Qtx KAD-2BT User manual

KAD-2BT
DIGITAL STEREO AMPLIFIER with BLUETOOTH
Item ref: 103.122UK
User Manual
Specifications:
Power Supply 230Vac, 50Hz (IEC)
Output Impedance 4 - 8Ω
Output Power (8Ω) 2 x 25W rms / 2 x 40W max. (EIAJ Standard @ 1kHz 10% THD)
Output Power (4Ω) 2 x 35W rms / 2 x 55W max. (EIAJ Standard @ 1kHz 10% THD)
Input sensitivity: line 380mV
Input sensitivity: mic 15mV
Dimensions 200 x 200 x 65mm
Weight 1.6kg
Version 2.1

103.122UK Manual
Introduction
Thank you for choosing the QTX KAD-2BT stereo amplifier. This compact class D digital amplifier is
capable of delivering a powerful 55W max output per channel. With 4 selectable inputs, 2 mic inputs and
various controls, this is a great multipurpose amplifier for both domestic and commercial use.
Product layout:
1. Power switch
MEDIA PLAYER:
2. SD card slot
3. USB memory stick slot
4. Previous track/hold for Rewind
5. Play/Pause
6. Next track/hold for Fast-Forward
7. Input selection
8. Input display
MAIN UNIT:
9. Volume control
10. 6.3mm jack microphone input
11. Aux input, 3.5mm jack socket
12. Rotary input selector
13. Input bass level control
14. Input treble level control
15. Microphone input echo effect
16. Microphone input tone control
17. Microphone input level control
18. RCA stereo line inputs
19. Spring clip for FM antenna
20. Spring clip speaker output
21. IEC mains input
Impedance Matching:
KAD-2BT is capable of 4-16Ω impedance output if more than one speaker is to be connected to the
amplifier per channel. Please ensure the total impedance of the speakers are within the range.
Speakers can be wired in two different ways, in parallel or in series. The total impedance can be worked
out by the following formulas for the two different ways of wiring:
Parallel Connection - 1/Rtotal = 1/R1+ 1/R2+ 1/R3…….

103.122UK Manual
Series Connection - Rtotal = R1+ R2+ R3…….
Installation:
Before installation, please ensure power is switched off and mains unpluged from the wall to avoid
damage to equipment and installer.
Wire speakers to the amplifier as shown above, ensure the positive and negative terminals are wired
correctly. Audio input on the back is through 3 pairs of RCA connectors, ensure left and right signals are
correct for stereo output. Finally insert the IEC plug and connect the unit to the mains. Before switching
on, always ensure the master volume is set at the lowest point to avoid power surge damage to the unit
or speakers. Adjust the volume accordingly to an appropriate listening level.
Media Player:
KAD-2BT has a built in media player which functions as an MP3 player, FM tuner and Bluetooth receiver.
To use turn the input selector to media player.
MP3 Player –MP3 files can be played through an SD card or USB stick. Plug in the memory device and
media will automatically start playing. Alternatively press Mode button until “USB” is displayed on the
screen. To make a selection, press for previous or for next song respectively (press and hold for
reverse or press and hold for fast-forward). For play and pause press the button.
Bluetooth –for Bluetooth connection press MODE button until “BT” is displayed on the screen. From
your Bluetooth search function (please refer to device manual for instructions) look for “KAD-2BT” to pair
with, you should hear a tone once successfully connected. Step through tracks on the playback device
using the or buttons. For play and pause press the  button.
FM radio –for FM radio press MODE button until “FM” is displayed on the screen. Press the play and
pause  button to intiate search function through FM frequencies, all searched radio stations will be
stored (up to 99 stations). After the search is complete, it will automatically select the station on the
lowest frequency. Press the or buttons to step through the tuned stations.

103.122UK Manual
Troubleshooting
No Power
Check mains is switched on and power lead is in good condition and fully
inserted into the wall socket.
Check IEC plug is fully inserted into the amplifier on the back.
Check power switch is switched on on the amplifier.
Check if the fuse is faulty. If the fuse blows too frequently, stop use of
device immediately and refer to qualified personnel for repair.
No Music output
Check the input connection lead is fully inserted on both amplifier and
source.
Check the correct input is selected.
Check the audio source is playing.
Check volume is turn up on both amplifier and audio source
Check speaker cable is not damaged and connected properly on both
amplifier and speakers.
Check for any loose strands on the speaker that might short together the
positive and negative terminal, this will trigger the short circuit protection.
No Mic output
Check Mic is switched on.
Check Mic volume is turned up on the amplifier.
Check if Mic requires phantom power.
Check if Mic is working properly on another device.
Low output
Check speaker polarity is connected correctly.
Check audio source/media player volume is turned up.
Check impedance of the speaker/s is within the range.
Distorted output
Check output volume is not too high on both audio source and amplifier.
Check for damage on speaker cable and connection leads.
Check amplifier, audio device, speaker and connection cables are not near
any mains power cable or large inductive appliances such as a fridge.
Check location of the Bluetooth device is within the reception range of the
amplifier. Range may be significantly reduced in areas where a large number
of electronic / wireless devices are present.
Unable to connect to
Bluetooth
Check Bluetooth device function is switched on.
Restart both amplifier and Bluetooth device.
Unable to play
USB/SD
Ensure all files are saved on the root level and not hidden in folders.
Ensure audio files are saved in MP3 format.
FM radio not working
Ensure amplifier is not located close to any electronic devices e.g. large
transformers, fridges or microwaves.
Ensure volume on amplifier and media player are turned up.
Check the condition of the FM antenna.
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2018. AVSL Group Ltd