Quanshun Talkpod D5X User manual

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
User’s Manual
DMR Digital Portable Radio
D5X

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Acknowledgments!
Thank you for purchasing Talkpod DMR Digital Radio. As a product built to the DMR
standard, it is endowed with ergonomic design, all-round digital functions and
remarkable quality to refresh your experience and enable you to be responsive to
emergent situations.
To derive optimum performance from your product, please read this manual and the
supplied Safety Information Booklet carefully before use.
Please check the box of this product and see if there are signs of damage.
Need-To-Know
This radio is not intended for use by general population in an uncontrolled
environment. It is only for occupational use and only applied to work-related
conditions.
Only a professional technician is allowed for maintenance.
It is important that a user keeps good understanding and knowledge of general
danger information about Digital Radio.
This manual is suitable for using the model of TP-D5X.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Supplied Accessories
Audio Accessories
Charging Operation

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Charging Diagram
Attaching the battery
1. Insert the battery into top of the radio. See arrow 1 .
2. Slightly press the bottom of the battery until a click is heard. See arrow 2
To remove the battery, turn off the radio first. Then slide the battery latch upwards
to unlock the battery.
Attaching the Audio Accessory/Programming Cable
1. Open the accessory jack cover.
2. Align the plug with the accessory jack.
3. Tighten the screw on the plug.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Install antenna
BASIC OPERATIONS
Turning the Radio On/Off
Rotate the Radio On-Off/Volume Control knob clockwise/counter-clockwise until a
click is heard to turn the radio on/off.
Adjusting the Volume
After turning the radio on, rotate the Radio On-Off/Volume Control knob clockwise
to increase the call volume, or counter-clockwise to decrease it.
Selecting a Zone
A zone is a group of channels exhibiting the same property, and is programmed by
your dealer. The radio supports up to 2 zones, each with a maximum of 16 channels.
You may select a zone through any of the following methods: Through the function
keys
You may quickly toggle to your desired zone by pressing the programmed Zone Up or
Zone Down key.
Selecting a Channel
Rotate the Channel Selector knob to select a desired channel.
Switching the Channel Mode
Each channel can be programmed as either analog channel or digital channel. If the
current zone
Includes both analog and digital channels, you may quickly switch between digital
and analog channels.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Receiving and Making A CALL
To ensure an optimal volume of the receiving radio, hold the radio approximately 2.5
to 5 centimeters away from your mouth.
Private Call
1. Rotate channel switch to desired channel from user ID
2. Keep the radio 1-2 feet (2.5-5cm) away from mouth.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer.
3. Press PTT to answer LED lingt red.
4. Talk to microphone after active the tone of allowing calling tone.
5. Release PTT to receive information.
6. Radio automatically over the calling if there is no operation with permitted period.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer. Automatically over the
calling if there is no operation with permitted period.
7. Radio sounds a short tone.
Receiving and Responding to a Private Call
1. LED light green.
2. Keep the radio 1-2 feet (2.5-5cm) away from mouth.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer.
3. Press PTT to answer LED lingt red.
4. Talk to microphone after active the tone of allowing calling tone.
5. Release PTT to receive information.
6. Automatically over the calling if there is no operation with permitted period.
7. Radio sound a short tone.
Transmitting a Group Call
1. Program the radio as a group member to transmit any information to this group.
2. Rotate channel switch to desired contact ID or channel.
3. Keep the radio 1-2 feet (2.5-5cm)away from mouth.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer.
4. Press PTT to answer LED lingt red.
5. Talk to microphone after active the tone of allowing calling tone.
6. Release PTT to receive information.
7. Radio automatically over the calling if there is no operation with permitted period.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer. Automatically over the
calling if there is no operation with permitted period.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Receiving and Responding to a Group Call
Program the radio as a group member to receive any information from this group
calling.
1. LED light green.
2. Keep the radio 1-2feet (2.5-5cm) away from mouth.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer.
3. Press PTT to answer LED lingt red.
4. Talk to microphone after active the tone of allowing calling tone.
5. Release PTT to receive information.
6. Automatically over the calling if there is no operation with permitted period.
Transmitting an All Call
Program the radio with this function and transmit information to all users.
1. Rotate channel switch to desired channel from contact ID
2. Keep the radio 1-2 feet (2.5-5cm) away from mouth.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer.
3. Press PTT to answer LED lingt red.
4. Talk to microphone after active the tone of allowing calling tone. All the users on
this channel cannot answer the calling.
Receiving an All Call
All call is transmitting information to all the radios. Especially for releasing special
notice.
When receiving:
1. Radio sound a tone and LED light green.
2. Radio automatically over the calling if there is no operation with permitted period.
If the radio program the “Free Channel Indication”, release PTT to get a short tone,
that means it is free channel and wait for your answer.
NOTE: When receiving all call, you change to another channel, then will stop
receiving the all calling. And during receiving, you cannot use any programmed keys
until calling is over.
Calls on Analog Channels
To transmit on an analog channel, hold down the PTT and speak into the microphone.
To receive, release the PTT key.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Message
Send Pre-set Message
You can at most pre-set 50 pieces message.
1. Choose desired contact to send a pre-set message.
2. LED light red.
3. Two tons of “DiDi” means sending message successfully. A lower tone means no
message send.
Encryption
This function is only available for digital channel.
You can at most preset 16 list encryption, encrypted code(4 byte)by program
software and enable/disable this function.
Emergency Alarm
Press this programmed key to active emergency alarm.
Scan
Scan List
Create the scan list and allocate to single channel/contact list.
Through cycle scanning the listed channel/contact list to search the any
communication channel. It supports at most 250 list and 16 members for each list.
Scan
LED light red when scanning.
Two methods of scanning:
1. Main Channels(by manual):
Scan all channel/contact groups from all scanning lists.
When scanning, your radio automatically starts from the last scanned channel,
contact list or starting scanning channel.
2. Automatically manual:
Scanning start from the channel which be active automatically scanning.
Scan On/Off
1. Choose automatically scanning channel by press programmed key or rotate
channel switch.
2. When scanning active, LED light red and sound a confirm tone. Or stop scanning,
LED goes off and sound a negative tone.
Double Priority Channel
When radio enables this function, scan the priority channel and normal channel at
the every scanning with recycle scanning.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
During Scanning, Answer Calling
Stop at the detected active channel/contact list.
Radio keeps at this stop channel that is so called “Free Time” programmed period.
1. Keep the radio 1-2feet (2.5-5cm) away from mouth.
If the radio program the “Free Channel Indication”, release PTT to get a short
tone, that means it is free channel and wait for your answer.
2. Within the permitted period, Press PTT to call, LED light red.
3. Talk to microphone after active the tone of allowing calling tone.
4. Release PTT to receive information.
5. Radio automatically over the calling if there is no operation with permitted
period.
Settings
SQL
You can adjust the SQL to filter lower signal calling or channels with background
noise is higher than normal value.
Normal: default value.
High: filter no use calling or background noise, but may also filter the calling from
long distance.
1. Program the SQL key.
2. A positive tone means high SQL; a negative tone means normal SQL.
High/Low Power
High power enables communication with long distance radio. Low power enables
communication with short distance radio.
1. Program High/Low power key.
2. A positive tone means radio transmit at the low power; A negative tone means
radio transmit at the high power.
VOX
This function enables your radio to make a call with a programmed channel. No
matter when the accessories with VOX function detect the signal, radio will transmit
the information within programmed period.
Press PTT to disable VOX function.
Operate follow step to re-start the VOX:
Turn off the radio and power on again. Or rotate channel switch to another one. Or
operate the below.
NOTE: Enable or disable this function to those active radios.
1. Program the key with VOX function and can turn on/off.
2. Talk to microphone after active the tone of allowing tone.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Tone/Beeper ON/OFF
Enable/disable the key with tone/beeper if necessary.
1. Program the key with tone ON/OFF function.
2. A positive tone means turn on beeper/tone function; A negative tone means turn
off beeper/tone function.
Check Battery
LED light yellow: charging
LED light green: fully charged.
Press programmed key to check the battery capacity by the beeper.
1. Very low power: “Diling Diling” tones.
2. High: Three tones of “Diling Diling”.
3. Middle: Two tons of “Diling Diling”.
4. Low: One tone of “Diling Diling”.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Specifications
General
Model Number TP-D5X
Frequency Range UHF: 400-470MHz
Channel Capacity 32
Zone Capacity 2
Channel Spacing FCC FM:12.5KHz; 4FSK:12.5 KHz
CE FM:12.5KHz/25KHz; 4FSK: 12.5KHz
Increased Capacity TDMA divides a 12.5 kHz channel into
two alternating time slots.
Operating Voltage 7.4V
Battery 1650mAh Li-Ion Battery
Battery Life(5/5/90) 11Hrs @Analog; 16Hrs @Digital
Frequency Stability ±1.5ppm
Antenna Impedance 50Ω
Dimensions (H×W×D) 135x60x28(mm)
Weight 256g
Environmental
Operating Temperature -10℃to 55℃
Storage Temperature -40℃to 85℃
Operating Humidity 5% - 95% RH
Transmitter
RF Power Output UHF: High 4W - Low 1W
4FSK Digital Modulation 12.5KHz Data Ony:7K6ΦFXD;
12.5KHz Data & Voice: 7K6ΦFXE
Conducted/Radiated Emission -36dBm<1GHz
-30dBm>1GHz
FM Hum & Noise 12.5KHz @11K0F3E
Adjacent Channel Power 60dB @12.5KHz; 70dB @20/25KHz
Audio Response +1~-3dB
Audio Distortion ≤5%
Digital Vocoder Type AMBE++ or AMBE+2TM
Digital Protocol ETSI-TS102 361-1,2&3
Receiver
Sensitivity (Analog) 0.35µV/-116dBm (SINAD);
0.22µV/-120dBm (Typical)
Sensitivity (Digital) 0.35µV/-117dBm (SINAD);
0.22µV/-120dBm (Typical)
Rated Audio Power Output 1W
Rated Audio Distortion ≤3%
Audio Response +1 ~ -3dB
Conducted Spurious Emission ≤-57dBm

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
NOTE: Specifications will be revised without notice due to technical improvement. Thank you.
Trouble shooting guide
Troubles Solution
No Electrical Source 1. The battery has been exhausted.
Replace the battery.
2. The battery is installed incorrectly.
Remove it and install again.
The operating time becomes short, even
the battery is fully charged
Replace the battery
Not able to communicate with the
transceivers of the same group
1.Confirm the QT/DQT and frequency are
the same
2.The distance is outside of range
The voice of another group can be heard Change all QT/DQT of the group
Noise is always heard The distance is outside of range, turn on
the radio in nearer range and try again

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
Warning Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
RF Energy Exposure Awareness and Control Information and Operational
Instructions for Occupational Use
Notice: this radio is intended for use in occupational/controlled conditions where users have full
knowledge of their exposure and can exercise control over their exposure to meet the
occupational limits in FCC and International standards. This radio device is NOT authorized for
general population consumer use.
Federal Communication Commission (FCC) Regulations
When DMR Digital Portable Radio used as a consequence of employment, the FCC requires users
to be fully aware of and able to control their exposure to meet occupational requirement.
Exposure awareness can be facilitated by the use of a product label directing users to specific
user awareness information. Your DMR Digital Portable Radio has a RF Exposure Product Label.
Also, your DMR Digital Portable Radio user manual includes information and operating
instructions required to control your RF exposure and satisfy compliance requirements.
Compliance with RF Exposure Standards
Your DMR Digital Portable Radio is designed and tested to compliance with a number of national
and international standards and guidelines for human exposure to radio frequency
electromagnetic energy. This radio compliance with the IEEE (FCC) and ICNIRP exposure limits for
occupational/controlled RF exposure environments at operating duty factors of up to 50% talk –
50% listen and is approved for occupational use only. In terms of measuring RF energy for
compliance with these exposure guidelines, your radio generates measureable RF energy only
while it is transmitting (during talking), not when it is receiving (listening) or in standby mode.
Your DMR Digital Portable Radio complies with the following RF energy exposure standards and
guidelines:
● United States Federal Communications Commission (FCC), Code of Federal Regulations;
● Institute of Electrical and Electronic Engineers (IEEE) C95.1
● International Commission on Non-lionizing Radiation Protection (ICNIRP)
RF Exposure Compliance and Control Guidelines and Operating Instructions for
Two-Way Radio Operations
To control your exposure and ensure compliance with the occupational/controlled environment
exposure limits, always adhere to the following procedures;
● DO NOT remove the RF Exposure Label from the device
● User awareness instructions should accompany device when transferred to other users.
Operational Instructions and Training Guidelines
To ensure optimal performance and compliance with the occupational/controlled environment
RF energy exposure limits in the above standards and guidelines, users should transmit no more
than 50% of the time and always adhere to the following procedures;
● In front of the face, hold the radio in a vertical position with microphone (and other parts of
the radio including the antenna) at least one inch (2.5 centimeters) away from the nose or lips.
Keep the radio at a proper distance is important to ensure compliance.
Note: RF exposure decrease with increasing distance from the antenna.
● Body Worn Operation; When worn the body, always place the radio in an approved clip,
holder, or body harness for this product.
Using approved body-worn accessories is important because the use of non-approved
accessories may results in exposure levels, which exceed the occupational/controlled

Quanshun Communication Technology Co., Ltd
Add: Quanshun Bldg., Daxiamei, Nan'an, Quanzhou, Fujian, China 362302
Tel: [phone] Fax: [phone]
environment RF exposure limits
Using only approved supplied or replacement antennas, batteries, and audio accessories, use of
non-approved antennas, batteries, and wired or wireless accessories may exceed the applicable
RF exposure guidelines (IEEE, ICNIRP or FCC).