Pyle Pure Clean PSTMP90 User manual

USER MANUAL
PSTMP90
Table Top Steam Press

CONTENTS
Features of the Expresso..............................................1
Safety Reminders......................................................2
Part Identification...................................................3-4
Steam Press Operation
reparation for use......................................................5
Filling the water tank...................................................5
Turning on the power...................................................5
Selecting the temperature............................................6
Steam Control Notes....................................................7
Pressing....................................................................8
Finishing Pressing.......................................................9
Cleaning..................................................................10
Suggestion for Success.............................................11
Use of the Pressing Cushion......................................12
Techniques for Pressing.......................................13-14
Troubleshooting..................................................15-16
P

Table Top Stream Press
50% Faster Than Traditional Ironing
Safe for Nylon, Silk Rayon, Wool, Cotton, Linen, etc.
Non-Stick and Anti-Shine Ironing Surface Coating
Even Pressure Ensures Sharp, Long-Lasting Creases
Quickly Steam Press and Remove Wrinkles
Variable Temperature Selection
Multiple Dry-Heat & Steam Settings for Different Fabrics
Easy-to-Use and Safe One-Hand Operation
Extra Gentle Against Fabrics Like Silk
'Steam Burst' Function Blasts Away Wrinkles
(5) Times the Size of Regular Irons
Iron Surface Size: 22'' x 9''
Ready Indicator Lights
Auto Shut-Off Safety Feature
10 oz. Refillable Water Tank
1350 Watt Power
Accessory Kit Includes Spray Bottle, Pressing Cushion and Water Fill Cup
Dimensions: 24.0 x 10.2 x 22.0 Inches
Weight: 24.2 lbs.
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
1

ØTo protect against the risk of electric shock, do not immerse the
appliance in water.
ØDo not let the cord hang over the edge of counters.
ØDo not allow the cord to touch hot surfaces.
ØAlways allow the appliance to cool for at least thirty minutes before
storing.
ØAlways put the appliance in a secure place on a table or counter when
using.
ØDo not move the appliance without unplugging it first.
ØThe appliance has very hot surfaces - Do not allow unsupervised children
to use the appliance.
ØAlways disconnect the appliance from the outlet before filling with or
removing water. Be careful to avoid spilling water on the appliance when
filling.
ØUse distilled water in the appliance. Do not use perfumed or products
containing alcohol in the appliance.
ØAlways disconnect the appliance when not in use.
ØDo not use the appliance if the cord gets damaged. Return the appliance
or have the cord repaired by the manufacturer, his service agent or a
similarly qualified person.
ØDo not operate the appliance if it has been dropped or damaged. Do not
disassemble the appliance. Incorrect reassembly can cause a risk of
electric shock. Send it to an authorized service center for repair.
ØDo not operate another high wattage appliance on the same circuit.
ØThis appliance must be grounded. Do not alter the plug or attempt to
defeat this feature.
ØBe careful. Burns can occur from touching hot metal parts, hot water or
steam.
ØThis appliance is not intended for use by young children or infirm
persons unless they have been adequately supervised by a responsible
person to ensure that they can use the appliance safely.
ØYoung children should be supervised to ensure that they do not play with
the appliance.
THIS UNIT IS FOR HOUSEHOLD USE ONLY.
SAVE THESE INSTRUCTIONS
WARNING
Read all of the instructions and then save them for future reference.
SAFETY REMINDERS
2

3
10
3
1
4
5
11
2
6897
IDENTIFYING THE STEAM PRESS PARTS
1. The Pressing Handle raises and lowers the Pressing Plate. By lowering the
Pressing Handle until it reaches the lowest point possible you automatically
obtain maximum pressure.
2. The Locking Knob will lock together the Pressing Plate and Ironing Board. Use
the Locking Knob to carry or Store the Steam Press.
3. The Steam Burst Button on the end of the handle grip produces a burst of
steam when pressed.
4. The Pressing plate is the temperature controlled surface that heats and presses
the fabric.
5. The Ironing Board is the padded surface that holds the fabric during pressing.
6. The Power Indicator Light is illuminated when the unit is on.
7. The On/Off Switch can be pushed to turn the power on and off.
8. The Ready Light goes off when the Press has reached the selected temperature.
9. The Steam Ready Light goes on when unit is ready to produce bursts of
steam.
10. The Temperature Control dial is used to set the desired temperature for each
fabric.
11. The Water Tank slides forward and is filled through holes in the top. The
Water Level can be seen through the front of the tank. Slide the tank forward
for a better view.

12.The Ironing Board Cover is removable and washable for extended use.
13.The Pressing Cushion is a fabric covered pad used for pressing gathered or
contoured areas such as sleeves, darts, and yokes.
14. A plastic water Spray Bottle is used for dampening fabric before pressing.
15. A Water Container is used for filling the Water Tank.
16. Power light.
17. Temperature Ready Light.
18. Steam Ready Light.
Automatic features of the Steam Press include Auto Shut-Off and Auto Wake-up.
These multiple function safety features turn off electric power to the heater when
the Pressing plate has been left against the Ironing Board for more than 10
seconds OR if the Pressing plate is left in the open (up) position without use after
approximately 15 minutes. The heating ability of the unit is restored when the
Pressing plate is lowered or raised from its current position.
IMPORTANT NOTE: Auto Shut-Off does not mean power is totally cut off. Power
is always on, the Power Light remains on as well until the Power Switch is OFF. To
turn the power ON again, press the ON/OFF Switch to the OFF position, then back
to the ON position.
The following information is provided for service by a qualified electrician only:
Rated voltage: 120V, 60Hz, 1350W
WARNING:
This appliance must be grounded. Use only the proper type outlet when
plugging in the appliance. Do not attempt to override the ground wire feature.
4
13 14 15
16 17 18
12

STEAM PRESS OPERATION
STEP 1 - PREPARATION FOR USE
Set the appliance on a sturdy work surface. Unlock the Locking Knob.
STEP 2 - FILLING THE WATER TANK
BEFORE PLUGGING IN THE APPLIANCE, fill the water tank;
a. Always make sure the appliance is unplugged before filling the tank.
b. Fill the Water Tank with the Pressing Plate lifted to the raised (up) position.
Slide the Water Tank towards the front of the unit. It will not come
completely out so do not force it to do so. Using the Water Container,
slowly pour the distilled water into the Water Tank Fill Holes(C).
c. Be careful to avoid spilling water onto the Steam Press when filling.
d. Slide the Water Tank back into its recessed position.
STEP 3 - TURNING ON THE POWER
a. Always check to make sure the ON/OFF switch is OFF.
b. Make sure the Locking Knob is in the open position allowing free
movement of the Pressing Plate before plugging in the appliance.
c. Lift the Pressing plate to the fully raised (up) position.
d. Plug the appliance into an electric outlet.
e. Turn the ON/OFF switch to the ON position and the red Power Indicator
Light will shine. The Power Indicator light is the left most light on the
Indicator row.
5
C

6
STEP 4 - SELECTING THE TEMPERATURE
a. Turn the Temperature Control Dial (A) until it points to the kind of fabric you
wishtopress.
b. Examine the garment label if unsure and look up the type on the chart (B)
Below:
Nylon Silk Wool Cotton Linen
Acetate Polyester Triacetate
Rayon
IMPORTANT NOTE: If you can not determine the type of fabric, begin with the
lowest setting and increase the temperature as desired until you obtain the
properresults.
c. When the Ready Light (C) goes off, the Pressing Plate has reached the
temperatureforthedesiredsetting.
d. When changing the setting from a higher selection to a lower setting
allow several minutes for the Pressing Plate to cool sufficiently after
makingthechange.
IMPORTANT NOTE: You may find it more efficient to arrange your fabrics from
those requiring the lowest setting to those requiring the highest setting and
proceed accordingly. This will avoid any unnecessary delay or wait for the
PressingPlatetocool.

7
STEP 5 - STEAM CONTROL
IMPORTANT NOTE:
Steam is produced only when the Temperature Control Dial is set to the
higher temperatures.
The Temperature Control Dial must be set high enough to have sufficient heat
to produce steam. The center Temperature Ready Light goes off when the
unit has reached the desired temperature. The Steam Ready Indicator Light,
the right most light on the indicator row, will come on when the unit is ready
to produce steam.
IMPORTANT NOTE:
If this is the first time you are using the Steam Press or you have been
storing it for some time, lift the Pressing plate into the raised position and
press the Steam Burst Button several times until the steam begins to flow.
IMPORTANT NOTE:
The Steam Burst function can only be used when the Steam Ready Light is on
AND the steam press is in an opened position. Do not use the Steam Burst
function when the steam press is closed, or you may damage the unit.

8
TEP 6 - PRESSING
a. Lift the Pressing Handle (A). The Pressing Plate (B) moves to the up
position.
b. Carefully arrange the garment to be pressed onto the Ironing Board (C)
(the lower base of the Steam Press).
c. Grasp the handle of the Pressing Plate(A) and lower it onto the Ironing
Board (C),capturing the garment between the two halves of the Steam
Press. For light duty pressing, simply lowering the handle and allowing the
Pressing Plate to rest on the Ironing Board will be sufficient. Return to the
open position. For heavier duty pressing, continue to grasp the handle and
press downward until the Pressing Plate is pushed to its lowest position,
then open the press. If the Temperature Control is set high enough you
may give the fabric a burst of steam by pressing the Steam Burst Button
(D) to remove stubborn wrinkles. While the Pressing Plate is in the open or
up position, simply press down on the Steam Burst Button (D) and release
it. The fabric will be given a burst of steam.
d. After a few seconds, lift the handle and raise the Pressing Plate back to the
raised position.
IMPORTANT NOTE: If you forget to raise the Pressing Plate or become
distracted, the machine will give a warning beep and automatically shut-off
after approximately 10 seconds. The steam press will also shut-off after 15
minutes of no activity with the press in the open position. Auto Shut-Off does
NOT disconnect the power. Power is always on and the power light remains
on as well until the power switch is turned OFF. The shut-off feature is a
temporary aid until you can give full attention to the unit again.
DA
B
C