(twistedpair)multidropnetwork.Eachdevicecansenddatabyholdingpositive
and negative voltage on the line and reversing polarity on the 2 wires. When no devices are transmitting,
the line will be tristate. The recommended arrangement of the wires is as a connected series of point-to-
point (multi-dropped) nodes, i.e. a line or bus, not a star, ring, or multiply connected network. The number
of devicesthat can be connected to a singleline is defined inthe RS-485standard by the input impedance
of 32UNITLOADs.Thewireandcircuitsinterfacing onthis2wireconnectionisconsideredthePHYSICAL
LAYER. (RS-485 is the same physical layer as used with BACNET MSTP.)
No provisions for biasing resistors or termination resistors are provided on the control. If required, this will
need to be provided externally.
The PVI gatewaydoesprovideoptionalbiasing(default)andcanprovideaterminationresistor,ifrequired.
ITEMS REQUIRED FOR GATEWAY INTERFACE:
One or more water heaters with a TempTrac control (red/orange LED display with 6 tactile buttons)
including the RS-485 adapter.
Protonode Gateway with Power supply adapter (when ordering, please specify what protocol is required;
BACNET MSTP, BACNET IP, LONWORKS or MODBUS TCP).
Protonode Gateway Manual (Coversgeneral information for the gateway).
PV7069-T.PDF Interface manual that covers specifics for interfacing with the TempTrac system. Also
includes the points list for the TempTrac control system. (This document).
120VAC power outlet for the power supply.
Computer with web browser and Ethernetconnectioncapability toconfiguregateway.
ITEMS REQUIRED FOR MODBUS DIRECT INTERACE:
One or more water heaters with a TempTrac control (red/orange LED display with 6 tactile buttons)
including the RS-485 adapter.
PV7069-T.PDF Interface manual that covers specifics for interfacing with the TempTrac system. Also
includes the points list for the TempTrac control system.(This document).

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 5 of 30 PV7069-T 03/17
Part number 129209
IDENTIFY EQUIPMENT:
The equipment should have a TempTrac mounted on the control panel. The RS-485 adapter may be
installed or may ship lose. The gateway and power supply ship lose. The gateway is a grey module that
has a wall wart style power supply.
TempTrac is mounted on the control panel of the equipment. On the back side of the TempTrac is a white
header. The RS-485 adapter plugs into this with a 8 inch cable. The orange adapter has 2 green terminals
labeled (+) & (-).
The Protocol Gateway, if supplied, comes with a power supply and ships as a loose item.
Protocol Gateway
TempTrac Front and
side view
TempTrac back,
showing adapter
dongle.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 6 of 30 PV7069-T 03/17
Part number 129209
WIRING BAS TO GATEWAY AND THEN GATEWAY TO TEMPTRAC:
Each gateway has 3 connection points.
The 6 position terminal block contains connection for power and MODBUS RTU (going to heaters).
The Ethernet port is for configuration, BACNET IP, or MODBUS TCP.
The 3 or 2 pin terminal is for the BAS interface: BACNET MSTP, or LONWORKS.
Power Connection:
Gateway power supply, 6 position terminal +PWR, -PWR.
Use supplied wall wart style power supply. 15VDC. Do not power other devices with same power supply.
If power adapter has not already been connected, cut and discard the connector on the end, strip and
terminate the power adapter in the proper terminals. Verify polarity. If another supply is to be used, it must
be isolated. Do not use 24VAC power from heater.
Gateway Connection to Heaters:
Wiring from Gateway to the heaters, use twisted pair wire.
Connector on the orange dongle adapter that is on the end of a 8” cable plugged into the back of the
TempTrac.
The wiring is standard 2 wire RS-485 wiring. You will connect all devices together in a daisy chain. We
recommend the gateway to be at the start of this connection.
Gateway
6 Pos. terminal
TempTrac
Orange adapter
TempTrac #2
Orange adapter
Tx/+
(+)
(+)
Rx/-
(-)
(-)
GND
Building Automation Connection:
BAS protocol
Connection Port on Gateway
Labeled
BACNET MSTP
3 TERMINAL CONNECTOR
FIELD
BACNET IP
ETHERNET PORT
ETHERNET
LONWORKS
2 TERMINAL CONNECTOR
LonWorks
MODBUS TCP
ETHERNET PORT
ETHERNET

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 7 of 30 PV7069-T 03/17
Part number 129209
WIRING OF TEMPTRAC TO BAS (Direct, no Gateway):
The back side of the TempTrac has a white header with an 8 inch cable, connecting to an orange adapter
module with 2 green terminals labeled (+) & (-). This is the RS-485 Modbus connection point.
Field connection
for BAS
TempTrac
Orange adapter
TempTrac #2
Orange adapter
Testing
VDC
Results for proper
hookup
RS 485 +
(+)
(+)
Positive
lead
+ 0.100
To
+ 5.500
RS R85 -
(-)
(-)
Negative
lead
GND
Ensure the proper polarity, check with a Digital Volt Meter set to Volts DC. Take a reading at the orange
adapter from the (-) Terminal to the (+) Terminal.The (+) should be the positive lead when connected.
GATEWAY CONFIGURATION CONNECTION:
Both the LONWORKS and BACNET gateway have an Ethernetport. Connect the computer using a patch
cable or cross-over cable to establish a direct connection to the gateway. Older units may require a cross-
over cable or two patch cables with an Ethernet switch. If using BACNET IP or MODBUS TCP interface,
connect the BAS Ethernet cable to the gateway when configuration is complete.
At this point, each heater and the gateway should all be powered, and have all wiring finished. The RUN
LED will toggle every second to indicate the gateway is running.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 8 of 30 PV7069-T 03/17
Part number 129209
CONFIGURE GATEWAY DIP SWITCHES:
The ON position is toward the center of the module, and OFF is toward the edge of the module. Only the
BACNET gateway requires dip switch settings. The BACNET gateway is used for MODBUS TPC also.
DIP SWITCHES S0-3 PROTOCOL
Set Protocol (BACNET and MODBUS gateway only):
The gateway protocol is determined on power up by looking at
the “S” dip switches.
If the protocol is changed, the configuration/profiles must be
clearedandreconfigured.ThisisdonewiththeHTMLinterface.
MODBUS RTU does not require a gateway.
LONWORKS: Configured in hardware, no need to adjust dip
switches.
DIP SWITCHES B0-4 BAUD
3PIN CONNECTOR TO BAS, Configure BAUD:
Default is 38400.
Configures the Baud rate for the 3 position terminal block.
This is the connection that will connect to the Building Automation
System (BAS).
This is usedonly when the protocol is BACNET MSTP.
A0-7 (BACNET MSTP) MAC ADDRESS:
Default is MAC address 3.
Configure the MAC address for
the BACNET Gateway by
summing the “A” dip switches
that are ON.
MAC address range: 1 –127
Protocol
S0
S1
S2
S3
BACNET IP
OFF
OFF
OFF
OFF
BACNET MSTP
ON
OFF
OFF
OFF
MODBUS TCP
OFF
ON
OFF
OFF
MODBUS RTU
ON
ON
OFF
OFF
Baud
B0
B1
B2
B3
9600
ON
ON
ON
OFF
19200
OFF
OFF
OFF
ON
38400 *
ON
ON
OFF
ON
57600
OFF
OFF
ON
ON
76800
ON
OFF
ON
ON
1
2
4
8
16
32
64
<-sum for address
A0
A1
A2
A3
A4
A5
A6
A7
Address
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
0
Invalid
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
2
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
3 *
Default
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
4
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
5
OFF
ON
ON
OFF
OFF
OFF
OFF
OFF
6
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
7
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
8
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
9
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
10
…
…
…
…
…
…
…
…
…
ON
ON
ON
ON
ON
ON
ON
OFF
127

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 9 of 30 PV7069-T 03/17
Part number 129209
CONFIGURE THE GATEWAY USING THE HTML INTERFACE:
ThissectionwillprovidetheparametersrequiredfortheTempTraccontrol.Formoredetailsofthegateway,
consult the gateway manual. Connect your computer’s Ethernet port to the Ethernet port of the gateway.
Using aweb browser, browseto thegateway at IP address: 192.168.1.24 default (Ifyou have changedthe
IP address,go to the appropriate address.).
If the device IP address has been changed and is not known, a utility is available from Feildserver.com.
Contact Fieldserver for more information.
Menu options vary depending on if you are configuring a LONWORKS gateway, BACNET Gateway set
for BACNET IP, a BACNET gateway set for BACNET MSTP, or a BACNET gateway set for MODBUS
TCP.
Using your browser, set the following and SUBMIT after each change.
MODBUS RTU Baud Rate: 9600
MODBUS RTU Parity: NONE
MODBUS RTU Data Bits: 8
MODBUS RTU Stop Bits: 1
(BACNET options)
BACNET Network Number: Must be unique network number on BACNET network
BACNET Node Offset: This will be used to create the DEVICE INSTANCE. Sum the device
MODBUS Address and this number. Example 50000 Node Offset+ MODBUS address 1 = 50001
Device Instance. Each MODBUS device will have its own Device Instance number.
(BACNET MSTP option)
BACNET MSTP Max Master: 127
(BACNET IP option)
BACNET IP Port: 47808 (Default)
BACNET COV: COV Disable
(BACNET MSTP option)
BACNET BBMD: - (Default “-“, enabling this is an advanced feature, not recommended)
BACNET Router: NO for 1 water heater, YES for multiple water heaters
SELECT THE DEVICE TYPE (BACNET & LONWORKS):
Press the ADD button, under Node ID enter the MODBUS address of the first heater. Typically you will
have the nearest heater setup as MODBUS address 1, and the next heater MODBUS address 2. All
heaters ship from factory with MODBUS Address set to 1. Each heater must have a unique MODBUS
address. (See previous section Setup heater MODBUS address)
Under Current profile, select the proper interface for the TempTrac control.
For BACNET Gateway: Select
BAC_IP Temptrac for BACNET IP
BAC_MSTP Temptrac for BACNET MSTP
For LONWORKS Gateway: Select LON TempTrac Water Heater
Press the Submit button.
Add additional devices as required.
After adding all devices, restart the gateway by clicking the SYSTEM RESTART button.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 10 of 30 PV7069-T 03/17
Part number 129209
CONFIRM OPERATION:
Heater Communication:
Communication between gateway and heaters is evident by rapid flashing of the TX and RX LEDs on the
gateway. If only the TX is flashing (may be as slow as 30 seconds between flashes), that will indicate no
response from the heaters.
Building Automation System Communication:
Usingthe HTML interface,you can confirmsome operations and under USERMESSAGES, confirm there
areno errorsmessages. At this point, the BAS will need to discover the gateway and implement the points
into its integration.
TROUBLESHOOTING GATEWAY:
ERR Red LED on
oGateway is reporting an error.
oConnect togateway with HTML interface to view error messages
PWR LED not on
oConfirm power on +PWR and –PWR
TX & RX not flashing
oConfirm connections to heaters and MODBUS addressing
oConfirm gateway has been configured
TX flashing, RX not flashing
oGateway is talking toTempTrac, but not getting responsefrom TempTrac. Confirm wiring,
confirm TempTrac is configured to proper address,Baud, Parity, Stop bits.
Verify polarity of all connections:
Set a Digital Volt Meter to read DC Volts. (Capable of reading less than 1.0VDC)
Pos. (red)
Probe
Neg. (black)
Probe
Min
Max
Actual
Reading
Gateway 6 pin terminal block
+PWR
-PWR
+9.0VDC
+30VDC
Tx/+
Rx/-
+0.1VDC
+5.5VDC
Gateway 3 pin terminal block (BACNET MSTP only)
RS 485 +
RS 485 -
+0.1VDC
+5.5VDC
TempTrac orange dongle (Each heater)
(+)
(-)
+0.1VDC
+5.5VDC
(+)
(-)
+0.1VDC
+5.5VDC
(+)
(-)
+0.1VDC
+5.5VDC
(+)
(-)
+0.1VDC
+5.5VDC
(+)
(-)
+0.1VDC
+5.5VDC
For advance gateway troubleshooting, reference the gateway manual.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 11 of 30 PV7069-T 03/17
Part number 129209
HOOKUP OVERVIEW:
BACNET MSTP or LONWORKS
BACNET IP or MODBUS TCP
MODBUS RTU Direct Connect
BACNET MSTP
OR
LONWORKS
To heaters with
TempTrac
Power Adapter
BACNET IP
OR
MODBUS TCP
To heaters with
TempTrac
Power Adapter
MODBUS RTU
To heaters with
TempTrac

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 12 of 30 PV7069-T 03/17
Part number 129209
APPLICATION SPECIFICS:
EachproductthatusestheTempTraccontrolmayhavesubtledifferences.Thefollowingproductsaddress
the important information regarding each device.
Conquest 100 Gallon (199 – 299) & 130 gallon 399: (Smaller Conquest)
Model Numbers: 20 L 100A-GCL, 25 L 100A-GCL, 30 L 100A-GCL, 40 L 130A-GCL
Probe 1: Is in the top of the tank, and controls the burner
Probe 2: Is in the mid-section and controls the agitator pump using Relay3
Probe 3: Is in the flue
Alarm_AL2: Alarm on any failure
Burner_Relay1: Burner
Relay2: Alarm dry contact
Relay3: Agitator pump
Discrete connections:
External Enable: Terminals R1 –R2, Jumper to enable. Heater ships with jumper on this. An external
enable/disable can be attached to this. This is a low current, low voltage contact. It is advised to use a
contact with gold plating. If not available, use 2 contacts in parallel.
Alarm: A1 & A2 (Output from Heater) Closed = ALARM.
Remote Proving: C1 & C2. Ships with factory jumper. Open will prevent burner from operating. Keeping
this open will create alockout condition that will require user intervention.
Remote Equipment/ Burner ON: ContactthatwillcloseP1–P2duringa heatingcycle.Open,theheater
is not calling for heat.
No Setpoint Input: There is not a discreet methodto send a setpoint signal to the Conquest.
Conquest 130 Gallon (500 – 800): (Larger Modulating Conquest)
Model Numbers: 50 L 130A-GCML, 60 L 130A-GCML, 70 L 130A-GCML, 80 L 130A-GCML
Same asthe smaller Conquest with the addition of modulation.
Modulation Rate: Modulation rate, Low fire = 0, High Fire = 100
Discrete connections:
Same as the smaller Conquest with the following notes:
No Modulation Input: There is not discreet way for a building automation system to control
the modulation (firing rate) of the Conquest.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 13 of 30 PV7069-T 03/17
Part number 129209
Centauri Boiler, Centauri Plus Boiler, VT3 Boiler:
Model Numbers: All Centauri, Centauri Plusand VT3Boilers
Probe 1: This temperature is displayed in yellowin the lower section of the display.
WithSSBCOoption,thisprobeislocatedinthetopoftheboiler.Withoutthisoption,
theprobeisshippeduninstalledandshouldbeinstalled inthe BHWRpipingtoread
the temperature of the water entering the boiler.
Probe 2: This temperature is displayed in red in the upper section of the display.
WithSSBCOoption,thisprobeisshippeduninstalledandisintendedtobeinstalled
in the field in the boiler’s HWR piping. Without the SSBCO option, this probe is
installed in the top of the boiler providing the outlet water temperature.
Probe 3: Is an Auxiliary probe that can be used for outdoor temperature or other
temperature readings. This is optional and not standard.
Alarm_AL3: Alarm on any failure
Burner_Relay1: Burner
Relay2: Not used
Relay3: Isolation Valve control when the OnTrac boiler management system is controlling.
Modulation Rate: Modulation rate, Low fire = 0, High Fire = 100
Discrete connections:
Ext Enable: Terminals R1 –R2, Jumper to enable. Heater ships with jumper on this. An external
enable/disable can be attached to this. (Recommend relay at boiler, min 10A at 24VAC.)
Remote Equipment: P1 & P2, this is a contact that is driven any time a call for heat is present. Note this
is only provided if the Remote Equipment or Louver options are present.
Alarm: A1 & A2 provide a 3 min alarm signal that is present after a failure to ignite burner for 4 minutes.
This output will be active for 3 minute and then the communication alarm will become active dropping the
call for heat and dropping this signal. It is possible to get this alarm and the alarm condition that caused
this alarm can be corrected before the 3 minutes, removing the alarm and not having a lockout or alarm
condition over communication. (3min signal of alarm condition and potential lockout.)

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 14 of 30 PV7069-T 03/17
Part number 129209
M3 Boiler
Probe 1: Isinthe topofthe tank,andcontrolsthe burner. Providesoutlettemperature.
Probe 2: Is wired but lose and field installed in the boiler HWR piping.
Probe 3: Is in the flue.
Alarm_AL2: Alarm on any failure.
Burner_Relay1: Burner
Relay2: Alarm dry contact, goes to terminals A1 & A2.
Relay3: Isolation Valve control, used with OnTrac group control. Terminals labeled
CIRCULATOR 1 & 2.
Modulation Rate: Modulation rate, Low fire = 0, High Fire = 100.
Discrete connections:
External Enable: Terminals R1 –R2, Jumper to enable. Heater ships with jumper on
this. An external enable/disable can be attached to this. This is a low current, low
voltage contact. It is advised to use a contact with gold plating. If not available, use 2
contacts in parallel.
Alarm: A1 & A2 (Output from Heater) Closed = ALARM.
Remote Proving: C1 & C2. Ships with factory jumper. Open will prevent burner from operating. Keeping
this open will create alockout condition that will require user intervention.
Remote Equipment/ Burner ON:ContactthatwillcloseP1–P2duringa heatingcycle.Open,theheater
is not calling for heat.
No Setpoint Input: There is not a discreet methodto send a setpoint signal to the M3 boiler.
NoModulationInput:Thereisnotdiscreet wayforabuildingautomationsystemtocontrolthemodulation
(firing rate) of the Conquest.
Quickdraw Steam to Water Storage
Probe 1: Lower Sensor
Probe 2: Upper Sensor
Relay1: Control valve
Reference wiring diagram for more details. Options vary greatly on this product.
Discrete connections:
External Enable: Terminals
Remote Equipment / Heating: E1 & E2 terminals are closed when heating, and open when not. This is
an option REMEQ.
Alarm: A1 & A2 terminals are closed when in Alarm.This is an option REMAL.
Quickdraw Steam to Water Instantaneous
Probe 1: Lower Sensor
Probe 2: Upper Sensor
Relay1: Control valve
Reference wiring diagram for more details. Options may vary on this product.
Discrete connections:
External Enable: Terminals
Remote Equipment / Heating: E1 & E2 terminals are closed when heating, and open when not. This is
an option REMEQ.
Alarm: A1 & A2 terminals are closed when in Alarm.This is an option REMAL.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 15 of 30 PV7069-T 03/17
Part number 129209
Other Equipment and Equipment Custom features:
Reference supplied wiring diagram and the I & O Manual. Contact PVI for additional information.
Below is a list of other products that can usethe TempTrac controller:
QuickdrawWater to water Storage
EZ PLATE STORAGE
TURBOPOWER 99
TURBOPOWER
POWER VT PLUS
TRICON
MAXIM 3
DURAWATT (With TTRAC option)
MAXIM (With TTRAC option)
COBREX STORAGE

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 16 of 30 PV7069-T 03/17
Part number 129209
POINTS LIST:
The gateway will provide a full points list, including typical points and advanced points. Normal interface
willonlyrequiretheTYPICALPOINTS.ManypointsareprovidedasADVANCEDPOINTSandnotadvised
to be used in normal integration. The Advanced Points are present for the purpose of future development
and custom applications. Please consultfactoryif any points not in the TYPICAL POINTS are required.
Key:
LONWORKS shows multiple devices connected with adevice number suffix, (#) represent the device.
MODBUS address with “:” to designate single bit usage of register. Number following colon represents bit
location, 0is the least significant bit.
Point Name
Read/Write
Short Description
MODBUS
Register Type
Address Offset
MODBUS Address
BACNET
BACNET Name
Object Instance
BACNET Units
LONWORKS
Lon Read name_#
Lon Write name_#
Lon Units
NOTES
TYPICAL POINTS:
The points that are typically used to interface with the heater. Most integrations only require points from
this list.
TYPICAL POINTS:
Control_CNT
Write
Enable Heater 257=on 1 = off
MODBUS
Holding Register
1280
41281
BACNET
Enable
128100
LONWORKS
nvoCtrl_CNT_#
This can be used to prevent the heater from heating via communication. 257 or 0X0101 = on, 1 or 0x0000 = off
The resister cannot be read. The register should only be written to with the values 257 and 1, as it has other
undocumented functions.
Setpoint_St1
Read/Write
System Setpoint
MODBUS
Holding Register
768
40769
BACNET
Setpoint_St1
76900
Deg-F
LONWORKS
nvoSP_St1_#
nviSP_St1_#
Deg_F
This is the setpoint for the heater.
Probe 1
Read Only
Controlling Probe Degrees F
MODBUS
Holding Register
256
40257
BACNET
Probe1
25700
Deg-F
LONWORKS
nvoProbe1_#
Deg_F
Probe that provides control of heating. Location can vary depending on equipment and application. See section
that discussed the various equipment to determine actual location of probe. Connection on TempTrac is green
screwterminals 14 and common 17.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 17 of 30 PV7069-T 03/17
Part number 129209
TYPICAL POINTS:
Probe 2
Read Only
Probe 2 in degrees F
MODBUS
Holding Register
258
40259
BACNET
Probe2
25900
Deg-F
LONWORKS
nvoProbe2_#
Deg_F
Optional probe on some devices, usually installed on mostdevices. If installed and enabled, returns the
temperature of the probe in degrees F. Connection on TempTrac is green screw terminals 15 and common 17.
Probe 3
Read Only
Probe 3 in degrees F
MODBUS
Holding Register
260
40261
BACNET
Probe3
26100
Deg-F
LONWORKS
nvoProbe3_#
Deg_F
Optional probe on somedevices, not usually installed on most devices. If installed and enabled, returns the
temperature of the probe in degrees F. Connection on TempTrac is green screwterminals 16 and common 17.
Burner Runtime
Read/Write
Burner Runtime Hours 0-65535
MODBUS
Holding Register
848
40849
BACNET
BURNER_HOURS_ou1
84900
Hours
LONWORKS
nvoBrnHr_ou1_ #
nviBrnHr_ou1_#
Hours
NOTE: Number of hours the burner has been enabled. Once it reaches 9999. This can be written to, as a way
to reset it.
Modulation Rate
Read Only
Monitor the modulation signal
MODBUS
Holding Register
262
40263
BACNET
Modulation_FR
26300
LONWORKS
nvoMod_FR_#
Modulation rate on the analog output 4-20ma is represented as 0-100. This feature was introduced inFirmware
0.5 (5) and is not available from older TempTrac modules already in the field.
Burner_Relay1
Read Only
Status of burner, Relay1 (Output 1)
MODBUS
Holding Register
2049
42050:0
BACNET
Burner_Relay1
205050
LONWORKS
nvoBrn_Rel1_#
This is Bit 0 of the Relay status word. It is the relay that controls the main heating output. Typically the Burner
Status. BACNET and LONWORKS have this broke out into state logic points. MODBUS, you will have to break
it out yourself. Read value, BITWISE AND with 0x0001, if result = 0, relay is off. If result = 1, relay is on.
Alarm_AL2
Read Only
Status of digital input #2 Alarm
MODBUS
Holding Register
3328
43329:11
BACNET
Alarm_AL2
332961
LONWORKS
nvoAlarm_AL2_#
Digital Input #2 alarm. Onsomeproducts, this is a general failure to operate alarm. See product specific
information. This is Bit 11 of the ALARM STATUS ALL word. Flashes ‘AL2’ or ‘LP’ on TempTrac display. In
BACNET and LONWORKS, this is broken out into a state logic point.
For MODBUS ALARMS && 0x0800 = 0x0800 Alarm is active. = 0x0000 Alarm is not active.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 18 of 30 PV7069-T 03/17
Part number 129209
TYPICAL POINTS:
Alarm_AL3
Read Only
Status of digital input #3 Alarm
MODBUS
Holding Register
3328
43329:12
BACNET
Alarm_AL3
332962
LONWORKS
nvoAlarm_AL3_#
Digital Input #3 alarm. Onsomeproducts, this is a general failure to operate alarm. See product specific
information. This is Bit 12 of the ALARM STATUS ALL word. Flashes ‘AL3’ or ‘HP’ on TempTrac display. In
BACNET and LONWORKS, this is broken out into a state logic point.
For MODBUS ALARMS && 0x1000 = 0x1000 Alarm is active. = 0x0000 Alarm is not active.
Com Status
Read Only
Communication Status bit
MODBUS
Input Register
NA
NA
BACNET
Gateway_TT_Com_OK
200
LONWORKS
nvoGwyTTCmOK_#
NOTE: This point is notgenerated by the heater; itis generated internally bythegateway. It is astatus of the
communication connection between the gateway and the heater. If active (GOOD), the gateway is talking to the
heater. If inactive (NOT_PRESENT) then the gateway does not have good communication with the heater. This
point may take up to 3 minutes to register properly after communication is established or interrupted. If this
value if reading NOT_PRESENT, then no all over values are suspect, as the device is not communicating.
Generally the Gateway will hold the last value received. The only way to ensure you have the current values
from the heater is to verify this pointis ACTIVE as well.
ALL POINTS INCLUDING ADVANCED:
Points listed below that are not in the TYPICAL POINTS are provided for advanced interface and for
custom applications. Contact factoryfor additional information.
ALL POINTS INCLUDING ADVANCE:
Control_CNT
Write
Enable Heater 257=on 1 = off
MODBUS
Holding Register
1280
41281
BACNET
Enable
128100
LONWORKS
nvoCtrl_CNT_#
This can be used to prevent the heater from heating via communication. 257 or 0X0101 = on, 1 or 0x0000 = off
The resister cannot be read. The register should only be written to with the values 257 and 1, as it has other
undocumented functions.
Setpoint_St1
Read/Write
System Setpoint
MODBUS
Holding Register
768
40769
BACNET
Setpoint_St1
76900
Deg-F
LONWORKS
nvoSP_St1_#
nviSP_St1_#
Deg_F
This is the setpoint for the heater.
Setpoint_St1 C
Read/Write
System Setpoint
MODBUS
BACNET
Setpoint_St1_C
76900
Deg-C
LONWORKS
Special BACNET point that converts the Setpoint value to degrees C in the gateway. Not available in
LONWORKS or MODBUS.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 19 of 30 PV7069-T 03/17
Part number 129209
ALL POINTS INCLUDING ADVANCE:
Hy1
Read
Setpoint Differential
MODBUS
Holding Register
772
40773
BACNET
Hy1
77300
delta-degrees-Fahrenheit
LONWORKS
nvoHy1_#
Differential. (if Hy1 is negative) The heater will begin heating when Probe #1 must fall this far below St1
setpoint, and stay on until the heater reaches St1 setpoint.
(If Hy1 is positive) The heater willcome on when Probe #1 falls to or below St1 setpoint, and will not turn off
until it has reached this far above St1 Setpoint. BACNET and LONWORKS, this point is configuredas aread
only, with MODBUS, there is no protection from changing this value.
St4
Read Only
Modulation Start
MODBUS
Holding Register
792
40793
BACNET
St4
79300
No Units
LONWORKS
nvoSt4_#
Starting point of modulation. Related to the St1 setpoint. If Probe 1 is above St1 + St4, then Modulation signal
will be low fire. If Probe 1 falls below(St1 + St4) then the analog output signal will modulate based on the setting
in the SR register. This is set to No Units in BACNET because it can relative to St1 or is can be independent
value. Typicallyit is configured as relative to St1. BACNET and LONWORKS, this point is configured as a read
only, with MODBUS, there is no protection from changing this value.
SR
Read
Modulation bandwidth
MODBUS
Holding Register
793
40794
BACNET
SR
79400
delta-degrees-Fahrenheit
LONWORKS
nvoSR_#
Normally this is a negative number. Number of degrees of change in Probe 1 that will modulate from 0 to 100%.
St1 + St4 = low fire, St1 + St4 + SR =High Fire. Temperatures above low fire will be low fire, temperatures
below high fire will be high fire. In-between, the output will modulate from 4-20mA (0-100%) BACNET and
LONWORKS, this point is configured as a read only, with MODBUS, there is no protection from changing this
value.
Probe 1
Read Only
Controlling Probe Degrees F
MODBUS
Holding Register
256
40257
BACNET
Probe1
25700
Deg-F
LONWORKS
nvoProbe1_#
Deg_F
Probe that provides control of heating. Location can vary depending on equipment and application. See section
that discussed the various equipment to determine actual location of probe. Connection on TempTrac is green
screwterminals 14 and common 17.
Probe 2
Read Only
Probe 2 in degrees F
MODBUS
Holding Register
258
40259
BACNET
Probe2
25900
Deg-F
LONWORKS
nvoProbe2_#
Deg_F
Optional probe on some devices, usually installed on mostdevices. If installed and enabled, returns the
temperature of the probe in degrees F. Connection on TempTrac is green screwterminals 15 and common 17.
Probe 3
Read Only
Probe 3 in degrees F
MODBUS
Holding Register
260
40261
BACNET
Probe3
26100
Deg-F
LONWORKS
nvoProbe3_#
Deg_F
Optional probe on somedevices, not usually installed on most devices. If installed and enabled, returns the
temperature of the probe in degrees F. Connection on TempTrac is green screwterminals 16 and common 17.

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST
Page 20 of 30 PV7069-T 03/17
Part number 129209
ALL POINTS INCLUDING ADVANCE:
Probe 1 C
Read Only
Controlling Probe Degrees C
MODBUS
BACNET
Probe1_C
25790
Deg-C
LONWORKS
Special BACNET point that converts the Probe value to degrees C in the gateway. Not available in
LONWORKS or MODBUS.
Probe 2 C
Read Only
Probe 2 in degrees C
MODBUS
BACNET
Probe2_C
25990
Deg-C
LONWORKS
Special BACNET point that converts the Probe value to degrees C in the gateway. Not available in
LONWORKS or MODBUS.
Probe 3 C
Read Only
Probe 3 in degrees C
MODBUS
BACNET
Probe3_C
26190
Deg-C
LONWORKS
Special BACNET point that converts the Probe value to degrees C in the gateway. Not available in
LONWORKS or MODBUS.
Manual Modulation
Read/Write
Forcemodulation to a level
MODBUS
Holding Register
797
40798
BACNET
PS4
79800
LONWORKS
NvoPS4_#
NviPS4_#
Used to force amodulation rate. Typically used by service tech to make combustion adjustments at a particular
firing rate. Normal setting is 101 = Auto. This allows the heater to modulate ad the load requires. If you put a
value 0-100, it willforce the heater to that firing rate when operating. 0=Low Fire, 100=High Fire
Use with caution. Advise allowing the heater do control its own modulation.
ALL
Read/Write
Minimum Temperature Alarm
MODBUS
Holding Register
814
40815
BACNET
ALL
81500
Deg-F
LONWORKS
nvoALL_#
nviALL_#
Deg_F
Minimum temperature for Probe 1. Alarm will be activated if Probe 1 falls below this temperature. See Alarm
points.
ALU
Read/Write
Flame Current for proof of flame
MODBUS
Holding Register
815
40816
BACNET
ALU
81600
Deg-F
LONWORKS
nvoALU_#
nviALU_#
Deg_F
Maximum temperature for Probe 1. Alarm will be activated if Probe 1 rises above this temperature. See Alarm
points.
Burner Runtime
Read/Write
Burner Runtime Hours 0-65535
MODBUS
Holding Register
848
40849
BACNET
BURNER_HOURS_ou1
84900
Hours
LONWORKS
nvoBrnHr_ou1_ #
nviBrnHr_ou1_#
Hours
NOTE: Number of hours the burner has been enabled. Once it reaches 9999. This can be written to, as a way
to reset it.