Qtx DM-X4 User manual

DM-X4
Mini DMX PAR Controller
Item ref: 154.096UK
User Manual

154.096UK User Manual
Introduction
Thank you for choosing the DM-X4 mini DMX PAR controller as part of your lighting control system.
This unit is designed to control DMX PAR fixtures with RGB or RGBW colour mixing.
Please read these instructions to gain the best results from this item and avoid damage through misuse.
Unpacking
Your DM-X4 should reach you in good condition and should be supplied with an appropriate mains adaptor.
If there are any signs of damage or items missing from the packaging, contact your dealer immediately.
Warning
To prevent risk of fire or electric shock, do not expose any components to rain or moisture.
Avoid any impact or extreme pressure to the housing or control surface.
No user serviceable parts inside - do not open the case. Refer all servicing to qualified service personnel.
Placement
The DM-X4 may be free standing on a stable surface or wall mounted by either hanging on screws with the
rear punch-holes or flush-mounting with the 4 front mounting holes.
Safety
Check for correct mains voltage before connecting the D.C. adaptor
Ensure DMX leads are good condition with no short connections or damaged plugs
Cleaning
Use a soft dry or slightly damp cloth to clean the casing. Do not use strong solvents
Periodically clear any debris from fader slots with a soft brush
Panel Layouts
1. RGBW channel faders
2. Group buttons
3. Channel Mode button & indicators
4. Run Mode button
5. Blackout button
6. Strobe button
7. Mix fader
8. MAC slider
9. Speed control
10. Strobe Speed/Sound Sensitivity slider
11. DMX out XLR
12. D.C. input jack
13. Power switch

154.096UK User Manual
Setting up
Connect all PAR lights to be controlled in a chain from DMX outputs to DMX using a good quality DMX leads
(XLRF-XLRM) and connect the DMX OUT connector (11) on the DM-X4 to the DMX input of the first PAR
light in the chain. Various DMX PAR lights may have different channel allocations and the DM-X4 can be set
to one of 6 modes to control these. The chart below shows the 6 modes with channel fader allocations.
Mode
F1
F2
F3
F4
For cans with type of DMX allocation
RGB
Red
Green
Blue
-
RGB cans
RGBD
Red
Green
Blue
Master
RGB cans with CH4 as Master Dimmer
RGBW
Red
Green
Blue
White
RGBW cans
RGBWD
Red
Green
Blue
Master
RGBW cans with CH5 as Master Dimmer
DRGB
Master
Red
Green
Blue
RGB cans with CH1 as Master Dimmer
DRGBW
Master
Red
Green
Blue
RGBW cans with CH1 as Master Dimmer
Note: for RGBW lights in 5-channel modes, Master dimmer and White are combined to a single fader.
Select the correct mode to match the type of PAR lights to be controlled. The above table gives examples of
channel allocation when they are set to start address A001. Remember that there may be a choice of
modes on each type of PAR light and it is best to set all cans to a similar DMX mode. Selecting a mode that
does not match the DMX allocation of the fixture(s) may give unexpected and confusing results.
In addition, the DM-X4 can control 4 groups of lighting fixtures separately via the four Group buttons (2).
Each group of PAR lights should be set with the relevant start address as shown below.
Group
DMX start address
Pressing the “1-10” Group button, engages Group 1
1
1
Pressing the “11-20” Group button, engages Group 2
2
11
Pressing the “21-30” Group button, engages Group 3
3
21
Pressing the “31-40” Group button, engages Group 4
4
31
Multiple groups can be selected together to control simultaneously
Groups that are selected are indicated by a blue flashing LED and any controls from the DM-X4 will affect
the group(s) selected. This feature makes a multi-zone light show possible with selected groups operating
from auto programs or sound-activated (see below) and others with manual control or static colour.
Operation
Connect the supplied mains adaptor to the DC input of the DM-X4 (12) and switch the power on (13)
For the selected group(s), moving the channel faders controls the amount of red, green, blue, and white
light output of DMX PAR fixtures. When mixing RGB and RGBW fixtures together within a group, it is
advised to set the DM-X4 to RGB mode so that each fixture produces the same shade.
In addition to the 4 channel faders, the DM-X4 has a MIX fader (7) which allows fast access to colour mixes
in a single movement.
Colour changing sequences are available by selecting “AUTO” on the Run Mode button (4) and moving the
MAC slider (8) to one of the 8 internal programs (MAC1 –MAC8). The speed of the selected program is
governed by the Speed Control slider (9) with step intervals from 0.1sec to 30sec.

154.096UK User Manual
Alternatively, selecting “SOUND” on the Run Mode button will engage sound-activated mode, which makes
colour jumps to a music beat detected by the internal microphone. The sensitivity of the internal
microphone is controlled via the Strobe Speed/Sound Sensitivity slider (10).
For strobe effects, pressing the strobe button will perform a white (RGB mix) flashing sequence with speed
governed by the Strobe Speed/Sound Sensitivity slider (10). Releasing the button reverts lights back to the
previous state.
To switch of all lights, a latching Blackout button (5) sets all DMX channels to zero value, indicated by a
flashing LED.
When not in use for long periods, switch off power and disconnect the adaptor from the mains.
Specifications
Power supply
9-12Vdc, 300mA adaptor (supplied)
Controls
R, G, B, W/D, mix, MAC, speed, strobe/sensitivity
Mode(s)
RGB, RGBD, RGBW, RGBWD, DRGB, DRGBW
Output
DMX (XLRF)
Dimensions
200 x 109 x 55mm
Weight
780g
Troubleshooting
No power
Check mains voltage is correct and outlet is switched on
Check mains adaptor is OK and connected properly
No DMX control
Check DMX leads are OK and connected correctly
Check correct group button is selected (flashing LED)
Check that light fixture is set to the correct DMX start address
DMX control not
working as expected
Check that the correct mode is selected for the type of fixture
Check that light fixture is set to the correct DMX mode
Check that light fixture is set to the correct DMX start address
DISPOSAL:
Please disposal of the unserviceable device according to the current statutory
requirements.
Errors and omissions excepted.
Copyright © 2013. AVSL Goup Ltd