Quoizel PRV8408K User manual

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PRV8408K_R1
For Style PRV8408K
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Fixture Body
x1
C
D
Crossbar
Assembly
x1
RevisedDate:2016-06-01
Cage with Shade
x1
STEP 1 Install Bulbs, Cage with Shade and Fixture Body-
A. This fixture uses candelabra bulb with standard screw base.
Maximum 60 watts. Insert bulb and screw snugly into place.
B. Remove Lock Screws from top edge of Cage with Shade (D).
Lock
Screw
Socket
Figure 1
C
C. Insert sockets inside of shade diagonal (Refer
to Direction of Installing Sockets). Rotate
Fixture Body (C) and align holes on fixture
hood to mounting holes on top edge of the
cage. Secure them together with removed
Lock Screws. Tighten until snug with
screwdrivers.
Fixture Hood
Shade
Mounting
Hole
C
D
C
D
D
Bulb (not
Supplied)
Socket Socket
Direction of
Installing Sockets
Pleasegoto forproductcleaningtips.Gotothe selection.
(2)B10CandelabraBasebulb60WMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
B
Alternate
Mounting
screw
x2
STEP 2 -Install Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
Figure 2
A
Mounting Screw
or Alternate Short
Mounting Screw
C
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw
STEP 3 -Test Fitting Backplate to Crossbar Assembly
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (C) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (C)
should be snug against the wall and the mounting balls. If not, adjust
the length of the mounting screw or alternate short mounting screw
on the Crossbar Assembly (A) by unscrewing the preassembled hex
nut and lock washer and then screwing the mounting screws or
alternate short mounting screws in or out of the crossbar until the
correct length is achieved. Once the backplate on Fixture Body (C)
is secure, remove the mounting ball and Fixture Body (C) and
proceed to Step 4.
Figure 3
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com

2of2
2016 QuoizelInc.
Fixture can
only be
mounted in
the direction
indicated
4.5”
6.5”
PRV8408K
FINISH: MYSTIC BLACK
PART NUMBER
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
1
NO. PART NUMBER REPLACEMENT PART QTY.
G3970SH SHADE 1
(2) 60W Candelabra
Bulbs
(Not Supplied)
Base
9.5”
17.5”
6.5”Sq.
8.5”Sq.
9.5”
1
Cup Head
Screw
Cup Head
Screw
Lock Washer
Side
Arm
Shade
Shade Holder
Ring
STEP 2 Replace Shade-
Quoizel recommends two people for
this step.
A. Remove two Side Arms by
unscrewing Cup Head Screws on
the top and bottom of Shade
Assembly.
B. With one person hold fixed Side
Arms, another person replace
the Shade inside of the Side
Arms.
C. Reassemble removed Side Arms
back onto the Shade Assembly
and secure with Cup Head
Screws. Tighten until snug.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 -Install Fixture
Body
A. Carefully tuck all wires
into the outlet box and
position the backplate of
Fixture Body (C) over the
outlet box. Align the
holes in the backplate
with the mounting
C
Mounting
Ball
A
Backplate
Mounting Screw
or Alternate Short
Mounting Screw
screws or alternate short
mounting screws. Place caulk
(not supplied) into the previously
removed mounting balls and
then attach Fixture Body (C)
using the mounting balls. Hand
tighten until snug. Figure 5
Figure 6
STEP 6 -Apply Silicone Sealer
A. Make sure exterior wall surface
and fixture backplate are free of
dirt before applying caulk. Using
exterior grade caulk, caulk over
top of backplate and down other
side. Do not caulk bottom of
fixture backplate to ensure
proper moisture drainage.
Your fixture is now assembled
and ready to use. Enjoy!
Exterior
Grade
Caulk
Backplate
STEP 1 Remove Shade Assembly-
A. Remove Bulbs from Sockets.
B. Remove Cage with Shade from
Fixture Body by unscrewing Lock
Screws on the Fixture Hood.
Replace Shade
Socket
Lock Screw
Fixture
Hood
Bulb
Cage with
Shade
RevisedDate:2016-06-01
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com