Wall bracket
1. Install the wall bracket on the strong wall.
2. Install the fan motor on the angle support bracket.
3. Assembling the back guard, blade, front guard to the motor.
IMPORTANT:
WARNING:
Surges in electrical power or excessive heat may cause the fan
to turn off. Wait approximately 15 minutes for the fan to resume operation.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY
TO PERSONS, OBSERVE THE FOLLOWING.
a) Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards, including fire-rated
construction.
b) Sufficient air is needed for proper combustion and exhausting of gases through
the flue(chimney) of fuel burning equipment to prevent back drafting. Follow the
heating equipment manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA), and the American
Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE),
and the local code authorities.
c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
The wall fan must be mounted by follow diagram way on 12 inch (300mm) thickdry
and cement - grouted firm wall or on 4 by 5 inch wood studs / joists.
INSTALLATION INSTRUCTIONS
Use wall bracket of wall mount assembly as a templet for locating the holes to be
drilled on mounting surface.
After determining the hole locations, use an appropriately sized drill bit and, drill
holes through mounting surface. Reference acceptable mounting surfaces and
appropriate drill bit sizes for application.
Attach wall mount assembly to mounting surface using hardware not provided. It is
recommended that a minimum of grade 5 fasteners be used. The following are
acceptable surfaces for mounting wall mount assembly.
STEEL SURFACE - When mounting to a steel surface of sufficient strength, such
as a vertical l-beam, drill through holes at pre-marked locations, using a 9/32" drill
bit. Attach wall mount assembly to mounting surface using 1/4"-20 hex screw of
appropriate length, in combination with 1/4" flat washers, 1/4" lock washers, and
1/4"-20 hex nuts.
MASONRY SURFACE - When mounting to a masonry surface use a 1/4" expansion
type bolt or 1/4" masonry lag with shield. Drill holes
at pre-marked locations using appropriate sized drill
bit as recommended for fastener.
NOTE:
HARDWARE NOT SUPPLIED
OPERATING INSTRUCTIONS
ING
TO ADJUST AIRFLOW UPWARD OR DOWNWARD:
SETTING OSCILLATING MODE:
SPEED CONTROL:
Loosen the position screw first and then loosen the pivot nut. Tilt motor to the
desired angle then firmly tighten the pivot nut
first and then tighten the position screw.
To oscillate the fan: Loosen the screw on the
oscillation rod and move to the end of the
oscillation cam. Tighten the screw to lock the
position.
To stop the oscillation: Loosen the screw on
the oscillation rod and move to the center of
the oscillation cam. Tighten the screw again
to lock the position.
Select air speed by setting switch to either high-low-off.
: Unplug from electrical supply source before cleaning.
1. Use soft damp cloth to clean, then wipe with dry cloth.
2. Do not use a cleaning solution that is harmful to paints or plastics.
3. Do not bend the blades.
¡ñ
¡ñ
CLEANING
WARNING
( )
( )
: Disconnect from mains before changing the setting.
See Figure 1
See Figure 2
CAUTION
RAT
FB2-50X # 120V~ 60Hz 185W 1.5A
FB2-75X # 120V~ 60Hz 220W 1.9A
10236
10306
ASSEMBLY INSTRUCTIONS
screw
fan motor
Figure 2
oscillation
cam
Angle support bracket
Pivot (Bolt,
Washer, Nut)
Set screw
Screw
Wall bracket
screw
fan motor
Figure 1
oscillation
cam
Position screw
For Questions and Assistance, please contact us at:
http://www.help2uonline.com
32
