Qlogic BR-1020 User manual

BR0054506-00 C
Quick Start Guide
FCoE Converged Network Adapter
BR-1020

ii BR0054506-00 C
Quick Start Guide FCoE Converged Network Adapter
BR-1020
Information furnished in this manual is believed to be accurate and reliable. However, QLogic Corporation assumes no
responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its
use. QLogic Corporation reserves the right to change product specifications at any time without notice. Applications
described in this document for any of these products are for illustrative purposes only. QLogic Corporation makes no
representation nor warranty that such applications are suitable for the specified use without further testing or
modification. QLogic Corporation assumes no responsibility for any errors that may appear in this document.
Document Revision History
Revision A, April 30, 2014
Revision B, October 6, 2014
Revision C, March 31, 2015
Changes Sections Affected
Updated the support headquarters address “Contact Information” on page vi
Corrected the note in Step 6 to reference the Con-
verged Network Adapters cabling section. “Installing Hardware” on page 2

iii BR0054506-00 C
Welcome
Thank you for purchasing a QLogic BR-1020 FCoE Converged Network Adapter.
This adapter provides reliable, high-performance connectivity to Ethernet-based
hosts for mission-critical Storage Area Network (SAN) environments.
The QLogic BR-1020 FCoE Converged Network Adapter is a dual-port, 10Gbps
adapter that combines the functions of a host bus adapter and a NIC on one PCIe
x8 card. This converged network adapter fully supports FCoE protocols and
allows Fibre Channel traffic to converge onto 10Gbps Converged Enhanced
Ethernet (CEE) networks. The combined high performance and proven reliability
of a single-ASIC design makes this converged network adapter ideal for
connecting hosts to SAN fabrics based on Brocade Fabric OS®(FOS) or Brocade
M-Enterprise OS (M-EOS).
Related Materials
The following documents are available on the QLogic Web Site:
BR-Series Adapters Installation Guide
BR-Series Adapters Troubleshooting Guide
BR-Series Adapters Administrator’s Guide
For information about downloading documentation from the QLogic Web Site, see
“Downloading Updates” on page v.
NOTE
Install only QLogic-supported SFPs in these adapters.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Welcome
iv BR0054506-00 C
Documentation Conventions
This guide uses the following documentation conventions:
provides additional information.
Text in blue font indicates a hyperlink (jump) to a figure, table, or section in
this guide, and links to Web sites are shown in underlined blue. For
example:
Table 9-2 lists problems related to the user interface and remote agent.
See “Installation Checklist” on page 3-6.
For more information, visit www.qlogic.com.
Text in bold font indicates user interface elements such as a menu items,
buttons, check boxes, or column headings. For example:
Click the Start button, point to Programs, point to Accessories, and
then click Command Prompt.
Under Notification Options, select the Warning Alarms check box.
Text in Courier font indicates a file name, directory path, or command line
text. For example:
To return to the root directory from anywhere in the file structure:
Type cd /root and press ENTER.
Enter the following command: sh ./install.bin
Key names and key strokes are indicated with UPPERCASE:
Press CTRL+P.
Press the UP ARROW key.
Text in italics indicates terms, emphasis, variables, or document titles. For
example:
For a complete listing of license agreements, refer to the QLogic
Software End User License Agreement.
What are shortcut keys?
To enter the date type mm/dd/yyyy (where mm is the month, dd is the
day, and yyyy is the year).
Topic titles between quotation marks identify related topics either within this
manual or in the online help, which is also referred to as the help system
throughout this document.
NOTE

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Welcome
v BR0054506-00 C
Technical Support
Customers should contact their authorized maintenance provider for technical
support of their QLogic products. QLogic-direct customers may contact QLogic
Technical Support; others will be redirected to their authorized maintenance
provider. Visit the QLogic support Web site listed in Contact Information for the
latest firmware and software updates.
For details about available service plans, or for information about renewing and
extending your service, visit the Service Program Web page at
http://www.qlogic.com/Support/Pages/ServicePrograms.aspx.
Downloading Updates
The QLogic Web site provides periodic updates to product firmware, software,
and documentation.
To download firmware, software, and documentation:
1. Go to the QLogic Downloads and Documentation page:
driverdownloads.qlogic.com.
2. In the search box, type the QLogic model name.
3. In the search results list, locate and select the firmware, software, or
documentation for your product.
4. View the product details Web page to ensure that you have the correct
firmware, software, or documentation. For additional information, click
Read Me and Release Notes under Support Files.
5. Click Download Now.
6. Save the file to your computer.
7. If you have downloaded firmware, software, drivers, or boot code, follow the
installation instructions in the Readme file.
Instead of typing a model name in the search box, you can perform a guided
search as follows:
1. Click the product type tab: Adapters, Switches, Routers, or ASICs.
2. Click the corresponding button to search by model or operating system.
3. Click an item in each selection column to define the search, and then click
Go.
4. Locate the firmware, software, or document you need, and then click the
item’s name to download or open the item.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Welcome
vi BR0054506-00 C
Training QLogic Global Training maintains a Web site at www.qlogictraining.com offering
online and instructor-led training for all QLogic products. In addition, sales and
technical professionals may obtain Associate and Specialist-level certifications to
qualify for additional benefits from QLogic.
Contact Information
QLogic Technical Support for products under warranty is available during local
standard working hours, excluding QLogic Observed Holidays. For customers
with extended service, consult your plan for available hours. For Support phone
numbers, see the Contact Support link at support.qlogic.com.
Knowledge Database
The QLogic knowledge database is an extensive collection of QLogic product
information that you can search for specific solutions. QLogic is constantly adding
to the collection of information in the database to provide answers to your most
urgent questions. Access the database from the QLogic Support Center:
support.qlogic.com.
Support Headquarters QLogic Corporation
12701 Whitewater Drive
Minnetonka, MN 55343 USA
QLogic Web Site www.qlogic.com
Technical Support Web Site support.qlogic.com
Technical Support E-mail [email protected]
Technical Training E-mail [email protected]

1 BR0054506-00 C
Installation Instructions
Installing a QLogic BR-1020 FCoE Converged Network Adapter consists of the
following tasks:
“Verifying Installation Requirements” on page 1
“Verifying Items for Installation” on page 1
“Preparing the Host System” on page 2
“ESD Precautions” on page 2
“Installing Hardware” on page 2
“Installing Software” on page 5
Verifying Installation Requirements
Before you begin, make sure that your server (host) system meets hardware and
software compatibility requirements outlined in the BR-Series Adapters
Installation Guide and the system is fully operational.
Verifying Items for Installation
Have the following items on hand for installation:
Fully functional host
Phillips #1 screwdriver
Adapter with appropriate mounting bracket attached
Appropriate cable with LC duplex connectors to connect the adapter to the
FCoE switch.
NOTE
The adapter ships with two different bracket sizes. If the bracket that
you require is not already attached to the adapter, instructions are
included in this guide to attach it.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Preparing the Host System
2 BR0054506-00 C
Preparing the Host System
1. Make a backup of the system data.
2. Power down the host system. Unplug all power cords and network cables.
3. Remove all covers necessary to access the PCIe®slot in which you want to
install the adapter. Refer to your system documentation to locate PCIe slots
and cover removal procedures.
4. Remove the blank bracket panel that covers the PCIe slot in which you want
to install the adapter. If the panel is secured with a screw, remove the screw
and save it for securing the adapter bracket panel into the slot.
ESD Precautions
When handling the adapter, use correct electrostatic discharge (ESD) procedures:
Wear a wrist grounding strap connected to chassis ground (if host is plugged
in) or a bench ground.
Store the adapter in anti-static packaging.
Installing Hardware
NOTE
Install adapters in PCI-Express slots that use an x8 lane transfer
interface or greater for best performance. You cannot install adapters
into PCI™ or PCI-X™ slots.
NOTE
When installing a BR-1020 Converged Network Adapter on VMware®
systems,itisadvisableto installthedriverpackagebeforetheadaptersothat
thenetworkinterfacecontrollers(NICs)areproperlynumberedinthesystem.
Perform all steps under “Software Installation on VMware Systems” on
page 10, and then return to this section.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Hardware
3 BR0054506-00 C
To Install the adapter hardware into your host system:
1. If fiber optic SFP transceivers are installed in
the adapter, remove them if clearances
inside your system case prohibit installation
with them installed.
a. Pull out the protective rubber plug from
the SFP connector.
b. Using your thumb and forefinger,
unlatch the bail from the side of the
fiber optic cable connector and pull the
SFP straight out of the receiver. Arrows
stamped on the bail mark the location
where you unlatch it.
2. The adapter ships with one bracket installed
and another size bracket in the shipping container. If the installed bracket
works as is, go on to Step 3.
If your system chassis requires a different bracket (low-profile or standard)
to secure the adapter in the slot, perform the following steps to replace the
bracket. Note that you must remove SFPs first to remove this bracket (refer
to Step 1).
a. Remove the two screws attaching the
bracket to the adapter, and pull off the
bracket.
b. Carefully guide the new mounting
bracket onto the adapter, making sure
the bracket mounting tabs align with the
holes in the adapter.
c. Replace and tighten the two screws.
d. Store the mounting bracket that you
removed for future use.
The illustration shows the standard bracket.
PORT
01

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Hardware
4 BR0054506-00 C
3. Insert the adapter into the desired empty PCIe bus slot. Press firmly until the
adapter is seated.
4. Secure the adapter’s mounting bracket to the case using the method
required for your case. In some systems, the bracket may be secured to the
case with a screw.
5. Replace the system’s case or covers and tighten all screws.
Edge of
Host Board
Press Here
Screw
Press Here
PCI Express
X8 Slot
SFP Receivers

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Software
5 BR0054506-00 C
6. Install all SFPs if not already installed.
a. Orient the SFP in front of its slot on the adapter so that it can slide into
the adapter’s receiver slot. The SFP can be oriented only one way into
the slot.
b. For fiber optic SFPs, use the bail or pull tab as a handle, and then slide
the SFP into the receiver until seated. Latch the bail.
c. For copper cable SFPs, grasp the SFP with your thumb and forefinger
and slide it into the receiver until it latches.
7. Replace the system’s case or covers and tighten all screws.
8. Connect the adapter to the FCoE switch.
For fiber optic SFPs:
a. Pull out the protective rubber inserts from the fiber optic SFP
connectors, if installed in the switch or adapter.
b. Connect the cable to the adapter and the appropriate LC connector on
the FCoE switch.
For copper cable SFPs, connect the cable to the adapter and to the
appropriate LC connector on the switch.
9. Turn on host power and observe LED operation. Refer to the “LED
operation” section for your adapter in the “Specifications” chapter of the
BR-Series Adapters Installation Guide for details on LED operation.
Installing Software
Use the Adapter Software Installer (ASI) to install the Host Connectivity Manager
(HCM), all driver packages, and utilities based on your host operating system. The
following procedures assume that the host’s operating system has been installed
and is functioning normally.
“Software Installation on Windows, Linux, and Solaris Systems” on page 6
“Software Installation on VMware Systems” on page 10
NOTE
Use the correct cable with LC connectors to connect the adapter to the
FCoE switch. For information on compatible cables and maximum
distances supported by cable types, refer to the Converged Network
Adapters cabling section in the “Specifications” chapter of the
BR-Series Adapters Installation Guide.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Software
6 BR0054506-00 C
ASI can install HCM either on the local host or any remote system. An HCM
desktop shortcut is available after installing HCM on Windows®, Linux®, and
Solaris®systems. Only one driver installation is required for all adapters installed
in a host system.
Software installation could take much longer than normal with a large number of
adapters installed or where a large number of LUNs are exposed through different
paths to the multipath software. For more details and options on installing adapter
software, such as using ASI or native installation system commands, refer to the
“Software Installation” chapter in the BR-Series Adapters Installation Guide.
Software Installation on Windows, Linux, and Solaris Systems
Before installing software on a Windows, Linux, or Solaris system, consider the
exceptions in the following table:
OS Exception
Windows When installing driver packages on Windows 2008 and later systems,
open TCP/IP port 34568 to allow HCM Agent communication with the
HCM. (Necessary because of firewall issues.) Following is an example
for opening port 34568:
/usr/sbin/esxcfg-firewall -o 34568,tcp,in,https
/usr/sbin/esxcfg-firewall -o 34568,udp,in,https
Use Windows Firewall and Advanced Service (WFAS) to open port
34568.
Before installing drivers on Windows systems, install the following hot
fixes from the Microsoft®“Help and Support” Web Site, and then reboot
the system. For more information on these hot fixes, refer to “Installation
Notes” in the BR-Series Adapters Installation Guide.
Windows 2008: KB968675 and KB2490742 are recommended.
KB958015 is recommended for ports configured in CNA mode
Windows 2008 R2: KB977977 is recommended for ports configured
in CNA mode. KB2490742 is recommended when installing storage
drivers.
For Windows systems only, installing management utilities creates a
BCU shortcut on your system desktop. Use this shortcut to launch the
BCU> command prompt and enter BCU commands.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Software
7 BR0054506-00 C
To install adapter software on Windows, Linux, and Solaris systems:
1. Download the Adapter Installer Software for your adapter:
a. Go to the QLogic Web Site at driverdownloads.qlogic.com and select
the Adapters tab and the by Model radio button.
b. In the table, select Fibre Channel Adapters in the first column,
BR-1020 or BR-1010 in the second column, the operating system in
the third column, and then click Go.
c. In the Software Installers table, locate the installer package, click on it,
and then follow the directions.
2. Execute the appropriate Adapter Software Installer (refer to Step 1). When
all files are extracted, an Adapter Software title window appears.
3. When the Adapter Software Installer Introduction window appears, read the
recommendations and instructions, and then click Next.
4. When the License Agreement appears, select I accept the terms of the
License Agreement, and then click Next to continue.
Linux SLES When installing the source-based (noarch) driver packages
(brocade_driver_linux_<version>.tar.gz) or when using the ASI and the
kernel has been upgraded to a version without pre-compiled binaries,
perform the following tasks to make sure the drivers load. Afterwards, be
sure to reboot the system.
For Linux SLES®10 systems, make sure the load_
unsupported_modules_automatically variable is set to yes in
/etc/sysconfig/hardware/config.
For Linux SLES 11 systems, make sure the
allow_unsupported_modules variable is set to 1in
/etc/modprobe.d/unsupported-modules.
Run the mkinitrd command to load automatically during system boot.
By default, the initrd file will be backed up automatically during Linux
installations. During installation, a dialog box shows the location of the
file. If a file exists, a dialog box allows you to overwrite the file, not
overwrite the file, or quit.
Solaris After installing drivers on Solaris system, you must reboot the system to
enable the drivers.
OS Exception

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Software
8 BR0054506-00 C
5. If a backup directory exists for previously installed software, a Found
Backed up data message prompts you to restore old configurations.
Select either to restore or not to restore and continue installation. If this
message does not appear, go on to Step 6.
6. If a message window lists existing software components already installed on
your system, select one of the following options, and then click Continue,
and then skip to Step 10. If this message does not appear, go on to Step 7.
Install with existing configuration. The installer compares each
configured property and keeps the original value if different from the
default value.
Install with default configuration. The installer upgrades the
software and loads with default configurations.
7. If a message prompts you to close HCM, close the application if it is running,
and then click OK on the message box.
8. When the Choose Install Set window appears, select the software you want
to install, and then select Next.
If you are installing the management utilities and messages warn that HCM
agent requires storage and network driver installation or does not match
current driver installation, and then click OK, and then select the
Management Utilities and Storage and Network Drivers options to install.
If a message warns that the installed boot image is not compatible with the
driver installation, perform one of the following steps:
Select Yes to update the image and continue installation.
Select No to not update the image and continue installation.
9. If the Choose Install Folder window prompts you to choose a destination
folder for the software, select one of the following options. If this window
does not appear, go on to Step 10.
Enter a location for installing the software.
Select Choose to browse to a location on your file system.
Select Restore Default Folder to enter the default installation folder.
10. When the Package Location Information window lists the installed software
components and their location on your system, select Next to continue.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Software
9 BR0054506-00 C
11. Review information on the Pre-Installation Summary window and select
Install to begin installation.
A progress bar shows the installation progress.
12. When the Install Complete window lists installed components, confirm that
all components are installed and select Done. If a message instructs you to
restart or reboot the system, select any options that apply.
13. Verify driver installation through tools available on your host system. Refer to
the “Confirming Driver Package Installation” section in the “Software
Installation” chapter of the BR-Series Adapters Installation Guide for details.
14. To make sure that the drivers and adapter boot code are synchronized, be
sure to update your adapter using the latest boot image:
a. Go to the QLogic Web Site at driverdownloads.qlogic.com and select
Adapters, by Model.
b. In the table, select Fibre Channel Adapters in first column, BR-1020
in the second column, the operating system in the third column, and
then click Go.
c. Click the Boot Code link at the top of the page to direct you to the boot
code packages.
d. Locate the boot code package for your adapter in the table, click on it,
and then follow the directions.
For instructions on installing the boot image, refer to the “Boot Code”
chapter in the BR-Series Adapters Installation Guide.
15. When the driver is installed and the host system is connected to the FCoE
switch (refer to step 8 on page 5) observe adapter LED operation. Verify
proper LED operation by referring to “LED operation” in the “Specifications”
chapter of the BR-Series Adapters Installation Guide.
NOTE
For Windows systems, a Force Driver Installation message
box appears if a better driver is already installed for the adapter. If the
message appears, select OK to overwrite the existing driver or Cancel
to quit installation.

BR-1020 FCoE Converged Network Adapter Quick Start Guide
Installing Software
10 BR0054506-00 C
Software Installation on VMware Systems
The ASI is not supported on the VMware “console” operating system for installing
drivers, HCM, and utilities. However, you can use an applicable software installer
from the list under “Software Installation on Windows, Linux, and Solaris Systems”
on page 6 to install HCM on a “guest” system.
To install VMware drivers and utilities:
1. Download the appropriate package using the following steps:
a. Go to the QLogic Web Site at driverdownloads.qlogic.com and select
the Adapters tab, the by Model radio button, and then click Go.
b. In the table, select Fibre Channel Adapters in the first column,
BR-1020 in the second column, VMware ESX/ESXi in the third
column, and then click Go.
c. Locate the driver package in the table of drivers for your version of
VMware ESX®/ESXi, click on it, and then follow the directions.
2. Copy the file to your system’s /tmp directory.
3. Follow instructions for ESX or ESXi installation under “Driver installation and
removal on VMware systems” in the Software Installation chapter of the
BR-Series Adapters Installation Guide.
Because some versions of ESX and ESXi do not enforce maintenance mode
during driver installation, it is recommended to put the host in maintenance mode,
as a reboot is required after installation.
NOTE
When installing driver packages on VMware systems, open TCP/IP port
34568 to allow HCM Agent communication with the HCM. (Necessary
because of firewall issues.) On VMware systems open port 5989 to allow
communication for CIM Provider.
Following is an example for opening port 34568:
/usr/sbin/esxcfg-firewall -o 34568,tcp,in,https
/usr/sbin/esxcfg-firewall -o 34568,udp,in,https

Corporate Headquarters QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com
International Offices UK | Ireland | Germany | France | India | Japan | China | Hong Kong | Singapore | Taiwan
©2014,2015QLogicCorporation. Specificationsaresubjectto changewithoutnotice.Allrightsreservedworldwide.QLogic,the QLogiclogo, and AnyIO aretrademarks or registered trademarks
of QLogic Corporation. Brocade is a trademark of Brocade Communications Systems, Inc., in the United States and/or in other countries. PCIe, PCI, and PCI-X are trademarks or registered
trademarksofPCI-SIGCorporation.MicrosoftandWindowsareregisteredtrademarksofMicrosoftCorporation.Linuxisaregisteredtrademarkof Linus Torvalds.Solaris isa registeredtrademark
of Oracle Corporation. VMware and ESX are registered trademarks of VMware, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.
Information supplied by QLogic Corporation is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves
the right, without notice, to make changes in product design or specifications.