QSC USL JSD-60 User manual

USL JSD-60
User Manual
Cinema Processor

184050 Page 2

184050 Page 3
Table of Contents
1. Safety Notice 5
2. Legal Notices 8
3. Regulatory Compliance 8
4. Warranty 9
5. System Overview 10
5.1 System Description 10
5.2 Model Numbers 12
6. Specifications 13
7. Installation 16
7.1 Initial Power Up 16
7.2 System Hardware Mounting, Grounding and Ventilation 16
7.3 Eight Channel Analog Output 17
7.4 AES/EBU Output Rear Panel Connections (JSD-60LS or JSD-60DS) 18
7.5 Eight Channel Analog Crossover Output (JSD-60LX or JSD-60DX) 19
7.6 BLU link Output Rear Panel Connections (JSD-60LN or JSD-60DN) 20
7.7 Audio Input Connections 21
7.8 Analog Audio Output Connections 22
7.9 Automation Interface 23
8. Graphical User Interface Configuration 23
8.1 GUI Installation 24
8.2 Set IP Utility 24
9. System Operation 25
9.1 Front Panel 26
9.2 Automation 26
9.3 System Monitoring 26
Appendix A – Connector Pinouts 28
Appendix B – Automation Commands 37
Appendix C – System Restore and Power-Up Buttons 40
Appendix D – JSD-60 Accessories 42

184050 Page 4

184050 Page 5
1. Safety Notice
Safety Notices
Review the following safety precautions to avoid injury and prevent damage to this product. To
avoid potential risk, use this product only as specified and only for the purpose described in the
instruction manual.
To avoid fire and personal injury:
•Use the correct power cable. Use only the power cable provided. Make sure that the AC
power outlet is located near the product and is easily accessible.
•Use a correctly grounded power source. The safety ground is established through the
ground conductor in the power cable. To prevent electric shock, the ground conductor must
be intact.
•Observe source ratings. To avoid risk of fire or electric shock, the power source must be
100 – 240 VAC, 50 – 60 Hz.
•Do not operate with suspected failures. If you suspect there is damage or malfunction with
this product, call the factory.
•Do not attempt repair. Only a trained factory service person is authorized to repair this
product.
•Do not operate this product near heat sources. This product should not be located near
heat sources such as radiators, heat registers, or stoves.
•Provide proper ventilation. The recommended operating temperature range is between 0°
C and 40° C. The allowable humidity range is between 20% and 80%, non-condensing. The
cooling method is convection.
•Keep product surfaces clean and dry. Disconnect the power cable from the power source
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
•Do not push objects into openings of this product.Never insert objects into the product
through openings.
•Do not operate in wet or damp conditions.
•Do not operate in an explosive atmosphere.
•Inspect the power cable and all cables prior to use. Confirm that the power cable and other
interconnecting cables are free from damage.
•The appliance coupler (IEC connection) or the AC mains plug is the AC mains disconnect
and shall remain readily accessible after installation.
WARNING! TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
ATTENTION! AFIN D'ÉVITER TOUT INCENDIE OU UN CHOC ÉLECTRIQUE, N'EXPOSEZ
PAS CET ÉQUIPEMENT À LA PLUIE OU À L'HUMIDITÉ.
WARNUNG! SETZEN SIE DIESES GERÄT WEDER REGEN NOCH FEUCHTIGKEIT AUS,
UM BRÄNDE ODER STROMSCHLÄGE ZU VERMEIDEN.

184050 Page 6
Le Résumé de la Sécurité general Européen
Examinez les précautions de la sécurité suivantes éviter la blessure et prévenir le dégât à ce
produit. Éviter le risque potentiel, utilisez ce produit seulement comme a spécifié et seulement
car le but a décrit dans le manuel d’instructions.
Éviter Feu et Blessure Personnelle
•Utilisez le câble du pouvoir correct. Utilisezseulement le câble du pouvoir fourni. Assurez
que les AC font fonctionner le débouché est localisé près leproduit et est accessible
facilement.
•Utilisez une source du pouvoir correctement fondée.
•La terre du monde de la provision du pouvoir estétablie à travers le conducteur moulu dans
le câble du pouvoir. Éviter le potentiel de choc électrique, leconducteur moulu doit être
correct.
•Observez des estimations de la source. Pour éviterrisque de feu ou choc électrique, la
source du pouvoirdoit être 220–240 VAC 50 Hz.
•N’opérez pas ce produit avec toutes clôtures ouvertes ou enlevez.
•Évitez l’ensemble de circuits exposé. N’entreprenez pas ouvrir la provision du pouvoir parce
que sa certi-fication de la sécurité serait invalidée. La provision du pouvoir est un appareil
scellé non-réparable.
•N’opérez pas avec les échecs suspects. Si vous suspectez il y a le dégât ou mal fonctionner
avec ce produit, appelez l’usine.
•N’entreprenez pas réparation. Seulement une personne du service de l’usine compétente
est autorisée pour réparer ce produit.
•N’opérez pas ce produit sources de la chaleur proches. Ce produit ne devrait pas être
localisé desources de la chaleur proches tel que radiateurs, registres de la chaleur, poêles,
ou amplificateurs.
•Fournissez ventilation adéquate. La température dufonctionnement devrait être entre 0° C
et 40° C.
•L’humidité devrait être 20% et 80%. La méthode refroidissante est par convection et un
ventilateur interne.
•Gardez les surfaces du produit nettoient et sec.
•Déconnectez le câble du pouvoir de la source du pouvoir avant de nettoyer. N’utilisez pas
de nettoyeurs. liquides ou de nettoyeurs de l’aérosol utilisez un tissu humide pour nettoyer.
•Ne poussez pas d’objets dans ouvrir de ce produit.
•Jamais objets de l’encart dans le produit à travers ouvertures.
•N’opérez pas dans les conditions mouillées ou humides.
•N’opérez pas dans une atmosphère explosive.
•Prévenez le répandre des liquides sur les composants du système.
•Inspectez le câble du pouvoir et tous les câbles antérieur à usage. Confirmez que le câble du
pouvoir et autres interconnectant câbles sont libres de dégât.
•Le coupleur d'appareil (connexion CEI) ou la fiche secteur est la déconnexion du secteur et
doit rester facilement accessible après l'installation.

184050 Page 7
Allgemeine Europäische Sicherheitszusammenfassung
Beachten Sie die folgenden Sicherheishinweise um Verletzungen zu vermeiden und Schaden an
diesem Produkt zu verhindern. Um potentielle Risiken zu vermeiden, benutzen Sie dieses
Produkt nur wie beschrieben und nur für den in der Bedienungsanleitung identifizierten Zweck.
Um Feuer und Verletzung zu vermeiden:
•Benutzen Sie das korrekte Netzkabel. Nur das bereitgestellte Netzkabel soll benutzt werden.
Stellen Sie sicher, daß die Wechselstromsteckdose in der Nähe des Produktes und leicht
zugänglich ist.
•Benutzen Sie eine korrekt geerdete Stromquelle. Die Erdung des Netzteils wird durch den
Erdleiter im Stromkabel hergestellt. Um das elektrische Schockrisiko zu vermeiden muß der
Erdleiter korrekt sein.
•Beachten Sie die Nennwerte der Stromquelle. Um das Risiko von Feuer oder elektrischem
Schock zu vermeiden muß eine 100-240 VAC 50-60 Hz Stromquelle benutzt werden.
•Betreiben Sie das Gerät nicht wenn Fehlerverdacht besteht. Wenn Sie vermuten, daß das
Gerät defekt oder beschädigt ist, kontaktieren Sie den Hersteller.
•Versuchen Sie keine Reparatur. Nur ein vom Hersteller ausgebildeter Servicetechniker ist
befugt dieses Produkt zu reparieren.
•Betreiben Sie dieses Produkt nicht in der Nähe von Wärmequellen. Dieses Produkt sollte
nicht in die Nähe von Wärmequellen, wie zum Beispiel Heizungen, Herden und
Warmluftöffnungen gestellt werden.
•Erlauben Sie für ausreichende Belüftung. Die Betriebstemperatur sollte zwischen 0° C und
40° C sein, die Luftfeuchtigkeit sollte 20% bis 80% nicht kondensierend, betragen. Luftzufuhr
erfolgt durch Umluft und ein internes Gebläse.
•Halten Sie die Produktoberflächen sauber und trocken. Ziehen Sie das Netzkabel aus der
Steckdose vor der Reinigung. Benutzen Sie keine flüssigen oder Druckluft Reiningungsmittel.
Benutzen Sie ein feuchtes Tuch zum Reinigen.
•Schieben Sie keine Gegenstände in die Öffnungen dieses Produktes.
•Betreiben Sie dieses Produkt nicht in nassen oder feuchten Bereichen.
•Betreiben Sie dieses Produkt nicht in explosiven Bereichen.
•Inspizieren Sie das Netzkabel und all anderen Kabel vor Benutzung. Bestätigen Sie, daß das
Netzkabel und andere Kabel unbeschädigt sind.
•Betreiben Sie dieses Produkt nicht wenn es geöffnet oder Abdeckungen entfernt worden
sind.
•Vermeiden Sie ungeschützte Schaltkreise. Öffnen Sie das Netzteil nicht, da sonst die
Sicherheitszulassung ungültig würde. Das Netzteil ist ein unreparierbares luftdicht
verschlossenes Gerät.
•Verhindern Sie das Verschütten von Flüssigkeiten auf die Systembestandteile.
•Der Gerätestecker (IEC-Anschluss) oder der Netzstecker ist der Netztrenner und muss
nach der Installation frei zugänglich bleiben.

184050 Page 8
2. Legal Notices
Manufactured under license from Dolby Laboratories®. Dolby® and the Double-D symbol are
trademarks of Dolby Laboratories®.
Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other
U.S. and worldwide patents issued & pending. DTS, the Symbol, & DTS and the Symbol together
are registered trademarks & DTS Digital Surround and the DTS® logos are trademarks of DTS,
Inc. Product includes software. © DTS®, Inc. All Rights Reserved. The JSD-60 includes
technology used under license from Harman International Industries.
3. Regulatory Compliance
FCC Part 15, Subpart B
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference
at the user’s own expense.
Proper Disposal
In conformance with the Directive, at end of life this product should be either sent to an
appropriate recycling facility for disassembly and recycling or returned to the supplier. Under
no circumstances should this product be deposited in a landfill for disposal.
Lifetime
This product can be expected to operate for 10 years.
Storage
-20 to 70°C, 5% to 95% relative humidity (non-condensing).

184050 Page 9
NOTE: The JSD-60 Cinema Processor is manufactured in the USA.
Serial Number Date Code Explanation
The product’s serial number includes information that identifies the week of manufacture. Use
the diagram below to interpret the date code.
4. Warranty
For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com.
Para una copia de la garantía limitada de QSC, visite el sitio web de QSC, en www.qsc.com
Pour obtenir une copie de la garantie limitée de QSC, visitez le site de QSC à www.qsc.com
Eine Kopie der beschränkten QSC-Garantie finden Sie auf der QSC Webseite unter www.qsc.com.
如果您想要QSC有限保修的複印本，请造访QSC音频产品的网站www.qsc.com
Для получения копии ограниченной гарантии QSC посетите веб-сайт QSC, расположенный по
адресу www.qsc.com.
www.qsc.com تﺎﺟﺗﻧﻣﻠﻟ ﺔﯾﺗوﺻﻟا ﻰﻠﻋ QSC ﺔﻛ لشوﻲﻧ _ مﻗ ةرﺎﯾزﺑ ﻊﻗوﻣﻟا اإكﻠﻟ ت،QSC لوﺻﺣﻠﻟ ﻰﻠﻋ ﺔﺧﺳﻧ نﻣ نﺎﻣﺿﻟا
دودﺣﻣﻟا صﺎﺧﻟا

184050 Page 10
5. System Overview
5.1 SYSTEM DESCRIPTION
The JSD-60 cinema sound processor is specially designed for digital cinema applications. Low
noise and low distortion 96 kHz processing ensures superb presentations. In addition to the six
standard formats. A user-configurable format button can be configured to support a variety of
existing and future formats. It may also be used to duplicate an existing format but at a
different fader level to simplify desired volume changes between content types. The front panel
display shows the current fader level, the format name (which is user configurable), and the
audio level on each audio output. The built-in bypass audio circuitry ensures that the
presentation goes on in the unlikely event of a system failure.
The JSD-60 is “automation friendly.” It features the standard DB25 parallel automation
interface, an RS-232 (EIA232) interface, and Ethernet. The Ethernet interface accepts five
simultaneous TCP connections to allow control by a digital cinema server and other equipment
while simultaneously being monitored over another TCP connection.
The graphical user interface (GUI) runs on Windows XP®, Windows 7®, Windows 8®, and
Windows 10® operating systems. It allows for complete system configuration, monitoring, and
firmware updates over USB, Ethernet, or RS-232. The JSD-60 graphical user interface simplifies
installation by including sound pressure level measurement and automatic equalization. System
monitoring, control, and firmware update functions are also available on a standard web
browser.
The JSD-60 includes a precision 1/3 octave RTA that uses the filters specified in ANSI S1.11-
1986. The JSD-60 also does sound pressure measurements using the C-weighted filter specified
in ANSI S1.4-1983. The RTA and SPL meter can be used to equalize an auditorium manually or
automatically.
The JSD-60 includes an automatic equalization feature (auto-EQ). Auto-EQ uses user-defined
microphone calibration files and standard or user-defined equalization curves to automatically
adjust the graphic equalizer on each channel.
The JSD-60 supports graphic and parametric equalization methods with bass management.
The JSD-60 is also “diagnostic friendly.” The system logs the last 15,000 events (format changes,
level changes, internal temperature, loss of AES/EBU audio, etc.) to internal flash memory. Log
data can be reviewed on the GUI or the web interface. Current operational status, including
selected format, fader level, and measured audio output levels, is available on the GUI and on
the web interface. The current status of the system is also available over SNMP (Simple
Network Management Protocol).

184050 Page 11
An optional plug-in module decodes Dolby Digital® and DTS® encoded content.
The HI and VI-N outputs are configurable on a per-format basis.
An optional crossover card supports bi-amp of three screen channels and provides two LFE
outputs.
An optional AES/EBU output card provides 12 channels of AES/EBU. The AES/EBU outputs are
on two RJ45 connectors and provide full range or bi-amp screen channels plus the surround
channels and two LFE outputs.
An optional BLU link output card provides 12 channels on a Harman BLU link loop. The BLU link
loop is driven by two RJ45 connectors and provides full range or bi-amp screen channels plus
the surround channels and two LFE outputs. Note that the JSD-60 is the BLU link loop clock
master and runs the loop at 96 kHz.
A user configurable mixer routes audio as required for the specific auditorium. Supported
auditorium configurations include 5.1, 7.1DS, 7.1SDDS, and drive-in.

184050 Page 12
5.2 MODEL NUMBERS
An optional output board is part of the unit’s assembly that supports a variety of output
configurations. These are listed in the table below.
The various JSD-60 options are identified by model number suffixes as shown in the tables
below. The first letter identifies input options such as the presence or absence of Dolby Digital®
and DTS® decoding. The second letter indicates the type of output. Note that all units have
analog HI/VI-N in addition to the outputs listed in the following tables:
A JSD-60DX has eight AES/EBU input channels, Dolby Digital® and DTS® decoding for alternative
content with bi-amp analog outputs.
First Suffix
Letter
Description
USL Module Part
Number
L
8 channel AES/EBU input, no Dolby Digital® or DTS®
decode
N/A
D
8 channel AES/EBU input, Dolby Digital® and DTS®
decode for alternative content
DI-84
Second Suffix
Letter
Description
USL Module Part
Number
None
8 channel analog output
N/A
N
BLU link output
JSDN-60
S
AES/EBU output
JSDS-60
X
8 channel analog output with bi-amp for three screen
channels and two LFE outputs
XTD-60

184050 Page 13
6. Specifications
Features
A processor specially designed for Digital Cinema applications. Low noise and low distortion
processing ensures superb presentations. In addition to six standard formats, the JSD-60 offers
a fully configurable optional format to address such details as audio level changes and three or
five stage channels. Built-in bypass audio circuitry ensures that the presentation goes on.
Audio Inputs
•PA/Cal Microphone – XLR and ¼”, 0.7 mV sensitivity. Switchable phantom power: 12 V
balanced, 9V unbalanced, or off.
•Non-Sync analog input – RCA 75 mV to 4.775 V.
•Six Channel analog input – DB25F 300 mV.
•COAX – RCA: PCM with optional Dolby Digital® and DTS® decoding.
•TOSLINK – Optical PCM with optional Dolby Digital® and DTS® decoding.
•AES/EBU – eight Channel 48-96 kHz sample rates.
Analog Audio Outputs – Accessibility
•Hearing Impaired – User selectable input channel mix. 300 mV mono balanced.
•Visually Impaired - Narrative– User selectable input channel mix. 300 mV mono balanced.
Eight Channel Analog Audio Outputs (JSD-60L and JSD-60D)
Eight Channels Balanced 300 mV adjustable (L, C, R, Ls, Rs, LFE 1, Lc/Lrs, Rc/Rrs).
Nine Channel Bi-amp Analog Audio Outputs (JSD-60LX and JSD-60DX)
•12 outputs, Balanced 300 mV adjustable (L, C, R, Ls, Rs, LFE 1, LFE 2, Lc/Lrs, Rc/Rrs, Lh, Rh,
Ch). Configurable as 5.1, 7.1 broadband, or bi-amp three screen channels.
Nine Channel Bi-amp AES/EBU Audio Outputs (JSD-60LS and JSD-60DS)
•12 outputs, on six AES/EBU pairs on two RJ45 connectors (L, C, R, Ls, Rs, LFE 1, LFE 2, Lc/Lrs,
Rc/Rrs, Lh, Rh, Ch). 96 kHz sample rate. Configurable as 5.1, 7.1 broadband, or bi-amp three
screen channels.
Nine Channel Bi-amp BLU link Audio Outputs (JSD-60LN and JSD-60DN)
•12 outputs, on two RJ45 connectors (L, C, R, Ls, Rs, LFE 1, LFE 2, Lc/Lrs, Rc/Rrs, Lh, Rh, Ch).
96 kHz sample rate. Configurable as 5.1, 7.1 broadband, or bi-amp three screen channels.
Communication Ports
•DB25F pulse automation.
•Serial control – RS-232.
•USB for laptop setup.
•Ethernet 10/100 - RJ45.

184050 Page 14
Front Panel Interface
•Eight buttons: COAX, TOSLINK, DIGITAL 8 CH, OPTION, ANALOG 6 CH, NON/SYNC, MIC, and
MUTE.
•Main Fader – 0–10 used for main audio and bypass audio.
•Front panel displays fader level and selected format. Bar graph displays output levels
including high and low bands when operating in bi-amp.
•USB connector.
•Power switch and power supply status LEDs. Turning power off activates bypass mode.
Format Selection
•Digital (COAX, TOSLINK, eight Channel AES/EBU).
•Analog (6 channel, Non-Sync, and Microphone).
•Option (Configurable in software, e.g., digital 8 channel, COAX, TOSLINK, analog six channel,
Non/Sync, and microphone).
Rear Panel Connectors – Main Chassis
•PA/Calibration Microphone – XLR / ¼" phone jack.
•Six Channel Analog – DB25F.
•Non/Sync – two RCA jacks.
•Hearing Impaired and Visually Impaired - Narrative – pluggable Phoenix connector.
•COAX – RCA jack with transformer input
•TOSLINK – Optical.
•8 Channel Digital AES/EBU – DB25F and RJ45.
•Removable Memory Card – SD compatible.
•Serial Control – RS-232 on DB9F.
•Pulse Automation – DB25F.
•10/100M Ethernet – RJ45.
•DC 12V Power Connector – 5 mm with 2.5 mm pin.
•AC Power – IEC socket. 100-240 VAC, 50/60 Hz, 18 W typical.
•Eight Channel Audio Output - DB25M. Eight balanced outputs for full range or low band (if
crossover option installed).
•Crossover Audio Output - DB25M (crossover option only). Balanced outputs for left, center,
and right high band plus LFE2.
•AES/EBU Audio Output – Two RJ45 connectors (AES/EBU output option only). Six AES/EBU
pairs: left low, left high, center low, center high, right low, right high, Ls, Rs, Lrs, Rrs, LFE,
LFE2. When bi-amp mode not selected, low band outputs become full range.
•BLU link Audio Output – Two RJ45 connectors (BLU link option only). Drives 96 kHz BLU link
loop as master providing left low, left high, center low, center high, right low, right high, Ls,
Rs, Lrs, Rrs, LFE, LFE2. When bi-amp mode not selected, low band outputs become full
range.

184050 Page 15
Processing
•96 kHz processing.
•One-third octave and eight parametric equalization bands on all channels except LFE 1, LFE
2, HI, and VI-N.
•Parametric equalizers on LFE.
•Synchronization delays for all inputs.
•Surround delays for all surround channels.
•Optional Internal crossovers. Crossovers support bi-amp with three screen channels plus
individual parametric equalization and two LFE outputs. Crossover includes a speaker library
and allows for user defined speaker systems.
Bypass Mode
In an emergency situation, the JSD-60 can be switched off, automatically enabling the bypass
circuitry. Front panel buttons, LEDs, display, and fader will still function, allowing the operation
of the unit in various analog and digital formats. Final output is a monophonic signal fed to the
left and right channels. Bypass circuitry only drives analog outputs, not AES/EBU or BLU link
outputs. Note: The 12 VDC bypass power supply must be connected for this functionality.
Graphical User Interface
The JSD-60 Graphical User Interface (GUI) operates under Windows XP, Windows 7, Windows 8,
and Windows 10. It communicates with one or more JSD-60 systems simultaneously over USB,
Ethernet, or RS232. The GUI is used for system configuration including auditorium equalization
(both manual and automatic equalization).
Dynamic Range: Typically 105 dB.
Power Requirements: 100–240 VAC, 50/60 Hz, 30 watts maximum (18 watts typical).
Dimensions: Standard 1U rack-mount chassis.
Agency Approvals: UL, cUL, CE and FCC.

184050 Page 16
7. Installation
7.1 INITIAL POWER UP
A quick power-up test of the JSD-60 is suggested before mounting it in the equipment rack and
wiring it up. This test can quickly detect shipping or other damage.
•Turn the AC power switch off.
•Using the supplied AC line cord or one appropriate for the installation location (the power
supply is a universal input supply 100-240 VAC, 50/60 Hz), connect the JSD-60 to the AC
mains.
•Connect the supplied 12 VDC bypass power supply to the bypass power input on the rear
panel of the JSD-60 and plug it in to the AC line. The front panel “Bypass Mode” LED should
flash, the bypass power LED should light, and one of the format buttons should light.
•Press each of the format buttons and the mute button, one after another. The appropriate
button should light.
•Rotate the fader in each direction and verify that the fader level on the display changes.
•Turn on the AC power switch. All the green power LEDs on the bottom right of the front
panel should light. The “Bypass Mode” LED should stop flashing.
•Press each of the format buttons and the mute button, one after another. The appropriate
button should light and the display should show the selected format. Note that the format
button LEDs for digital formats will flash when no digital input is provided.
•Press the mute button verifying that its LED toggles each time the button is pressed.
•Rotate the fader in each direction verifying that the fader numbers on the display change
7.2 SYSTEM HARDWARE MOUNTING, GROUNDING AND VENTILATION
The JSD-60 is designed to mount in a standard 19 inch (482.6 mm) rack and is one rack unit high
(1.75 inches, 44.45 mm). The JSD-60 should be mounted at about eye level in the equipment
rack for optimum display contrast and visibility. We recommend vented panels (USL part
number VP-1) above and below the JSD-60 whenever space permits. Mounting the unit
immediately above a major heat-producing component, such as a power amplifier, is not
recommended. Equipment mounted immediately above the JSD-60 should not be more than
9 inches (225 mm) deep to ensure adequate airflow through the top cover ventilation holes on
the JSD-60. The JSD-60 includes a three-prong grounding plug and a three-wire power cord to
accommodate a safe ground path from the chassis to the electrical system ground. Defeating
this ground by removing the ground prong is not recommended.

184050 Page 17
7.3 EIGHT CHANNEL ANALOG OUTPUT
1. Power entry Module – Accepts IEC-type line cord from 100–240 VAC power source. Also
contains a 500 mA Slo-Blow 5×20 mm fuse.
2. Bypass Power Supply – 12 VDC at 1.25 A.
3. RS-232 on a DE9F connector for communications with GUI or automation.
4. SD Card – Stores a backup copy of unit configuration. Can also be used to transfer settings
to another unit or read by the GUI to download to a connected unit.
5. AES/EBU input connector (RJ45) – parallel connections to the DB25F to the right.
6. Ethernet connector (RJ45) – Network communications with GUI, web browsers,
automation, etc.
7. AES/EBU input connector (DB25F) – Eight channels, DMA8 pin out.
8. Automation DB25F Connector – Receives automation pulses from other system
components. Ten Control input lines with ground and 5 V power provided to support a
standard pulse to ground system. The 5 V output can power a JSDV-80 remote volume
control that pulses control lines 9 and 10.
9. COAX - RCA connector for S/PDIF PCM or optional DTS® and Dolby Digital® decoding.
10. TOSLINK Port – Optical Fiber input (PCM) with optional DTS® and Dolby Digital® decoding.
11. Hearing Impaired/Visually Impaired-Narrative outputs.
12. Eight Channel Analog output provides six fixed outputs (L, C, R, LFE, Ls, Rs) and two that can
be set up as either Lc/Rc or Lrs/Rrs. Other output configurations, such as drive in, are
supported.
13. Six Channel Analog Input on DB25F – Balanced line inputs.
14. Non Sync (N/S) connectors – L and R analog inputs, RCA type connectors.
15. Public Address and Real Time Analyzer microphone phantom power supply selector, 12 V
balanced, 9 V unbalanced, and off.
16. Public Address and Real Time Analyzer microphone – XLR and ¼ stereo jack with
configurable phantom power.

184050 Page 18
7.4 AES/EBU OUTPUT REAR PANEL CONNECTIONS (JSD-60LS OR JSD-60DS)
1. Power entry Module – Accepts IEC-type line cord from 100–240 VAC power source. Also
contains a 500 mA Slo-Blow 5×20 mm fuse.
2. Bypass Power Supply – 12 VDC at 1.25 A.
3. RS-232 on a DE9F connector for communications with GUI or automation.
4. SD Card – Stores a backup copy of unit configuration. Can also be used to transfer settings
to another unit or read by the GUI to download to a connected unit.
5. AES/EBU input connector (top RJ45) – parallel connections to the DB25F to the right.
Ethernet connector (bottom RJ45) – Network communications with GUI, web browsers,
automation, etc.
6. AES/EBU input connector (DB25F) – Eight channels, DMA8 pin out.
7. Automation DB25F Connector – Receives automation pulses from other system
components. Ten control input lines with ground and 5 V power provided to support a
standard pulse to ground system. The 5V output can power a JSDV-80 remote volume
control that pulses control lines 9 and 10.
8. COAX - RCA type connector (PCM) with optional DTS® and Dolby Digital®decoding.
9. AES/EBU Outputs 1-8
10. TOSLINK Port – Optical Fiber input (PCM) with optional DTS® and Dolby Digital® decoding.
11. Hearing Impaired/Visually Impaired-Narrative outputs.
12. AES/EBU Outputs 9-12
13. Eight channel analog outputs. These outputs are active whether the AES/EBU output card is
present or not. If the JSD-60 is configured for bi-amp, the screen channel outputs will be the
low band.
14. Six channel analog input on DB25F – Balanced line inputs.
15. Non Sync (N/S) connectors – L and R analog inputs, RCA type connectors.
16. Public address and real time analyzer microphone phantom power supply selector, 12 V
balanced, 9 V unbalanced, and off.
17. Public address and real time analyzer microphone – XLR and ¼” stereo jack with
configurable phantom power.

184050 Page 19
7.5 EIGHT CHANNEL ANALOG CROSSOVER OUTPUT (JSD-60LX OR JSD-60DX)
12346
57810 12 14 15 16 17 18 19
911 13
1. Power entry Module – Accepts IEC-type line cord from 100–240 VAC power source. Also
contains a 500 mA Slo-Blow 5×20 mm fuse.
2. Bypass Power Supply – 12 VDC at 1.25 A.
3. RS-232 on a DE9F connector for communications with GUI or automation.
4. SD Card – Stores a backup copy of unit configuration. Can also be used to transfer settings
to another unit or read by the GUI to download to a connected unit.
5. AES/EBU input connector (RJ45) – parallel connections to the DB25F to the right.
6. Ethernet connector (RJ45) – Network communications with GUI, web browsers,
automation, etc.
7. AES/EBU input connector (DB25F) – Eight channels, DMA8 pin out.
8. Automation DB25F Connector – Receives automation pulses from other system
components. Ten Control input lines with ground and 5 V power provided to support a
standard pulse to ground system. The 5 V output can power a JSDV-80 remote volume
control that pulses control lines 9 and 10.
9. Crossover bypass output levels for high and low bands.
10. COAX - RCA type connector (PCM) with optional DTS® and Dolby Digital®decoding.
11. Crossover balanced stage high band (L, C, R) and LFE 2 outputs.
12. TOSLINK Port – Optical Fiber input (PCM) with optional DTS® and Dolby Digital® decoding.
13. Crossover bypass frequency and mode selection switches.
14. Hearing Impaired/Visually Impaired-Narrative outputs.
15. Eight channel analog outputs. Low band on screen channels, full range on surround
channels.
16. Six channel analog input on DB25F – Balanced line inputs.
17. Non Sync (N/S) connectors – L and R analog inputs, RCA type connectors.
18. Public Address and Real Time Analyzer microphone phantom power supply selector, 12 V
balanced, 9 V unbalanced, and off.
19. Public Address and Real Time Analyzer microphone – XLR and ¼” stereo jack with
configurable phantom power.

184050 Page 20
7.6 BLU LINK OUTPUT REAR PANEL CONNECTIONS (JSD-60LN OR JSD-60DN)
1. Power entry module – Accepts IEC-type line cord from 100–240 VAC power source. Also
contains a 500 mA Slo-Blow 5×20 mm fuse.
2. Bypass Power Supply – 12 VDC at 1.25 A.
3. RS-232 on a DE9F connector for communications with GUI or automation.
4. SD Card – Stores a backup copy of unit configuration. Can also be used to transfer settings
to another unit or read by the GUI to download to a connected unit.
5. AES/EBU input connector (Top RJ45) – parallel connections to the DB25F to the right.
Ethernet connector (Bottom RJ45) – Network communications with GUI, web browsers,
automation, etc.
6. AES/EBU input connector (DB25F) – Eight channels, DMA8 pin out.
7. Automation DB25F Connector – Receives automation pulses from other system
components. Ten control input lines with ground and 5 V power provided to support a
standard pulse to to ground system. The 5 V output can power a JSDV-80 remote volume
control that pulses control lines 9 and 10.
8. Monitor analog output – Balanced analog audio of a user selected BLU link channel.
9. COAX - RCA type connector (PCM) with optional DTS® and Dolby Digital® decoding.
10. BLU link output connector – Drives the input of the next device in the BLU link loop.
11. TOSLINK Port – Optical Fiber input (PCM) with optional DTS® and Dolby Digital® decoding.
12. Hearing Impaired/Visually Impaired-Narrative outputs.
13. BLU link input connector – Driven by the output of the previous device in the BLU link loop.
14. Eight channel analog outputs. Low band on screen channels, full range on surround
channels.
15. Six channel analog input on DB25F – Balanced line inputs.
16. Non Sync (N/S) connectors – L and R analog inputs, RCA type connectors.
17. Public address and real time analyzer microphone phantom power supply selector, 12 V
balanced, 9 V unbalanced, and off.
18. Public address and real time analyzer microphone – XLR and ¼” stereo jack with
configurable phantom power.