Pyle Pda69bu User manual

PDA69BU

Stereo Amplifier Audio Receiver Sound System

with Wireless BT Streaming, MP3/USB/SD/AUX/FM Radio

WARNING!

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

THE COVER OF THIS UNIT. THERE ARE NO USERSERVICEABLE PARTS

INSIDE. REFER ALL SERVICING TO A QUALIFIED TECHNICIAN.

1. Read these instructions thoroughly before using this item.

2. Keep these instructions for future reference.

3. Heed all warnings.

4. Follow all instructions.

5. WARNING: To prevent re or electric shock, do not expose this equipment to rain

or moisture. Do not store or operate this product near any liquids.

6. Clean only with a dry cloth.

7. Do not store or operate this product near any heat sources such as radiators, heat

registers, stoves, or other apparatuses (including ampliers) that produce heat.

8. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding plug

has two blades and a round grounding prong. The wide blade or third prong is

provided for your safety. If the provided plug does not t your outlet, consult an

electrician for the replacement of the obsolete outlet.

9. Protect the all wires connected to this unit from being walked on or pinched,

particularly plugs and the point where they exit from the unit. When removing the

cord from the power outlet, remove it by holding the plug not by pulling the cord.

10. Unplug the unit during lighting storms or when unused for long periods of time.

11. When wiring this unit and all other equipment used in connection to this unit

make sure that all of your equipment is turned OFF.

12. Once installation and wiring is complete power on all your equipment with the

volume and level controls turned DOWN. Once all the equipment is ON slowly

raise the volume or level controls to their proper positions.

13. When grounding this unit, be sure to do so correctly, so as not to defeat the

built-in grounding in this unit.

The lighting ash with arrow head symbol within an equilateral triangle is intended

to alert the user to the presence of “DANGEROUS”voltage within the product’s

enclosure that may be of sucient magnitude to constitute a risk of electric shock

to humans. Users should exhibit extra safety when this symbol appears in this

instruction manual and follow all precautions as they are stated.

The exclamation point within an equilateral triangle is intended to alert the user to

the presence of important operating and maintenance (servicing) instructions in

this manual.

www.PyleUSA.com

14. Before placing, installing, rigging, or suspending any product, inspect all

hardware, suspension, cabinets, transducers, brackets and associated equipment

for damage. Any missing, corroded, deformed, or non-load rated component

could signicantly reduce the strength of the installation, placement or array.

Any such condition severely reduces the safety of the installation and should be

immediately corrected. Use only hardware which is rated for the loading

conditions of the installation and any possible short-term, unexpected

overloading. Never exceed the rating of the hardware or equipment.

15. Consult a licensed, professional engineer regarding physical equipment

installation. Ensure that all local, state and national Regulations regarding the

safety and operation of equipment are understood and adhered to.

16. Refer all servicing to qualied service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or

has been dropped.

Introduction

To get the most from the Stereo Amplier Audio Receiver Sound System, it is

recommended that you review all of the information provided in the instruction

manual before operating the equipment.

ATTENTION

1. A: Connect the audio input with the CD/DVD/TV

audio output.

NOTES:

• PDA69BU does not support video signal, so make

sure that the CD/DVD/TV AUDIO OUTPUT terminal

are connected.

• Noise will be heard when you connect the unit with

CD/DVD/TV video output by mistake.

2. B: Signal output that can be connected with other

amplier or powered speakers

Input selector will not work if the

signal comes from the Line output.

3. STEPS FOR FM RADIO CONTROL

A. Connect the FM antenna before using the FM radio.

B. Press MODE button on the front panel or remote control to select FM mode.

C. Press PLAY/PAUSE button on the front panel or remote control, and will auto

scan and sore FM Radio station from 87.5Mhz to 108Mhz.

D. Press NEXT/PREV button to select the FM station.

4. REMOTE CONTROL

Remote control gives you commanding access only to USB/SD, Wireless BT and

FM functions and not the Master volume, microphone, bass, treble and other

functions.

A. Please take out the battery sheet before using the remote control, otherwise the

remote control will not work.

B. Press these two buttons to select the previous or next track in USB/SD or

Wireless BT mode, there is no response in the FM mode.

C. Press this two buttons to select previous or next channel in FM mode,

there is no response in the USB/SD and BT mode.

D. Press these two buttons to increase or decrease Wireless BT volume,

USB/SD and FM. This buttons doesn’t control the master volume.

E. Press this button to auto scan all frequencies from 87.5MHz to 108MHz, the

unit will auto store the channels in FM mode. Please see 4, C for other details.

F. Press this button to select one from play mode (USB/SD mode, FM mode and

Wireless BT mode). Turning ON the unit will set the USB/SD mode automatically.

MP3 les will be played automatically after inserting USB ash drive or SD card.

You cannot select the AUX, CD and DVD input with this button.

G. Press and hold this button for 5 seconds to turn ON or OFF the USB/SD,

Wireless BT and FM mode but not to power ON/OFF the unit. The unit will output

the signal in CD, DVD, AUX input mode if you turn OFF the USB/SD, Wireless BT

and FM.

H. Aim the remote controller at the receiver of the main unit.

5. FILE FORMAT

Only MP3 and WAV format are supported for USB/SD stored les.

The unit may skip the unsupported track les in USB or SD cards.

www.PyleUSA.com

6. USB PORT

The USB port is only used for playing audio les on your USB ash drive.

DO NOT use it for power supply as it may damage the unit.

7. CONTROL PANEL BUTTON

A. These buttons are only used to control the USB/SD, Wireless BT and FM functions

and doesn't control other functions.

B. MODE BUTTON: Press this button to select one from USB/SD mode, FM mode

or Wireless BT play mode. USB/SD mode will be set automatically after turning

ON the unit. Automatically plays mp3 les after inserting a USB ash drive or

SD card. You cannot select AUX, CD and DVD input on this button.

C. Each press of the PLAY/PAUSE BUTTON causes the operation to change from

play to pause or from pause to play in the USB/SD mode or Wireless BT mode.

Press the PLAY/PAUSE BUTTON one time to auto scan all frequencies from

87.5MHz to 108MHz in FM mode. Press the button to auto scan channels when

you use FM radio for the rst time. After stop searching, the unit will auto store

all the radio channels and play from the rst radio channel. You don't need to

rescan every FM radio start up.

D. PREV and NEXT BUTTON: Use these two buttons to select previous, next track

or folder, depending on these dierent modes as below.

• In USB/SD mode: Use to select previous or next track, or use to select previous

or next folder in FOLDER working mode.

• In Wireless BT mode: Use to select previous or next track.

• In FM mode: Use to select previous or next radio channel.

8. INPUT SELECTOR

Select MP3/BT input mode if you want to play USB/SD/Wireless BT/FM Radio.

Select CD input mode if you want to play CD jacks input signal. Select AUX input

mode if you want to play AUX jacks input signal. Select DVD input mode if you

want to play DVD jacks input signal, otherwise the unit output has no signal.

www.PyleUSA.com

FRONT & BACK PANEL

1. USB/SD Card/Wireless BT Control Console

After inserting a USB ash drive/SD Card into the input port, be sure to set the

input selector (14) to USB/SD, then press the mode button to choose between

audio from the USB port, SD Card input, Wireless BT or FM radio. If you want to

use the Wireless BT, check the below steps.

STEPS FOR CONNECTING WITH WIRELESS BT DEVICE

A. Press MODE button or Press BT button and enter into Wireless BT mode.

B. Search for the Wireless BT device and nd the BT name“PYLEUSA or BT”

C. Select the PYLEUSA or BT pairing name and wait for the device to pair.

D. The unit will make a sound conrming that the devices have successfully paired.

E. Once paired you can play music from your Wireless BT device. You can also use the

control buttons on the unit to select the tracks from your Wireless BT device.

F. Use the other controls, play/pause, previous track & next track to play audio from

Wireless BT.

www.PyleUSA.com

NOTE:

The USB input is ONLY meant to connect to a USB dash drive (thumb drive).

Connecting a MP3 player or computer directly to the USB ash drive input will result

the unit failing to play audio from those devices.

2. USB/SD Card Control Console Display Screen

1. MODE: The display will show "USB" when set to USB mode, "SD" when set to SD

card mode,"BLUE" when set to Wireless BT mode, "87.5 - 108" when set to FM mode.

2. BT: Wireless BT direct selection mode key.

3. : Previous track for USB/SD/BT model or Previous Station for FM model.

4. : This is Play and pause button; in FM mode, press and hold this button to

automatic search FM Station and automatic save Station.

5. : Next track for USB/SD/BT model or next radio Station for FM model.

6. Folder search mode: Press the folder/track knob, "F001" will show on LED display

screen, and rotate the folder/track knob to select a folder.

7. Track search mode: Rotate the folder/track knob or press the previous and next

buttons, the current track number will be showed here.

8. Elapsed time: The elapsed time of the current track will show here.

9. Shows FM frequency of the current station.

www.PyleUSA.com

3. Track/ Folder Searching Knob

• Turn this knob clockwise to search through all of the tracks inside the USB ash

drive/SD Card. Each track will appear by the number of the track. It will show the

tracks or folders chronologically (from when the les were loaded onto the USB

ash drive/SD Card. Press the knob to begin playing the desired track. First the

tracks on the root le will be displayed and then the tracks that are in folders.

• Press this knob to activate the folder searching function. Once pressed the word

“FOO1” wiII begin show on the display screen. Then, turn this knob clockwise to

search the folders inside the USB ash drive/SD Card. Press the knob to begin

playing the tracks from that folder.

1. SD Card Reader/USB Port: for using external media on this device, just plug your

SD/USB into these ports.

2. LED Screen: all information regarding external media or this device will be

displayed from this screen.

3. Folder and track selection

4. Master Volume Knob: adjust the master volume.

5. Power Switch: Press this Switch to turn the unit on and o.

6. MICROPHONE INPUTS: KARAOKE or EXTERNAL MIC connect to these.

7. Microphone Volume Control Knob: Turn this knob to adjust the microphone

volume level.

8. Microphone Delay time Control Knob: Turn this knob to adjust the microphone

delay time.

9. Microphone Reverb Depth Control Knob: Turn this knob to adjust the micro-

phone Reverb Depth.

10. Bass Control: Turn this knob to adjust the low frequencies of L CH and R CH.

11. Treble Control: Turn this knob to adjust the high frequencies of L CH and R CH.

12. Balance: Control the volume balance from left Chanel to right Chanel.

13. Headphone Output Jack: Connect the Headphone.

14. Input Selector: Turn this button to choose the favorable input.

15. IPOD/MP3 JACK-IPOD/MP3 connects to this jack.

16. AUDIO INPUT: Connect the audio output jacks of DVD/CD to these jacks.

17. LINE OUTPUT: Connect the RECORD input jacks to these jacks.

18. FM ANTENNA CONNECTOR: Connect for AM and FM antennas.

19. SPEAKER OUTPUT: Connect your speaker system to these terminals.

20. BT ANTENNA: Pease pull the antenna out when using Wireless BT input

21. POWER SUPPLY: Connect to AC 115V/60Hz and 230V/50Hz outlet.

22. POWER VOLTAGE SELECTOR: 115V/230V.