PVI PV 6150b User manual

PV 6150b 2/02 1
SPECIFICATION FOR DOMESTIC WATER HEATERS
Condensing, Gas-Fired Water Heaters with Polymer-Lined Storage Tanks
Furnish and install the following POWER VT® gas water heater(s) as manufactured by PVI INDUSTRIES, INC of Fort
Worth, Texas.
Model Btu/h GPH Recovery Storage
Qty Number Input 40° to _____°F Tank
___ ____________ __________ ________ _______ gallons
___ ____________ __________ ________ _______ gallons
___ ____________ __________ ________ _______ gallons
Efficiency
The water heater will operate at a thermal efficiency of 94% when tested to ANSI Z21.10.3. The water heater will
comply with paragraph 7.2.4.4, the thermal efficiency and the standby loss requirements of ASHRAE 90.1-1999.
Pressure Vessel and Heating Surfaces
The water heater will be a vertical fire tube design that is constructed and stamped in accordance with Section IV,
Part HLW of the ASME code. Both the storage and heating sections of the water heater will be National Board
Registered for a working pressure of 150 psi and will be pressure tested at 1-1/2 times working pressure. The fireside of
the heating surfaces will be of boiler-grade steel. The waterside of the heating tubes will be sealed in copper. The
heating tubes will be rolled, beaded, and seal welded into the tube sheets. The combustion side of the tube sheet will be
insulated by a layer of ceramic fiber that will protect the tube sheet from both thermal stresses and failure that can result
from the accumulation of scale and precipitants.
Lining
The lining will:
be applied only after the tank is completely fabricated and all welding is completed.
consist of multiple applications of a high-temperature fluoropolymer.
be continuous and nonporous with no interruptions or discontinuities.
require no sacrificial anode rods for protection.
Burner and Venting
Combustion will be provided by an induced-draft power burner that can operate with as little as 4-1/2 inches water
column of gas pressure. The water heater will be UL listed for use with plastic venting materials. The heater will be
capable of directly venting inlet air rated @ 120 equivalent feet and exhaust rated as follows: 4” vent - 50 equivalent feet
on 1 MBtu/h model, 100 equivalent feet for other inputs; 6” vent – 390 equivalent feet on 1Mbtu/h model, 500 equivalent
feet for other inputs.
The burner will be equipped with a gas train meeting the specifications of:
___ UL (standard equipment) ___ FM ___ IRI ___ Other ______________________
(continued)

PV 6150b 2/02 2
SPECIFICATION FOR DOMESTIC WATER HEATERS
Condensing, Gas-Fired Water Heaters with Polymer-Lined Storage Tanks
(continued)
Safety Controls
As a minimum, the heater will be equipped with the following:
•a solid-state flame safeguard with pre-purge, programmable post-purge, and flame status indicating lights
•two immersion operating thermostats
•an immersion temperature limiting device
•a stack temperature limiting device
•an ASME rated temperature and pressure relief valve
•and options as selected on form PV 6148
Warranty Summary
The burner and all heater parts will have a one-year warranty. Storage tank will have a five-year warranty covering
manufacturing or material defects, and/or the production of rusty water. Tank and heating surfaces will have a non-
prorated, three-year warranty against failure due to scale buildup with no provisions for periodic cleaning for warranty
coverage. If indicated here, the heater will also have a _____ first year or ____ long-life service policy, which will cover
replacement labor and freight costs under certain conditions. This summary is not a warranty. Consult warranty and
policies for full details. Complete copies of all warranties and service policies, including all exclusions and
conditions, will be presented to the owner as part of the submittal package.
Finishing
The storage and heating sections will be completely factory packaged and plumbed, requiring only job site hookup to
utilities, venting, and potable water inlet and outlet. The heater will be insulated to meet current ASHRAE standards,
jacketed with powder-coated steel panels, and mounted on heavy-duty channel skids. The heater will fit properly in the
space provided and installation will conform to all local, state, and national codes.
Start Up
Start up on the unit will be performed by factory trained and authorized personnel. A copy of the start up report will
be provided to the owner.
Quality Certification • Safety and Performance Standards
The heater will be UL listed. The water heaters will be manufactured by a company that has achieved certification to
the ISO 9001 International Quality Standard.