Qlogic SANbox 3050 User manual

Quick Start Guide
[]
FIBRE CHANNEL SWITCH INSTALLATION P
QUICK START GUIDE
SANbox®3050
for Windows®Operating Systems

1
Quick Start Guide
Congratulations on your purchase of the SANbox 3050™ Fibre Channel switch. This Quick Start
Guide describes how to install and activate your SANbox 3050 switch using a Windows
workstation.
Prerequisites
• Workstation
• Operating systems:
• Windows NT/2000/2003
• Linux® Red Hat® 7.2
• Solaris® 2.8/2.9 CDE
• 256 MB memory
• 156 MB disk space
• 300 MHz processor
• Video card with 256 colors
• CD ROM drive, RS 232 serial port, RJ-45 Ethernet port
• Crossover cable to connect the workstation and the switch
• IP address, subnet mask, and gateway to assign to the switch
Switch Installation Procedure
Step 1. Verify the Package Contents
Step 2. Mount the Switch
Step 3. Install SFPs
Step 4. Apply Power to the Switch
Step 5. Install the SANbox Manager Application

2
Step 1. Verify the Package Contents
The SANbox 3050 Fibre Channel Switch is shipped with the following items:
1 SANbox 3050 Fibre Channel Switch
1Powercord
4 Rubber feet
2 Mounting brackets
8 Mounting screws
1CD
NOTE: Small Form-factor Pluggable (SFP) transceivers, if ordered, are packaged separately.
Step 2. Mount the Switch
You can mount the SANbox 3050 switch on a flat surface or in a rack.
❑For a surface mount, attach the rubber feet to the locations on the bottom of the switch
❑For a rack mount, fasten the brackets to
the switch using 2 screws on each
bracket as shown. Choose the holes in
the bracket to produce the desired set
back from the front of the cabinet. Place
the switch in a standard 19" rack and
fasten thebracket flanges to the rack with
two screws on each side.
Step 3. Install SFPs
An optical SFP is required for each switch port that will be connected to a device, device loop, or
another switch. Recommended SFP: Picolight® PL-XPL-VC-S23-11.
❑If SFPs were included in your shipment, install them now. To install an SFP transceiver,
insert the transceiver into the switch port and gently press until it snaps in place. The SFP
will fit only one way. If the SFP does not install under gentle pressure, flip it over and try again.

3
Step 4. Apply Power to the Switch
❑Attach the supplied power cable to the
switch and wall outlet or power strip.
Verify that the Input Power LED is on.
❑The switch runs its self tests and begins
normal operation – this may take a few
minutes. Verify that the Heartbeat LED is
blinking (once per second) and the
System Fault LED is NOT illuminated.
NOTE: The SB3050-XXX-E switch comes
complete with pre-configured zones for the
EMC ClARiiON AX100™. Follow the diagram
below to connect to your devices. If desired,
use the SANbox Manager Application to
perform advanced switch configuration.
Zone Name Switch Ports
Zone 1 1, 0
Zone 2 1, 4
Zone 3 2, 0
Zone 4 2, 4
Zone 5 3, 0
Zone 6 3, 4
Zone 7 7, 0
Zone 8 7, 4
Zone 9 5, 0
Zone 10 5, 4
Zone 11 6, 0
Zone 12 6, 4
INPUT
POWER LED
HEARTBEAT
LED
SYSTEM
FAULT LED
The pre-configured zone names and switch
port numbers are listed in the Pre-configured
AX100 Zones table.
Pre-configured AX100 Zone Table

4
Step 5. Install the SANbox Manager Application
To install the SANbox Manager application on a Windows workstation/server, perform the following
steps:
❑Insert the supplied CD into the CD ROM drive of the workstation/server.
NOTE: If the Welcome screen does not appear, browse the CD and run the installer program with
the following path: [CD ROM drive]\GUI\Windows_4.00.xx.xx.
❑In the Welcome screen, click SANbox Switch Manager.
❑In the License Agreement screen, click Agree.
❑Find the Installation File for the Windows operating system in the table, and click Install.
❑Follow the on-screen instructions to complete the software installation.
If you are using a Linux or Solaris workstation/server, mount the CD and run the following installer
programs based on your platform:
• Linux installer program: [CD ROM drive]/GUI/Linux_4.00.xx.xx
• Solaris installer program: [CD ROM drive]/GUI/Solaris_4.00.xx.xx
Congratulations!
You have successfully installed your QLogic SANbox 3050
Switch!
For technical support, visit our web site at support.qlogic.com, email us at [e-mail],
or call us at 952-932-4040. For more detailed installation instructions, see the SANbox 3050 Fibre
Channel Switch Installation Guide, located on the product CD or on the QLogic web site.
©QLogic Corporation. QLogic, SANbox, and SANbox Manager are trademarks or registered trademarks of QLogic Corporation. All other
trademarks are the property of their respective companies. Information supplied by QLogic is believed to be accurate and reliable. QLogic
Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to make changes
in product design or specifications.

QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656
949.389.6000 www.qlogic.com
50327-03 A
*50327-03A*