Quoizel CHI8413IB Mounting instructions

Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing
the fixture. We strongly recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool
before removal. Do not subject glass parts to any shock while in operation or shattering may result.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc.
1of8
Assembly Instruction Sheet #IS-CHI8413IB
For Style CHI8413IB
Part Description Quantity
AInner Backplate
Wall Anchor
1pc.
2 pcs.
2 pcs.
2 pcs.
4 pcs.
4 pcs.
4 pcs.
2 pcs.
B
C
D
E
Mounting Screw (1.5”L)
Mounting Screw 1.25”L)
(
Package Contents
Lock Washer
Self-tapping Screw
A
BC
DE
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers, wire cutters, wire
strippers,electrical tape, safety glasses.
EstimatedAssemblyTime:20-30 minutes
BulbRecommended: (4) Candelabra Base Bulbs 60W Maximum
Preparation:Identify and inspect all parts before beginning installation. Check package
contentlist and diagrams below to be sure all parts are present. If any parts are missing
ordamaged,do not attempt to assemble, install, or operate the fixture. Contact customer
serviceforreplacementparts.
March2013
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC
29445
Customer Service
Phone [phone]
Fax [phone]
www.quoizel.com
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
F
F
Hex Nut
Mounting Ball
G
H
G
Fixture Body
H
I
1pc.
I
J
Cage with Shade 1pc.
J

CHI8413IB
FINISH: IMPERIAL BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/2"
1
2
PART NUMBER REPLACEMENT PART DESCRIPTION REQ.
1
1
NO.
2of8
18413IBCHI
G3543SH
BASE CHI8413IBIMPERIAL BRONZE
SHADE CLEAR WATER GLASS
(4)60W Candelabra
Base Bulbs
(not Supplied)
16”
13” Dia.
28”
11”x7”
11.5”
9” Dia.
1
2

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc.
3of8
STEP 1 Remove PE Foam and Sponge-
A. Take out the Glass by unscrewing Lock Screws and
Tabs. Remove PE Foams and Sponges around the
Glass.
B. Place the Glass back into the Cage and secure with the
Tabs and the Lock Screws..
C. Unscrew the Socket Head Cap Screws from the top
edge of the Cage.
Assembly Instruction Sheet #IS-CHI8413IB
For Style CHI8413IB
March2013
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Lock
Screw
PE Foam
(Remove)
Sponge
Figure 1
Tab
Sponge
(Remove)
Glass
Socket Head
Cap Screw
Cage
PE Foam

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc.
4of8
STEP 2 Install Cage-
A. Place the Cage (J) over the Sockets at the Fixture Body
(I). Attach to the Fixture Hood. Secure by threading the
Socket Head Cap Screws into the mounting holes on
the top edge of the Cage. Hand tighten until snug.
Assembly Instruction Sheet #IS-CHI8413IB
For Style CHI8413IB
March2013
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Cage
Socket Head
Cap Screw
Fixture
Hood
Figure 2
Fixture Body
STEP 3 Drill Holes for Wall Anchors-
A. Attach the Inner Backplate (A) onto the Outlet Box. Line
up a set of hole on the Inner Backplate (A) and the
mounting holes on the Outlet Box. Mark two points on
the wall from a set of holes on the bottom end of the
Inner Backplate (A).
B. Remove the Inner Backplate (A). Drill proper holes on
the wall for Wall Anchors (B).
Inner
Backplate
Outlet Box
Hole
Figure 3

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc.
5of8
Assembly Instruction Sheet #IS-CHI8413IB
For Style CHI8413IB
March2013
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
STEP 4 Install Mounting Screws-
A. Thread the Mounting Screws (D/E) into (4) Mounting
Holes on the Inner Backplate (A). Thread the Lock
Washers (F) and the Hex Nuts (G) onto the Mounting
Screws (D/E). Hand tighten until snug.
Lock
Washer
Mounting
Screw (1.5”L)
Inner Backplate Hex
Nut
STEP 5 Install Inner Backplate-
A. Insert the Wall Anchors (B) inside of the drilled Holes on
the wall.
B. Place the Inner Backplate (A) onto the Outlet Box.
Secure it by threading the Outlet Box Screws (not
supplied) into the mounting holes on the Outlet Box and
thread the Self-tapping Screws (C) into the Wall
Anchors (B). Hand tighten until snug.
Outlet Box Screw
(Not Supplied)
Self-tapping
Screw
Wall Anchor
Outlet Box
Hole
Figure 4
Figure 5
Mounting
Screw (1.25”L)

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc.
6of8
STEP 6 -Attach Lanyard
A. The purpose of the lanyard is to provide the installer a
means to support the fixture from the junction box while
connecting the electrical wires. This enables the fixture
to hang from the junction box and your hands are free to
make the wire connections.
B. Turn the Button Stop so it may be inserted into the
crossbar slot. Make sure the Button Stop is completely
inside the crossbar. Slowly release the fixture to make
sure it is supported by the Button Stop. Proceed to the
wiring steps. Once you are complete with the wiring
there is nothing to do with Lanyard. The Lanyard will
push into the junction box when the fixture is placed for
final mounting.
Assembly Instruction Sheet #IS-CHI8413IB
For Style CHI8413IB
March2013
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Inner
Backplate
Slot
Button Stop
Lanyard
STEP 7 -Make Wire Connections
A. Use standard wire connectors to make all wire
connections. (Connectors are not included with fixture.)
Strip and prepare wire ends according to instructions
supplied with connectors.
B. Connect White Supply Wire from the Outlet Box to
White Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet
BoxtoBlackWirefromfixture.
D. Connect Ground Wire from the Outlet Box to Ground
Wire from fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape
and carefully stuff all the connected wires into the
Outlet Box.
Figure 8
White wire from supply White wire from fixture
Black wire from supply
(or Red)
Black wire from fixture
Ground wire from supply Ground wire from fixture
Figure 7
Figure 6

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc.
7of8
STEP 8 Install Fixture Body-
A. Attach the Fixture Body (I) onto the Inner Backplate (A).
Pass the holes on the backplate of the Fixture Body (I)
over the Mounting Screws (D/E) and secure with the
Mounting Balls (H). Hand tighten until snug.
Figure 9
Inner
Backplate Mounting
Ball
Mounting Screw
Assembly Instruction Sheet #IS-CHI8413IB
For Style CHI8413IB
March2013
Figure 10
Socket
Bulb
STEP 9 -Install Bulb
A. bulb with a standard
screw base 0
This fixture uses Candelabra
. Maximum 6 watts.
B. Insert bulb and screw snugly into place.
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Fixture
Body

Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2013 QuoizelInc.
8of8
Assembly Instruction Sheet #IS-CHI8413IB
For Style CHI8413IB
March2013
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
STEP 10 Apply Silicone Sealer-
A.
B. Make sure exterior wall surface and fixture backplate
are free of dirt before applying caulk. Using exterior
grade caulk, start on one side of fixture backplate and
follow contour, where the fixture backplate meets the
exterior wall surface upward. Proceed to caulk over top
of backplate and down other side. Do not caulk bottom
of fixture backplate to ensure proper moisture
drainage.
To prevent moisture from entering the wire
compartment, apply a small amount of silicone sealer
(not included) to the threaded side of the mounting
balls (H) and then install them onto the mounting
screws (D/E). Wipe off excess caulk.
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade Caulk
Outdoor Fixture
Backplate
Exterior
Wall Surface
Figure 11
Mounting
Ball