Qdis W213-CT User manual

Installation Manual
Interface for Mercedes Benz
MBUX

Compatibility: Mercedes Benz MBUX
Components: Interface Main *1
Interface Input / Output specification:
Input:LVDS IN (Car System) *1
CVBS(Front Camera) *1
CVBS(Rear Camera) *1
Output:LVDS OUT (Car System) *1
Power Spec:
Input Power: 8VDC ~ 18VDC
Consumption: 5WATT
Switch input mode:
1. External video sources skip function: Able to control input videos on and off
via Dip switches
2. Able to switch videos via the remote control
3. Able to detect the rear view camera by CAN
2
1. Adjustable screen position of external device
2. Improved Screen Display(user-oriented interface)
3. Power output for rear camera
4. Dynamic PAS(parking assistance system)

3
Main Board
QCPASS
Power Cable IR Cable
HIRCAB0002
Remote Control
REMOTE0001
Dual Fakra Cable
HLCDCA0058
10Pin Wires
Power cable
(New)

PIN FUNCTION Dip S/W SELECT
1 Fcam
OFF : After Market Front Camera
ON : OEM Front Camera
2 R-CAM
OFF : OEM Rear Camera
ON : After Market Rear Camera
3 LCD Resolution
OFF : 1920 * 720
ON : 960 * 540
4 LCD TYPE(CAR MODEL)
OFF :
Without OEM T/S : C-CLASS(10”)
With OEM T/S : A-CLASS(10"), SPRINTER(7")
ON :
Without OEM T/S : E-CLASS(8.4”/12.3”), S-
CLASS(12.3”), C-CLASS(7”)
With OEM T/S : GLE(10"), A-CLASS(7")
4
* ON : DOWN / OFF : UP
Please make sure to disconnect the power cable
of the interface and reconnect the power cable
again to apply the dip switch changes.

5
Key FUNCTION
POWER & PIP N/C
MENU Activating OSD menu
OK Making a selection, changing image display
▲Moving upward
▼Moving downward
◀
Moving leftward
(If you press this button 2 seconds long, you can access the
factory mode)
▶
Moving rightward
(If you press this button 2 seconds long, you can reset all the
data about user environment)

PARK
PAS TYPE: Select parking line type.
- NOT USED: Do not use parking line
- PAS ON: Use Flexible Parking Lines
- PAS OFF: Use fixed parking line
PAS SETUP: You can move the position of parking line.
REAR TYPE : Choose rear camera recognition.
- CAN : By connecting to “CAN” cable of the car gear, changing to rear camera
mode when shifting into reverse. (Connect “CAN” cable of the power cable to the
“CAN” cable of the car gear)
- LAMP : By connecting to the rear lamp of the car, switch to rear camera mode
when shifting into rear. (Connect “Rear-C” cable of the power cable to the rear lamp
of the car)
AUTO FCAM: Time setting for the front camera display
(OFF, 3s, 5s, 10s, 15s)
RCAM TIME: After leaving R gear, Displaying Rear Camera screen as much as time set
RADAR ENABLE: OFF, TYPE 1, TYPE2
Type 1 : A class 10.1inch Split screen
Type 2: GLE 10.1inch Split screen
PARK
UTIL1
INFO
PAS TYPE
PAS SETUP
REAR TYPE
AUTO FCAM
RCAM TIME
RADAR ENABLE
Menu of FACTORY
MENU to Return SEL to Select/Save
6

UTIL1
FACTORY RESET: Factory mode reset
PARK
UTIL1
INFO
AVOUT SELECT
AUTO FCAM TIME
FCAM FUNC
NAVI MODEL
HDMI MODEL
FACTORY RESET
Menu of FACTORY
MENU to Return SEL to Select/Save
7
System version information
PARK
UTIL1
INFO
SYSTEM VERSION
(MAIN -210525)
Menu of FACTORY
MENU to Return SEL to Select/Save

8
* Press Return button on steering wheel to activate or deactivate PIP Function
7inch monitor
Small PIP screen
10.1inch monitor
Split screen to show OEM PDC
*Pressing PIP Button on Remote control has the same function.

9
Rear camera input *1
Front camera input *1
* Please refer next
page for LVDS in/out
connection
CAN-H
REAR DET.
CAN-L
12V SEL
FRONT DET.
REAR 12V
FRONT 12V
ACC (red) G ND(Black)

10
Find the red color double Fakra
connector behind the command
MBUX HU
OEM Cable
OEM Angle
type double
Fakra
connector
OEM HU
LVDS IN LVDS OUT

11

Q. I cannot change mode
A. Check connection of Ground cable and IR Cable. Check LED lamp is on, if not
check connection of POWER cable.
Q. All I got on the screen is black.
A. Check second LED lamp of the interface is on, if not, check Video sources
connected are working well. (Second lamp indicates Video sources connected
works well) Check interface connection has been done well.
Q. Displayed image color is not proper (too dark or unsuitable color)
A. Press ▶ button on the remote control for 2 seconds and check how it goes, if it
does not work, inform to manufacturer.
Q. I cannot watch the rear camera on the screen
A. Set the DIP switch #7 as state “ON”.
Q. Set mode not appear
A. Check DIP Switch.
Q. OEM image is not displayed.
A. Check interface’s LCD In/Out cable connection. If the status keeps on, inform to
manufacturer.
Q. Screen only displays white color.
A. Check LCD out cable is connected well, if this status keeps, inform to
manufacturer.
Q. If no image is shown on screen after connecting CAN wire with Park gear.
A. Go on the “FACTORY MODE”, check “UTIL-Rear Select”. If “LAMP”, change the
setting as “CAN” with the remote control. ( ※ when connecting Rear-C wire of LAMP
power cable to Backup lights, Setting should be like this / CAN : if controlling rear
camera with CAN wire)
12

RM #404 4TH FLOOR, B-DONG,
WOORIMLIONSVALLY, 371-28, GASAN-DONG,
GEUMCHEON-GU, SEOUL, KOREA.
TEL : [phone]~9 | FAX : 82-2-2026-5987
13