QISTA BAM User manual

Mosquito trap
installation
guide
(BAM)
Technopole de l’Arbois
Avenue Louis Philibert
Bâtiment MEGIE
13100 Aix en Provence
0 806 110 640
[email protected]
www.qista.com

Your mosquito trap components
Suction fan
Filter
Collecting
net
Pressure
gauge
CO2
connection
bend
CO2 ow
ajustement
knob
CO2REGULATOR
Recommendations for use Application Qista
Caution, the bottle
must be returned after
a maximum of 60 days
after collecting from the
supplier.
60
JOURS
The mosquito trap is
designed for exclusively
outdoor use. If you store
the BAM inside your
house, make sure you
have correctly closed the
CO2bottle.
Make sure to close the CO2
bottle correctly before
disconnecting the CO2
regulateur. The bottle must be
closed even when empty.
Do not store the CO2bottle in an
enclosed area
With the Qista application you can:
Do an implementation study to know
the best location for your traps.
Control your traps individually or in a group
Choose the operating program that best suits your exterior
Check the status of your consumables
Check the capture statistics of each trap
Consult the meteorological data
Access the application download link on:
https://qista.com/application-qista
Meteorological
captor
Cover
If you do not have a
Smartphone to control
your BAM, contact
Qista to perform the
programming
Do not disconnect the
power cord without rst
switching o via the
application, this leads
to malfunctions of the
solenoid valve and leads
to an overconsumption
of CO2.
The mosquito lure is
a volatile compound
impregnated on
small plastic beads.
The olfactive lure
evaporated gradually
but the plastic beads
keep their solid state,
they do not melt.
Do not obstruct
the weather sensor
this could disrupt
the programs of your
machine.
STEP 2: INSTALL THE NEW FILTER
3Clip the new lter onto the cartridge.
4Screw the cartridge back on (counterclockwise).
5
Check that the lower valve is closed to avoid
abnormal CO2 consumption by turning it a quarter
turn counterclockwise.
1
2
3
Replacing the lter
For optimal maintenance of the BAM, it is recommended to replace the lter every year,
at the beginning of the season.
STEP 1: REMOVE THE USED FILTER
1Unscrew the cartridge clockwise.
2Unclip the used lter from the cartridge
by unscrewing it counterclockwise.

1Use the key to open the rear door of the machine
and connect the machine to an electrical socket.
2
Connect the regulator to the CO2 diusion
system: take the black tube from inside the
terminal and connect it to the CO2connecting
bend.
3
Screw the expansion valve onto the CO2
regulator. Screw it fully and then tighten gently
using an adjustable spanner.
4
Open the CO2bottle by turning the valve
counterclockwise. Warning, this may be dicult.
5
Adjust the CO2 ow rate: turn the black knob on
the regulator until the needle is set to the value
indicated on the label attached to the pressure
gauge. After 24 hours, check that the hand still
indicates the same value.
6
Test the CO2 ow: block the end of the CO2tube
with your thumb and wait 10 seconds.
Remove your thumb, you should hear the gas
escaping.
Connecting
the CO2
1Place the cover on the trap starting with the
right-angle A, without closing it.
2Insert the secondary fan Bconnector and the
CO2Csupply pipe into the correct slot.
3Fit the cover back on.
4Insert the lure after having removed the lid.
Close the cover.
Installation
of the cover
13
2
3
5
4
0,6
0,8
A
C
B
To recover the
key from your
terminal, unscrew
the cap from the
chimney.
Time programming
4
Before inserting the CO2bottle
into the terminal:
GClip the black electrical box to the bottom
of the BAM in the intended location
HPass the power supply cable through the
cable guide chanel on the oor of the
terminal
The CO2bottle must be well positioned
correctly so as not to interfere with the
closing of the gate.
To close the lock, hold the 2
parts of the gate with one hand
and close the lock with the
other.
Then lock with a key
to secure the lock.
G
H
1Contact Qista to get
your username
2
Install the Smartphone application
3
Set the machine according to the type
of mosquito present (the default mode is
tiger mosquito)
Starting up
5
1Use the key to open the front cover of the BAM.
2The cover can be screwed to the BAM from
below to reinforce its support .
3Connect the various elements to the plugs
provided at the top of the machine:
DElectronic board / ESecondary fan
FMain fan
4Lock the cover with the key.
Electrical
connection
2
F
E
D