QERIDOO Kidgoo1 Sport User manual

EN
Disc brake addon 2018

V
I
D
E
O
T
U
T
O
R
I
A
L

Documentation
The statements in this documentation are not to be interpreted as an assurance of
particular product properties. Despite the greatest care being taken to avoid technical
inaccuracies or omissions, the possibility of these arising cannot be entirely excluded.
When necessary, individual items of information can be changed quickly and without
special notification.
This documentation can be ordered from Qeridoo GmbH in other languages, or is available for
download on our website if already available.
Visit us at: www.qeridoo.de
Danger!
This manual is only valid in conjunction with the Qeridoo user manual.
Copyright
All rights to the documentation remain with Qeridoo GmbH.
Texts, values and illustrations may not be reproduced, distributed, used for competitive purposes or
passed on to others. If other product names are used in this documentation, these must normally
be regarded as registered trademarks of the respective manufacturer.
Scope of delivery
1Jogger strap
2Set of screws; Ferrule
3Brake lever
4Brake cable with branch point
5Supporting feet
6160 mm rotors
7Velcro fasteners
8Brake calipers with bracket
The disc brake can be retrofitted to the following models:
Speedkid 2018 (Q2-18)
Sportrex 2018 (Q3-18, Q6-18)
Kidgoo 2018 (Q8-18, Q9-18)
If necessary, follow the QR code to view a video on the Internet for
installation and operation:
2– 05|2018 – Subject to change. Disc brake addon 2018

V
I
D
E
O
T
U
T
O
R
I
A
L

For assembly and adjustment Allen key size 3, 4 and 5,
as well as a pair of pliers are needed. Depending on the
model used, an additional size 7 spanner is required.

fTurn the railer onto the roof to better reach the axle.
fTake off the wheels.
fActivate the parking brake function.
fLoosen the 3 wheel pins on both wheel receivers.
Depending on the model, use either a size 7 spanner
or a size 4 Allen key.
fReplace the black spacer plates with the rotors,
observing the direction of rotation shown on the
rotors.
fTurn the rotor around if the direction is wrong.
fScrew the wheel pins back in place.

fSlide the feet onto the slide mount on the axle.

The calipers are attached to the axle with the metal bracket. Pay attention to the correct alignment
of the calipers. The brake cable retainer must point to the bottom of the trailer and the brake cable
clamp away from it. The metal bracket points to the rear of the trailer.

The holders for the metal brackets on the axle are cast from aluminum and can the-
refore have production-related burrs or residues. We therefore recommend piercing
them with an Allen key prior to installation so that the screws can be inserted without
hindrance.
Disc brake addon 2018 Subject to change. – 05|2018 – 3


fHold the caliper with the metal bracket to the mount.
Make sure the two holes in the bracket are aligned
with the holes in the mount.
fUse a size 4 Allen key to screw the supplied screws
into the bracket and tighten them securely.
The calipers have a 2-piston brake technology, which allows both brake pads to be set individually.
For the adjustment you need a size 3 and 5 Allen key. The smaller key is used on the black inside of
the caliper and the larger key on the bronze outside.

To adjust the inner brake piston, insert the Allen key into the caliper as far as it will go.
fMove the inner brake piston slightly closer to the rotor
of the disc brake by turning the size 3 Allen key 1/4
turn.
fLoosen the two blue highlighted screws on the caliper
with the aid of a size 5 Allen key. The caliper can now
be moved laterally.
fPush the brake caliper sideways against the rotor of the disc brake so that the inner brake pad
of the brake caliper rests flat.
fTighten the two caliper screws again.
fScrew back the inner brake piston slightly so that there is a small distance to the rotor.
fUse the size 5 Allen key to bring the outer brake pad closer to the rotor. The distance should be
less than one millimeter.
fCheck if the rotor can rotate freely without blocking. If necessary, adjust the two brake pistons
to allow the rotor to rotate freely. The distance to the brake pads should be kept as low as
possible.
fRepeat the process with the second caliper.

New brake pads must first be braked in. You should allow the brake to be easily grinded
up to 30 times, each over a distance of several meters. Disc brakes achieve the full
braking effect only after braking in.

The brake lever can be mounted in two positions, either for right or left-handers.
fPush the padding of the push handle apart by about 4
cm on the desired position.
fLoosen the two screws on the brake lever clamp by
using a size 4 Allen key.
fPosition the brake lever onto the tube of the push
handle and fix it by retightening the screws on the
clamp.

4– 05|2018 – Subject to change. Disc brake addon 2018


Brake lever
The brake cable is similar to an inverted Y and has two legs of different length. Depending on the
selected position on the push handle, the brake cable is guided into the cabin on the opposite side
of the lever (Sportrex & Kidgoo) or guided along the side of the trailer (Speedkid).
fAlign the silver adjustment screws so that the side
notches form a straight line.
fInsert the barrel-shaped end of the brake cable into the
socket on the brake lever and insert the brake cable
sleeve into the socket of the adjusting screw.
fTurn the adjusting screw half a turn to prevent the
brake cable from falling out.
fUse the Velcro straps to fix the brake cable along the push handle.
Brake cable branch point
fSlide the two brake sleeves over the brake cables.
Make sure that the shorter sleeve caps are facing
upwards.
fInsert the end caps of the brake cables into the socket
on the underside of the brake cable branch point.
fFeed the brake cable ends through the openings in the
cabin floor (Sportrex and Kidgoo) or guide them to the
side of the brake calipers (Speedkid).
Brake caliper
fUse a size 5 Allen key to slightly loosen the screw on
the brake cable clamp.
fPass the end of the brake cable through the brake
cable retainer so that the end cap of the sleeve is
firmly seated in the socket. Make sure that the entire
brake cable is firmly seated in the respective sockets
and that it is sufficiently tensioned.
fPass the exposed brake cable end through the brake cable clamp and pull on the brake cable
to build up some tension.
fPull the arm of the brake cable clamp about one cm
towards the brake cable retainer and retighten the
screw at the end of the clamp.
Disc brake addon 2018 Subject to change. – 05|2018 – 5
